771569
41
Zoom out
Zoom in
Previous page
1/48
Next page
Trobleshooting guide
Failure Possible reason What to do
1) Airflow rate is lower than duty one.
Air filter(s) dirty. Clean or replace air filter(s).
Plant air resistance higher than expected. Check air plant project.
Adjusting dampers closed. Open the dampers and
balance the plant.
Fans speed setpoint too low. Increase fan speed by AHU Kit control panel.
Increase fan speed set point of VSD option, if pre-
sent.
2) Airflow rate is higher than duty one.
Internal component missing (filter ?). Install the missing component (while unit is off)
Access panels open. Close the access panels.
Plant air resistance lower than expected. Balance the air plant by dampers.
Check plant project.
Reduce fan speed setpoint.
3) Heating/cooling capacity is lower than expected
Not enough air flow rate. (See failure 1).
Valve control is not right. Check connection between actuator and controller/
change temperature setpoint by remote control
panel.
4) Water condensate not discharged. Syphon wrong or missing. Install well-sized syphon.
5) The fans do not work.
The power supply is not inserted. Check the power supply electric unit and the elec-
tric line upstream of the plant itself (by the User).
Check and if necessary restore the electrical con-
nections by qualified personnel.
The thermostat switches are not in the exact fun-
ctioning position. Reposition the switches correctly and check their
status.
There are foreign bodies
that block the rotors. Remove the foreign bodies from the impellers, and
keep them clean, check that there are no impedi-
ments, check their integrity.
Loosened electric connections. Check presence of 0-10 V control signal (EC
motor).
6) Motor out of absorption.
Static pressure at that requested and therefore ex-
cessive flow rate. It is possible to intervene by increasing the load
using dampers and adjusters.
Rotation speed too fast. Check plant project.
Reduce fan speed setpoint.
7)Noise.
Excessive flow rate. (See failure 2).
Wear or cracks in the bearings. Contact the technical assistance service.
Presence of foreign material in the auger. Remove the foreign bodies from the impellers, and
keep them clean, check that there are no impedi-
ments, check their integrity. Contact the technical
assistance service.
8) Strong vibrations.
Rotor unbalanced due to wear or deposits of dust. Contact the technical assistance service.
The rotor rubs against the auger due to deforma-
tions. Contact the technical assistance service.
Obstructions in the ducts. Open the unit, check and clean the ducts, check
their tightness.
11 - IDENTIFYING BREAKDOWNS
pag. 41
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KRE-1500DX1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KRE-1500DX1 in the language / languages: English as an attachment in your email.

The manual is 3.62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info