771401
26
Zoom out
Zoom in
Previous page
1/36
Next page
Cover
Screw
Page 26
If you will install the unit on the ground or on a
concrete mounting platform, do the following:
1. Mark the positions for four expansion bolts based on
dimensions chart.
2. Pre-drill holes for expansion bolts.
3. Place a nut on the end of each expansion bolt.
4. Hammer expansion bolts into the pre-drilled holes.
5. Remove the nuts from expansion bolts, and place
outdoor unit on bolts.
6. Put washer on each expansion bolt, then replace the
nuts.
7. Using a wrench, tighten each nut until snug.
WARNING
WHEN DRILLING INTO CONCRETE, EYE PROTECTION
IS RECOMMENDED AT ALL TIMES.
If you will install the unit on a wall-mounted bracket,
do the following:
CAUTION
Make sure that the wall is made of solid brick, concrete,
or of similarly strong material. The wall must be able to
support at least four times the weight of the unit.
1. Mark the position of bracket holes based on
dimensions chart.
2. Pre-drill the holes for the expansion bolts.
3. Place a washer and nut on the end of each expansion
bolt.
4. Thread expansion bolts through holes in mounting
brackets, put mounting brackets in position, and
hammer expansion bolts into the wall.
5. Check that the mounting brackets are level.
6. Carefully lift unit and place its mounting feet on
brackets.
7. Bolt the unit rmly to the brackets.
8. If allowed, install the unit with rubber gaskets to
reduce vibrations and noise.
Step 4: Connect signal and power cables
The outside unit's terminal block is protected by
an electrical wiring cover on the side of the unit. A
comprehensive wiring diagram is printed on the inside of
the wiring cover.
WARNING
BEFORE PERFORMING ANY ELECTRICAL OR
WIRING WORK, TURN OFF THE MAIN POWER TO
THE SYSTEM.
1. Prepare the cable for connection:
USE THE RIGHT CABLE
Indoor Power Cable (if applicable): H05VV-F or
H05V2V2-F
Outdoor Power Cable: H07RN-F
Signal Cable: H07RN-FF
CHOOSE THE RIGHT CABLE SIZE
The size of the power supply cable, signal cable, fuse,
and switch needed is determined by the maximum current
of the unit. The maximum current is indicated on the
nameplate located on the side panel of the unit. Refer to
this nameplate to choose the right cable, fuse, or switch.
a. Using wire strippers, strip the rubber jacket from
both ends of cable to reveal about 40mm (1.57in) of
the wires inside.
b. Strip the insulation from the ends of the wires.
c. Using a wire crimper, crimp u-lugs on the ends of
the wires.
PAY ATTENTION TO LIVE WIRE
While crimping wires, make sure you clearly distinguish
the Live ("L") Wire from other wires.
WARNING
ALL WIRING WORK MUST BE PERFORMED
STRICTLY IN ACCORDANCE WTH THE WIRING
DIAGRAM LOCATED INSIDE OF WIRE COVER OF
THE OUTDOOR UNIT.
2. Unscrew the electrical wiring cover and remove it.
3. Unscrew the cable clamp below the terminal block
and place it to the side.
4. Connect the wire according to the wiring diagram, and
rmly screw the u-lug of each wire to its corresponding
terminal.
5. After checking to make sure every connection is
secure, loop the wires around to prevent rain water
from owing into the terminal.
6. Using the cable clamp, fasten the cable to the unit.
Screw the cable clampd down tightly.
7. Insulare unused wires with PCV electrical tape.
Arrange them so that they do not touch any electrical
or metal parts.
8. Replace the wire cover on the side of the unit, and
screw it in place.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KAY-CF 71 DR8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KAY-CF 71 DR8 in the language / languages: English as an attachment in your email.

The manual is 3.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KAY-CF 71 DR8

Kaysun KAY-CF 71 DR8 User Manual - German - 36 pages

Kaysun KAY-CF 71 DR8 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info