724852

Karcher WD 3 Battery Manual

18
Zoom out
Zoom in
Previous page
1/274
Next page
– 9
몇CAUTION
Safety installations serve the protection of the user
and may not be modified or bypassed.
The installed protective circuit protects the battery pack
against
Overheating
Full discharge
Overcharging
Short-circuit
Figure dependent on types
1Nameplate
2 Display
3Contacts
4 Intake
1 Battery contacts
2 Battery adapter
3 Connection cable
4Nameplate
5 Plug-in power supply
몇CAUTION
Risk of injury, risk of damage! Observe the operating in-
structions and safety instructions of the charger.
Note
New battery packs are only pre-charged and must be
fully charged before first use.
The display is activated during the first charging pro-
cess.
To ensure that the charge level indicator works correct-
ly, the battery pack must be discharged during initial use
until the device is switched off.
Illustration
Plug the plug-in power supply into the socket.
Push the battery pack into the battery adapter of
the charger.
The charging process begins automatically.
Illustration
The remaining charging time is displayed on the
battery pack display.
The charging time with a standard charger (Battery
Power BC 36 V) for an empty battery pack (Battery
Power 36/25) is approx. 5,5 hours.
When the battery pack is fully charged, the display
shows 100%.
Remove the battery adapter from the battery pack
after charging.
Pull the plug-in power supply from the socket.
Note
If the display does not show anything when the battery
pack is in the charger, the battery capacity is fully de-
pleted or very low. As soon as the battery pack has
been sufficiently charged, the display shows the re-
maining charging time.
If the display does not show anything even after a
long period of time, the battery pack is defective
and must be replaced.
Note
New battery packs reach their full capacity after approx.
5 charging and discharging cycles.
Charge batteries that have not been used for a long time
before use.
The performance of the battery pack is reduced at tem-
peratures below 0°C.
The capacity of the battery pack may be reduced if
stored at temperatures over 20°C.
Note
The charged battery pack can remain on the charger till
it is to be used. There is no risk of over-charging.
In order to avoid unnecessary energy consumption, the
charger should, however, be unplugged as soon as the
battery pack has been fully charged.
The battery pack is equipped with a display that
provides continuous information on the charging
state, the progress of charging and the remaining
battery life. In addition, any error messages occur-
ring will also be shown.
The runtime adjustment is generated via capacity
switching.
Depending on the device used, the display rotates
when the battery pack is inserted.
Safety Devices
Protective circuit
Operating elements
Battery pack
Standard charger
Charging process
Battery pack operation
Display
18 EN
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher WD 3 Battery at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher WD 3 Battery in the language / languages: All languages as an attachment in your email.

The manual is 18,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info