478051
4
Zoom out
Zoom in
Previous page
1/16
Next page
Installing your refrigerator
The appliance should arrive with the
front adjustable rollers wound down to
tilt the top of the refrigerator backwards
by about 10 -15mm from upright.
The stability foot should also be wound
fully up so it will not interfere with the
operation of the rollers (see diagram
in Step 3 below).
caution
Therollersaredesignedforforwardorbackward
movementonly.Theyarenotcastors.Movingthe
refrigeratorsidewaysmaydamageyouroorand
the rollers.
1. Roll the refrigerator into its nal position.
2. The top of the refrigerator should be tilted back by
approximately 10 -15mm. This will allow the doors to
self-close providing a consistent door seal.
3. If the refrigerator is not tilted back, you can adjust the
two front rollers by turning the large, plastic roller nut
(see diagram below). This will increase the height of the
rollers. One turn of the nut will tilt the refrigerator back
approximately 10mm. If you have difculty turning the
roller nut you can have someone tilt the refrigerator back,
so that you have better access. Alternatively, you can
access the rollers from the side, using a at screwdriver
to help you turn the nut (see diagram below).
4. Check the alignment of the refrigerator to the
surrounding cupboards. The top of the refrigerator
should be level from side to side (see diagram below).
If you need to adjust the level, use the adjustable rollers
as discussed in Step 3.
Installing your new refrigerator
ClearancearoundyourSidebySiderefrigerator
Your Side by Side Refrigerator can be installed between
cupboards or xtures but you must allow for the following
spaces around the cabinet.
1. allow a minimum of 5mm clearance on both sides.
2. allow 10mm clearance at the back of the refrigerator.
3. allow a minimum of 10mm clearance above hinge covers.
4. allow a 250 or 350mm clearance on the hinge side of
the doors, if you place the refrigerator next to the wall.
This will make cleaning easier.
5. make sure that cupboards or xtures do not stick out
further than the refrigerator cabinet.
ClearancearoundyourTopandBottomMountrefrigerator
1. allow a minimum of 5mm clearance on both sides.
2. allow 10mm clearance at the back of the refrigerator.
3. allow a minimum of 10mm clearance above hinge covers.
4. If you do not have a cupboard with a rear gap, the
recommended clearance area on top increases from
50mm to 90mm.
5. When positioned in a corner area, spacing of at least
350mm on the hinge side will allow the doors to open
enough to enable the removal of bins and shelves.
Note: Doors on all models are designed to sit proud of
cabinetry (not ush). The refrigerator should be placed
against a wall and the gap between the rear of the
refrigerator and the wall should be no greater than 75mm.
90mm
50mm
30mm
30mm
Recommended
airspace
CABINET
DOOR
350mm
10-15mm
Fixed rear
rollers
Height adjustable
front rollers
Top of refrigerator
is level ie. horizontal
Adjust front rollers
for uneveness of floor
eg. wind this roller
down or up
Aligned to
cupboards
ie. even gap
4 Installing your new refrigerator Kelvinator Refrigeration
Stability foot
wound up
Large plastic
roller nut
10mm
5mm
5mm
Recommended
airspace
CABINET
DOORS
10mm
35mm
Freezer
Door
Fridge
Door
250mm
350mm
10mm
5mm
5mm
Recommended
airspace
CABINET
DOORS
10mm
35mm
Freezer
Door
Fridge
Door
250mm
350mm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kelvinator KBM5100WB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kelvinator KBM5100WB in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info