63824
92
Zoom out
Zoom in
Previous page
1/92
Next page
TROUBLESHOOTING
In the event of a malfunction, rst check all the cable connections and operating states:
1. Receiver and TV set power plugs are connected to wall socket
2. Antenna cables on receiver input
3. Receiver and TV set correctly connected by a Scart or cinch cable
4. Audio connections are made to Hi-Fi or Dolby Digital system as appropriate
5. Receiver and TV set (Hi-Fi/Dolby Digital system) are switched on (check power indicators)
6. Receiver is responding to remote control
A selection of troubleshooting tips is offered below.
Problem Cause Remedy
“No or bad signal!” warning
appears on some or all channels
Antenna signal of satellite
reception system missing or
faulty. Incorrect LNB frequencies
set in “Antenna Con guration”
menu.
Consult an antenna specialist to
have it checked and repaired as
necessary. On “Installation”menu
check LNB con guration
for the satellite in question:
High L.O. “10,600” GHz, Low L.O.
“9,750” GHz, and Limit frequency
L.O. “11,700 MHz”, and change
as necessary.
Remote control no longer
responding
Receiver or remote control
command set may have been
unintentionally changed
Set infrared code 1, as described
in operating manual under
“Remote Control RC 660”; check
batteries
Wrong time being displayed
“Summer Time” setting wrong.
An incorrect time was imported
from the reception signal
On “Settings” - „Date and Time
Setup“ menu check “Summer
Time Enabled” and change as
necessary Switch off receiver
at mains switch from current
channel, e.g. ARD or ZDF,
wait 10 seconds and then switch
back on
The following channels cut out
or “No or bad signal!” appears:
PRO 7, SAT1, Cable 1, DSF,
N 24, Tele 5, 9 Live, HSE 24 and
Sonnenklar TV
DECT telephones operate on
the same frequency as these
channels. Interference may occur
due to inadequate level or poor
shielding of cable
Consult your antenna specialist
Black or blue screen, no on-
screen displays
Scart connection to TV
deactivated by accidentally
pressing the 0 button
Keep pressing the 0 button
until the TV picture reappears
on-screen
Videotext cannot be called up
using the TV set remote control
The Videotext signal is not
being transmitted over the HDMI
interface. The HDMI standard
de nitions do not provide for
transmission of Videotext
Call up Videotext by pressing
the
button on the receiver
remote control, as described in
the chapter “Videotext”
Internet: http://www.kathrein.de
KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3
P.O. Box 100 444 • 83004 Rosenheim GERMANY
936.3095/D/1108/ZWT - Technical data subject to change.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein UFS 910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein UFS 910 in the language / languages: English as an attachment in your email.

The manual is 3,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein UFS 910

Kathrein UFS 910 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info