771475
17
Zoom out
Zoom in
Previous page
1/48
Next page
5.4.3 Application 3
Space cooling and heating application with a standard controller (or optional wired controller) connected to the unit. Heating
is provided through floor heating loops and fan coil units. Cooling is provided through the fan coil units only.
4
T1
T2
12
Tn
15
1
M1
M2
Mn
9.1
10
14
FCU1
FCU2
FCUn
11
12
5
M
9
13
9.2
2
3
6
7
8
FHL1
FHL2
FHLn
1 outdoor unit
2 Y-shape filter
3 shut-off valve (field supply)
4 wired controller (optional)
5 non-return valve (field supply)
6 drain valve (field supply)
7 fill valve (field supply)
8 buffer tank (field supply)
9 balance tank (field supply)
9.1 air purge valve
9.2 drain valve
10 expansion vessel (field supply)
11 Pump 2: outside circulation pump (field supply)
12 collector (field supply)
13 mixing station (field supply, field control)
14 Motorised 2-way valve to shut off the floor heating loops during
cooling operation (field supply, field control)
15 by-pass valve (field supply)
FHL 1...
n
floor heating loop
FCU 1...
n
fan coil units
M1...n
motorised valve to control loop FHL1...3 (field supply)
T1…n
room thermostat (field supply)
NOTE
If the volume of balance tank (9) larger than 30L, the buffer tank(8) is unnecessary, otherwise the buffer tank(8) should be installed and the
total volume of buffer tank and balance tank should larger than 30L.The drain valve (6) should be installed at the lowest position of the
system.
An independent backup heater can be selected and installed in the door, which can provide additional heating source and ensure better
performance of the system when the ambient temperature is low.
Mixing station
As the unit is mainly to provide middle-temperature and high-temperature water, when connecting floor heating, the need to increase the
mixing station (13) before the floor heating.
Pump operation and space heating and cooling
According to the season, the unit (1) will switch to either heating or cooling mode according to the temperature detected by the standard
controller (or optional wired controller (4)). When space heating/cooling is requested standard controller (or optional wired controller (4)), the
pump will start operating and the unit (1) will switch to heating mode/cooling mode. The unit (1) will operating to achieve the target cold/hot
water leaving temperature.
In the cooling mode. the motorized 2-way valve (14) will be set to closed to prevent cold water running through the floor heating loops (FHL).
CAUTION
When circulation in each fan coil units (FCU 1...3) is controlled by remotely controlled valves (M1...3), it is important to provide a
by-pass valve (15) to avoid the flow switch safety device from being activated. The pass-by valve should be selected as such that
at all time the minimum water flow. It is recommended to select a pressure difference controlled by-pass valve.
16
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KEM-14 DTN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KEM-14 DTN in the language / languages: English as an attachment in your email.

The manual is 7.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KEM-14 DTN

Kaysun KEM-14 DTN User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info