598220
29
Zoom out
Zoom in
Previous page
1/476
Next page
Getting Started
2001-900-01 Rev. K/ August 2010 2-15
2.6.7 Syntax rules
The following information explains some of the
programming syntax for the Model 2001. For more complete
information, see paragraph 4.9.
General form
The general form for SCPI commands is demonstrated in
Table 2-7. Notice that they are hierarchical in nature and
begin with a root command. For example, to set autoranging
on the DC voltage function, you would send the following
command:
q~ÄäÉ=OJT
Abbreviated SCPI command summary
:SYSTem
:PRESet
Subsystem command path.
Set unit to a default configuration (see Appendix A).
[:SENSe[1]]
:VOLTage[:DC]
:APERture <n>
:AVERage
:COUNt <n>
:STATe ON|OFF
:NPLCycles <n>
:RANGe
[:UPPer] <n>
:AUTO <b>
:REFerence <n>
:RESolution <n>
Subsystem command path.
Path to configure DC voltage.
Specify integration time in seconds (n = 166.67e-6 to 200e-3).
Path to control averaging filter:
Specify number of points to average (n = 1 to 100).
Enable/disable averaging filter.
Specify integration time in number of line cycles (n = 0.01 to 10).
Path to configure measurement range:
Select range (n = -1100 to +1100).
Enable (1 or ON) or disable (0 or OFF) autorange.
Specify REL value (n = -1100 to +1100).
Specify measurement resolution (number of digits; n = 4 to 8).
:INITiate
:ABORt
:ARM
:LAYer2
:COUNt <n>|INF
:DELay <num>
:SOURce HOLD|IMMediate| TIMer|
MANual|BUS|TLINk| EXTernal
:TIMer <num>
Initiate one trigger (measure) cycle.
Reset trigger system and go to idle state.
Subsystem command path to configure scan:
Path to program scan layer:
Program number of scans (1 to 99999 or INFinite).
Program delay (0 to 999999.999sec).
Select event to control scan trigger.
Set timer interval (0.001 to 999999.999sec).
:TRIGger
:COUNt <n>|INF
:DELay <num>
:SOURce HOLD|IMMediate|MANual|
BUS| TLINK| EXTernal|TIMer
:TIMer <num>
Subsystem command path to program measure layer:
Program number of measurements (1 to 99999, or INFinite).
Program delay (0 to 999999.999sec).
Select event to control measure trigger.
Set timer interval (0.001 to 999999.999sec).
:ROUTe
:CLOSe <list>
:STATe?
:OPEN <list>|ALL
:SCAN <list>
:EXTernal <list>
Subsystem command path for scanning.
Path and command to close channel.
Request closed status of channel list.
Open specified channels.
Path and command to specify internal list.
Command to specify external list.
Notes:
1. Command short form is indicated by the uppercase characters. For example, instead of sending “:arm:layer2:source immediate”, you can send
“:arm:lay2:sour imm”.
2. The brackets [ ] indicate optional names that need not be sent. For example: [:SENSe[1]]:VOLTage:DC:RANGe:[UPPer] 5 is the same as
:VOLTage:DC:RANGe 5.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Keithley 2001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Keithley 2001 in the language / languages: English as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info