803801
12
Zoom out
Zoom in
Previous page
1/148
Next page
12 English
Technical data
Subject to technical modifications.
Optimising the flow rate
The flow rate is further increased:
The lifting height is reduced.
The diameter of the hose used is increased.
The length of the hose used is decreased.
The smaller the pressure loss caused by the con-
nected up accessories.
Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Pump
Type: 1.645-xxx
Fault Cause Rectification
The pump is running, but
not delivering
Air is in the pump. 1. Pull the mains plug out of the socket and
plug it in again several times, until the fluid
is drawn in.
The suction area is clogged. 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The fluid level is too low in manual oper-
ation.
1. Immerse the pump deeper into the feed flu-
id if possible, see chapter Operation.
The pump does not start
up, or stops suddenly
during operation
The power supply is disconnected. 1. Check the fuses and the electrical connec-
tions.
The thermal protection switch has
switched off the pump because of over-
heating.
1. Pull the mains plug out of the socket.
2. Allow the pump to cool down.
3. Remove any dirt particles in the suction ar-
ea.
4. Clean the suction area.
5. Prevent the pump from running dry.
Dirt particles block the suction area. 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The pumping capacity
decreases
The suction area is clogged. 1. Pull the mains plug out of the socket.
2. Clean the suction area.
The delivery rate is too
low
The maximum delivery head is exceed-
ed.
The hose diameter and the hose length
have been selected incorrectly.
1. Observe the maximum delivery head, see
chapter Technical data.
2. If necessary, select a greater hose diame-
ter or a shorter hose length, see chapter
Optimising the flow rate.
Quick-Connect cannot
be opened or closed
The push-fit system is dirty. 1. Remove the clip.
2. Clean the clip.
3. Install the clip.
SP
16.000
Dirt
SP
22.000
Dirt
Device performance data
Mains voltage V 230-240 230-240
Power frequency Hz 50 50
Nominal power W 550 750
Maximum flow rate l/h 16,000 22,000
Pressure (max.) MPa
(bar)
0.08
(0.8)
0.08
(0.8)
Delivery height (max.) m 8 8
Immersion depth (max.) m 7 7
Perm. temp. feed fluid °C 5...35 5...35
Particle size (max.) of per-
missible feed fluids
mm 20 30
Minimum fluid level (manu-
al mode)
mm 60 50
Residual fluid height mm 25 35
Weight (without accesso-
ries)
kg 4.9 6.5EU Declaration of Conformity
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher SP 22.000 Dirt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher SP 22.000 Dirt in the language / languages: All languages as an attachment in your email.

The manual is 3.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info