771478
26
Zoom out
Zoom in
Previous page
1/44
Next page
&1
&1 &1 &1 &1 &1
&1
&1
&1
&1
&1
&1
&1 &1
&1 6 6
',6
&1
&1 6 6
&1 &1
&1
&1
&1
&1
6:
&1
      
               

&1 &1 &1
HC
7.6.4 For smart grid:
The unit has smart grid function, there are two ports on PCB to connect
SG signal and EVU signal as following(SG is municipal power, and
EVU is free power):
Method A
Method B
Method C (Double zone control)
Indoor unit is connected with two room thermostat, while user
interface FOR SERVICEMAN set ROOM THERMOSTAT to
DOUBLE ZONE:
C.1 When unit detect voltage is 12VDC between HT and COM ,
zone1 turn on. When unit detect voltage is 0VDC between HT
and COM, zone1 turn off.
C.2 When unit detect voltage is 12VDC between CL and COM,
zone2 turn on according to climate temp curve. When unit detect
voltage is 0V between CL and COM, zone2 turn off.
C.3 When HT-COM and CL-COM are detected as 0VDC, unit turn off.
C.4 when HT-COM and CL-COM are detected as 12VDC,
both zone1 and zone2 turn on.
1.When EVU signal is on, and SG signal is on, as long as the DHW mode is set to
be valid, the heat pump and IBH will operate in DHW mode at the same time
automatically.When T5 rises to 60°C,the DHW mode will exit and switch to cooling/
heating mode normally.
2.When EVU signal is on, and SG signal is off, as long as the DHW mode is set to
be valid and the mode is on,the heat pump and IBH will operate in DHW mode at
the same time automatically,when T5≥Min(T5S+3,60),the DHW mode will exit and
switch to cooling/heating mode normally.(T5S is the setting temperature)
3.When EVU signal is off, SG signal is on, the unit operates normally.
4.When EVU signal is off, and SG signal is off, the unit operates as below: The unit
will not operate DHW mode, and the IBH is invalid, disinfect function is invalid. The
max running time for cooling/heating is “SG RUNNING TIME”, then unit will be off.
(98 6*
&/
&20
+7
&1 &1
NOTE
The wiring of the thermostat should correspond to the
settings of the user interface. Refer to ROOM
THERMOSTAT.
Power supply of machine and room thermostat must be
connected to the same Neutral Line .
When ROOM THERMOSTAT is not set to NON, the
indoor temperature sensor Ta can’t be set to valid
Zone 2 can only operate in heating mode, When cooling
mode is set on user interface and zone1 is OFF,“CL” in
zone2 closes, system still keeps 'OFF'. While installation,
the wiring of thermostats for zone1 and zone2 must
be correct.
a) Procedure
Connect the cable to the appropriate terminals as shown in
the picture.
Fix the cable with cable ties to the cable tie mountings to
ensure stress relief.
RT1=1# Room Thermostat
RT2=2# Room Thermostat
23
CN24
CN21 CN5 CN28 CN8 CN6
CN16
CN32
CN13
CN15
CN29
CN18
CN42 CN25
CN40 S1 S2
DIS1
CN31
CN41
S3 S4
CN22 CN4
CN35
CN1
CN36
SW9
CN2 CN17
1 2 345 6 78 9 10 11 12 25 26 27 28
453 2 1
13 14 15 16 17 18 19 20 21 22 23 24 29 30 31
32
678 9 10
CN11 CN7 CN30
SMART GRID
EVU SG
CL
COM
HT
CN14 CN19
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KHPI-BI-10VR2XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KHPI-BI-10VR2XL in the language / languages: English as an attachment in your email.

The manual is 38.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KHPI-BI-10VR2XL

Kaysun KHPI-BI-10VR2XL User Manual - German - 44 pages

Kaysun KHPI-BI-10VR2XL User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info