771401
22
Zoom out
Zoom in
Previous page
1/36
Next page
Terminal block
Wire cover
Screw
Cable clamp
Space behind unit
Refrigerant piping
Insulation tape
Indoor unit
Signal wire Drain hose
Page 22
Minimum Cross-Sectional Area of Power
and Signal Cables (For reference)
Rated Current of
Appliance (A)
Nominal Cross-
Sectional Area (mm2)
> 3 y 6 0,75
> 6 y 10 1
> 10 y 16 1,5
> 16 y 25 2,5
> 25 y 32 4
> 32 y 40 6
CHOOSE THE RIGHT CABLE SIZE
The size of the power supply cable, signal cable, fuse,
and switch needed is determined by the maximum current
of the unit. The maximum current is indicated on the
nameplate located on the side panel of the unit. Refer to
this nameplate to choose the right cable, fuse, or switch.
1. Opent front panel of the indoor unit.
2. Using a screwdriver, open the wire box cover on the
right side of the unit. This will reveal the terminal block.
WARNING
ALL WIRING MUST BE PERFORMED STRICTLY
IN ACCORDANCE WITH THE WIRING DIAGRAM
LOCATED ON THE BACK OF THE INDOOR UNIT'S
FRONT PANEL.
3. Unscrew the cable clamp below the terminal block
and place it to the side.
4. Facing the back of the unit, remove the plastic panel
on the bottom left-hand side.
5. Feed the signal wire through this slot, from the back
of the unit to the front.
6. Facing the front of the unit, connect the wire according
to the indoor unit's wiring diagram, connect the u-lug
and rmly screw each wire to its corresponding
terminal.
CAUTION
DO NOT MIX UP LIVE AND NULL WIRES.
This is dangerous, and can cause the air conditioning unit
to malfunction.
7. After checking to make sure every connection is
secure, use the cable clamp to fasten the signal cable
to the unit. Screw the cable clamp down tightly.
8. Replace the wire cover on the front of the unit, andd
the plastic panel on the back.
NOTE ABOUT WIRING
THE WIRING CONNECTION PROCESS MAY DIFFER
SLIGHTLY BETWEEN UNITS AND REGIONS..
Step 7: Wrapping and cables
Before passing the piping, drain hose, and the signal cable
through the wall hole, you must bundle them together to
save space, protect them, and insulate them.
1. Bundle the drain hose, refrigeran pipes, and signal
cable as shown below..
DRAIN HOSE MUST BE ON BOTTOM
Make sure that the drain hose is at the bottom of the
bundle. Putting the drain hose at the top of the bundle can
cause the drain pan to overow, which can lead to re or
water damage.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KAY-CF 71 DR8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KAY-CF 71 DR8 in the language / languages: English as an attachment in your email.

The manual is 3.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KAY-CF 71 DR8

Kaysun KAY-CF 71 DR8 User Manual - German - 36 pages

Kaysun KAY-CF 71 DR8 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info