771525
39
Zoom out
Zoom in
Previous page
1/45
Next page
Page 39
Wiring
1) The output of the mainboard engineering
load control interface is a strong electric
signal, so it must be powered o.
2) The engineering load control interface is only
used as a signal output. The total output
current of the mainboard cannot exceed
2.5A, otherwise it will cause overload and
damage the machine.
3) Please connect the engineering load in strict
accordance with the wiring diagram. The
excessive load power needs to be controlled
by the AC contactor. AHS and K_heater2
must pass the AC CONTACTOR control.
4) The connection and installation of external
engineering loads must be well protected,
such as earthed eectively, air switch and
residual current operated circuit-breakers.
The installation of engineering load shall be
installed in strict accordance with the
instruction manual of the load and control
components and local regulations.
"CN400" terminal is used for remote ON-OFF
switch; when using this function, this interface
is connected to external control switch,
remove the short connector of JR400 when
you use the "ON-OFF" function.
The control logic is as follows:
Remote switch short circuit: the machine is
controlled as normal.
Remote switch o: the machine enters remote
control.
3. Remote switch function
4. DIP SWITCH FUNCTION
5. Battery installation
1. The battery is placed in the accessory bag and
needs to be installed in the wired controller on
site.
2. Please remove the wired controller, place the
battery in the unit and ensure the positive side
of the battery is in accordance with the polarity
markings.
3. Set the correct time before operating. Battery
in the wired controller can maintain the correct
time during a power failure. When the power is
restored and the displayed time is not correct,
replace the battery.
Engineering load control interface
2-WAY VALVE
CODE PART NAME
SV2
Sv3_1,SV3_2 3-WAY VALVE
AHS CONTROL SIGNAL OF ASSISTANT
HEAT SOURCE
Pumpo PUMP
PumpT PUMP FOR RETURN WATER/PUMP
FOR MIXING WATER
K_heater2 CONTROL SIGNAL OF WATER
TANK HEATER
RY2,RY4 RELAY
DIP SWITCH
SW1
TW1B
ONFUNCTION DEFAULT SETTINGOFF
SW1-1
ON
1 2 3 4
SW1
SW1-3
SW1-2
SW1-4
OFF
OFF
OFF
OFF
TH
TK
WITHOUT
TW1B
WITH
TW1B
WITHOUT
TH
WITH
TH
WITHOUT
TK
WITH
TK
Note:Slide the switch
to numbers position
indicates OFF ." "
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KHHP-BI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KHHP-BI in the language / languages: English as an attachment in your email.

The manual is 18.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KHHP-BI

Kaysun KHHP-BI User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info