772971

Kayoba-Jula 006372 Manual

28
Zoom out
Zoom in
Previous page
1/32
Next page
EN
28
FRONT WHEEL
1. Remove transport protection on the brake
calliper, in the form of a small piece of
plastic that separates the brake pads.
2. Put the wheel axle in the slots on the fork
legs and align the brake disc to the brake
calliper. Check that the wheel is straight,
in the middle of the fork legs.
3. Close the quick-release lock and rmly
tighten the adjusting nut on the opposite
side.
4. Open the quick-release lock, tighten the
adjusting nut another 3/4 turn, and then
close it again. Closing the quick-release
takes a little eort, so that it does not
open unintentionally and loosen the
wheel.
FIG. 5
SADDLE AND SADDLE POST
Grease the saddle post and insert it into the
saddle tube, and then lock to the required
height with the quick-release.
IMPORTANT:
It should not be possible to see the marking
for the top position on the saddle post.
PEDALS
The pedals are dierent and are therefore
marked with "L" (Left) and "R" (Right). If they
are tted on the wrong side or screwed in skew
in the crank arms this can damage the threads.
Grease the threads on the pedals before tting.
FIG. 6
Fitting the right-hand pedal (R)
Screw in the pedal clockwise on the chain side
of the crank arm and tighten with a 15 mm
13. Front gear
14. Pedal arm
15. Sprocket
16. Chain
17. Back gear
18. Back wheel
19. Back disc brake
20. Back reector
FIG. 1
ASSEMBLY
Suitable tools for assembly and adjustment.
• Combination spanners, sized 14 (2) and
15 mm
• Hex keys, size 4 and 5 mm
• Phillips screwdriver PH2
• Grease
HANDLEBARS
1. Unscrew the bracket on the stem with a 5
mm hex key.
FIG. 2
2. Put the handlebars on the stem. Make
sure that they are properly centred and
have a suitable angle for the handbrake
and gear lever, and that the brake and
gear wires are on the right sides of the
frame and front fork. If the wires are not
properly positioned the handlebars or
fork has turned, and must be turned back
before tting the handlebars.
FIG. 3
3. Screw together the bracket and tighten
the two hex screws alternately.
FIG. 4
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kayoba-Jula 006372 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kayoba-Jula 006372 in the language / languages: English, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 2.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info