771580
19
Zoom out
Zoom in
Previous page
1/23
Next page
Installation & Owner's Manual
16
Anode Rod
6.4 Error phenomenon shooting
Table.6-1
Error phenomenon Possible reason solution
Cold water
tapped out and
display screen
extinguished
Bad connection between power supply
plug and socket;
Setting water temperature too low;
Temp.sensor broken;
PCB of indicator broken.
Plug in;
Setting water temp. higher;
Contact service center.
No hot water
tapped out
Public water supply ceased;
Cold water inlet pressure too low (<0.15
MPa);
Cold water inlet valve closed.
Waiting for public water supply recover;
Waiting for inlet water pressure increase;
Open water inlet valve.
Water leakage Hydraulic pipeline joints are not sealed
well. Check and reseal all joints.
6.5 Error code shooting table
Table.6-2
Display Malfunction Description Corrective action
E0 Error of sensor T5U(upper water temperature sensor)
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
E1 Error of sensor T5L(lower water temperature sensor)
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
E2 Tank and Wired Controller communication error Maybe the connection between controller and PCB has
released or PCB has been broken.
E4 Evaporator temperature sensor T3 error
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
E5 Ambient temperature sensor T4 error
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
E6 Compressor discharge temperature sensor TP error
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
E8
Electric leakage error
If PCB currentjnductioncircuit check the current
difference between L,N >14mA, system consider it as
"electric leakage error"
Maybe some wires have been broken or bad wire
connection.
Contact a qualied person to service the unit.
E9 Compressor suction temperature sensor TH error
Maybe the connection between sensor and PCB has
released or sensor has been broken.
Contact a qualied person to service the unit.
EE E-heater open-circuit error(IEH (Current difference
E-heater on & E-heater off )<1 A)
Maybe the E-heater has been broken or bad wire
connection after repair.
EF Clock chip error
Maybe the chip has been broken, but unit can work well
without clock-menmory, so it is needed to reset clock
when power put on again.
If necessary, contact a qualied person to service the unit.
Ed E-EPROM chip error Contact a qualied person to service the unit.
P1 System high pressure protection
≥ 3.0MPa active: ≤ 2.4Mpa inactive
Maybe because of system blocked, air or water or more
refrigerant in system(after repair), water temperature
sensor malfunction, ect.
Contact a qualied person to service the unit.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun COMPAK KHP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun COMPAK KHP in the language / languages: English as an attachment in your email.

The manual is 2.84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info