631819

Kathrein CAP 301 - MobiSet 3 digital Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
CAP 200 and 301/HDP 170
Short User Guide
936.2412/D/0604/2.2e/ZWT - Technical data subject to change!
Possible fault messages and their causes
1. Initalisation OSD does not disappear (not even after 20 se-
conds)
Check the connection between receiver and control unit
Control in the main menu if the HDP mode (antenna
positioning) on the receiver was switched off
2. Satellite could not be found
Try the search once more but with a different programme of the
same satellite
The OK-button allows you to exit from the OSD insertion and
the search fo a new programme. If required, use the F button
3. The satellite signal was lost (e.g. possibly due to unfavourab-
le reception conditions)
Repeat the search with the same or a different programme of
the same satellite
Pressing the OK-button allows exit from the OSD insertion and
the selection of a new programme. If required use the F-button
•
•
•
•
•
4. Voltage supply is too low
Your positioner is still operational, but too low voltage supply
can cause an overload
5. Overload exists
If this message appears, check the vehicle‘s voltage (possibly
too low), the connection with the positioner, possible icing of the
positioner or the positioner is blocked due to an obstacle
Switch off the receiver, then switch it on again (this procedure
must be repeated several times, if necessary). Refer in this con-
nection also to point 11 of the user manual for BAS 60,
functional disturbances
•
•
•
Power-off/Stand-by/Parking position
Switch off the receiver with the mains switch (Power-off)
The receiver is separated from the mains, the control unit automatically switches to the stand-by mode, and the HDP
remains in its satellite position until the receiver is switched on again.
Stand-by
Pressing the stand-by button once, switches receiver and control box to the stand-by mode. The HDP behaves the same
as in mode „Power-Off“ (see above).
Parking position
Pressing the stand-by button twice causes the HDP to move automatically into the parking position, whereas the control
unit and the receiver swith to stand-by mode. After the receiver is switched on again, the HDP moves to its last satellite
position. More detailed information as to moving the HDP into the parking position is found in the unabridged manual.
•
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein CAP 301 - MobiSet 3 digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein CAP 301 - MobiSet 3 digital in the language / languages: English, German as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein CAP 301 - MobiSet 3 digital

Kathrein CAP 301 - MobiSet 3 digital Installation Guide - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info