686377

Kemppi A3 MIG Welder Manual

9
Zoom out
Zoom in
Previous page
1/22
Next page
9
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
4. SYSTEM CONFIGURATION
This section describes the settings that are typically
made once or that are otherwise necessary for integration
to be completed successfully. It does not describe those
settings that aect welding quality and are modied based
on the welding operation. For more information on the
operation-based settings, see the A3 MIG Welder Operating
manual.
Use the control panel and the DIP switches to perform
the system conguration within the integration.
4.1 Configure sensors and devices
Touch sensor output voltage
Use the DIP switches to set the touch sensing voltage
between +50…+200 V. Change the value during operation
depending on the work piece surface properties, if needed.
P2 switches 1-2 Voltage
ON
1 2 3 4 5 6 7 8
50 V
(default)
ON
1 2 3 4 5 6 7 8
80 V
ON
1 2 3 4 5 6 7 8
110 V
ON
1 2 3 4 5 6 7 8
200 V
Safety stop on/o
Use the DIP switches to set the emergency stop input on
and o. If you have installed an emergency stop switch
circuit for the system, set the emergency input to be on
accordingly. Otherwise, ensure that these parameters are
set to o to prevent possible false detection.
P2 switch 3 Safety stop
ON
1 2 3 4 5 6 7 8
Disabled (default)
ON
1 2 3 4 5 6 7 8
Enabled
Collision sensor on/o
Use the DIP switches to set the collision sensor on and o.
If you haven’t got a collision sensor installed in the system,
turn the sensor o to prevent possible false detections.
P2 switch 4 Collision sensor
ON
1 2 3 4 5 6 7 8
Disabled (default)
ON
1 2 3 4 5 6 7 8
Enabled
Collision sensor switch type
Use the DIP switches to select the switching type of
the collision sensor. The switch can be either opening
or closing. See Figure 3.4, “Opening and closing action
switches”.
P2 switch 5 Switch type
ON
1 2 3 4 5 6 7 8
Opening (default)
ON
1 2 3 4 5 6 7 8
Closing
Byte order
Use the DIP switches to select the byte order according to
the robot type.
P2 switch 6 Byte order
ON
1 2 3 4 5 6 7 8
Little-endian (default)
ON
1 2 3 4 5 6 7 8
Big-endian
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A3 MIG Welder at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A3 MIG Welder in the language / languages: English as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info