771400
28
Zoom out
Zoom in
Previous page
1/36
Next page
Flare nut
Copper pipe
Pipe
Flare form
Radius 10 cm (4 in)
Indoor unit tubing Flare nut Pipe
Page 28
4. Remove PVC tape from ends of pipe when ready to
perform aring work.
5. Clamp are form on the end of the pipe. The end of
the pipe must extend beyond the edge of the are
form in accordance with the dimensions shown in the
table below.
PIPING EXTENSION BEYOND FLARE
FORM
Outer Diameter of
Pipe (mm)
A (mm)
Min. Max.
Ø 6,35 (Ø 0,25") 0,7 (0,0275") 1,3 (0,05")
Ø 9,52 (Ø 0,375") 1,0 (0,04") 1,6 (0,063")
Ø 12,7 (Ø 0,5") 1,0 (0,04") 1,8 (0,07")
Ø 16 (Ø 0,63") 2,0 (0,078") 2,2 (0,086")
Ø19 (Ø 0,75") 2,0 (0,078") 2,4 (0,094")
6. Place aring tool onto the form.
7. Turn the handle of the aring tool clockwise until the
pipe is fully ared.
8. Remove the aring tool and are form, then inspect
the end of the pipe for cracks and even aring.
Step 4: Connect pipes
When connecting refrigerant pipes, be careful not to use
excessive torque or to deform the piping in any way. You
should rst connect the low-pressure pipe, then the high-
pressure pipe.
MINIMUM BEND RADIUS
When bending connective refrigerant piping, the minimum
bending radius is 10cm.
Instructions for Connecting Piping to
Indoor Unit
1. Align the center of the two pipes that you will connect.
2. Tighten the are nut as tightly as possible by hand.
1. Using a spanner, grip the nut on the unit tubing.
1. While rmly gripping the nut on the unit tubing, use
a torque wrench to tighten the are nut according to
the torque values in the Torque Requirements table
below. Loosen the aring nut slightly, then tighten
again.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun KAY-CF 52 DR8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun KAY-CF 52 DR8 in the language / languages: English as an attachment in your email.

The manual is 3.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun KAY-CF 52 DR8

Kaysun KAY-CF 52 DR8 User Manual - German - 36 pages

Kaysun KAY-CF 52 DR8 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info