686376
21
Zoom out
Zoom in
Previous page
1/32
Next page
21
A3 MIG Welder© Kemppi Oy 2018 1826
OPERATING MANUAL
Regular MIG welding parameters
Parameter Display Value range Factory
setting
Description
Pre-gas time
PrG
0.0 ... 9.9 s 0.0 s Pre-gas time in seconds
Post gas time
PoG
0.1 ... 9.9 s,
aut (Aut)
Aut Post gas time in seconds or
automatically according to the welding
current (Aut).
Creep start
level
Cre
10 ... 170 % 50 % Percentage of wire feed speed:
10%-99% = slow start
100% = no creep start
101%-170% = accelerated start.
Start power
sta
-9 … +9 0 Strength of start pulse
Post current
time
PoC
-9 ... +9 0 Post-welding current time
Synergic MIG welding parameters
Parameter Display Value range Factory
setting
Description
Pre-gas time
PrG
0.0 ... 9.9 s,
syn (Syn)
Syn Pre-gas time in seconds or
automatically according to the synergic
welding program (Syn).
Post gas time
PoG
0.1 ... 9.9 s,
syn (Syn)
Syn Post gas time in seconds or
automatically according to the synergic
welding program (Syn).
Creep start
level
Cre
10 ... 170% 50 % Percentage of wire feed speed:
10%-99% = slow start
100% = no creep start
101%-170% = accelerated start.
Hot start
level
Hot
-50 ... 75 % 30 % Percent of welding power: -50% refers
to cold start and +75% to hot start.
Hot start time
h2t
0.0 … 9.9 s 1.2 s The duration of the hot start in
seconds.
Crater ll
start level
crs
Crater ll
end level …
250 %
90 % The welding power at the beginning of
the crater ll stage as a percentage of
the welding power pre-set value.
Crater ll end
level
CrL
10 % ... Crater
ll start level
30 % The welding power at the end of the
crater ll stage as a percentage of the
welding power pre-set value.
Crater ll
time
crt
0.0 … 9.9 s 2.0 s The duration of the crater ll stage in
seconds.
Start power
sta
-9 … +9 0 Strength of the start pulse (not in
WiseRoot or WiseThin processes).
Post current
time
PoC
-9 ... +9 0 Post-welding current time
Synergic MIG
display units
Unl
m/min,
mm, A
m/min In 1-MIG and WiseRoot welding, the
parameter shown in the left-hand
side display: (wire feed speed (m/
min), sheet thickness (mm) or average
current (A).
Common system setup parameters
Parameter Display Value range Factory
setting
Description
Cable
compensation
CAL
-5.0 ... 9.0 V
/100 A
1.0 V/100 A Cable compensation (MIG) for
voltage losses.
Long system
mode
lsy off (O),
on (On)
O Gives optimum welding
characteristics with long welding
cables. Recommended to be used
when the cable length exceeds 40 m.
Code entry
Cod ---, Ent
(Ent)
Entering license code manually. See
page 15 for details.
Scaling
SCA
0 ... 9999 0 A coecient with which the values
in the welding machine are scaled to
the scale used by the robot.
Restore factory
settings
FAC OFF (O),
Pan (Pan),
All (All)
O Restores factory settings if you
select PAN or ALL and exit the menu.
PAN will reset the panel settings
and leave the memory channels
untouched. ALL restores the whole
system to the factory state.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A3 MIG Power Source 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A3 MIG Power Source 400 in the language / languages: English as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info