477952
13
Zoom out
Zoom in
Previous page
1/64
Next page
To separate the machine from the
mains, pull the plug and not the power
cord.
Do not scrape the power cord across
sharp edges and ensure that it does not
get pressed.
The voltage indicated on the type plate
must correspond to the voltage of the
electrical source.
To avoid risks, all repairs and replace-
ment of spare parts may only be carried
out by the authorised customer service
personnel.
Follow the rules for electrical safety of
equipment:
When pumping out swimming pools,
garden ponds and fountains, only using
a earth-leakage circuit breaker with a
nominal leakage current of max. 30 mA
with the immersion pump. Do not oper-
ate the pump if there are persons locat-
ed in the swimming pool or the garden
pond.
For safety reasons, we recommend that
you operate the appliance only via a
earth-leakage circuit breaker (max. 30
mA).
The machine should only be operated
with a power source with proper earth-
ing and connected safety conductors.
The electrical connection of the system
may only be performed by a qualified
electrician. Please follow the respective
national regulations!
This device is not intended for use by
persons (including children) with re-
duced physical, sensory or mental abil-
ities or lacking experience and/or
knowledge, unless they are supervised
by a person responsible for their safety
or are instructed by these persons on
the use of the device. Children should
be supervised, to ensure that they do
not play with the device.
Please follow the safety instructions before
start-up!
Please keep in mind that the label "100%
tested" may not be removed from the
pump. If the label is removed, there will be
no more warranty for the tightness of the
pump.
1 Power cord with plug
2 Level Sensor
3 Ventilation button
4 Carrying handle
5 Hose connection 1“ (25.4 mm) und 1
1
/
2
(38 mm)
6Flat seal
7 Backflow valve
8 Cable connector
Illustration
For a 1
1
/
2
“ (38mm) hose, the hose con-
nection must first be sawed off.
Illustration
Place the flat seal into the hose connec-
tion piece.
If you would like to prevent the water
that is standing in the hose or above the
pump after the pump has been turned
off, we recommend that you use the in-
cluded backflow valve. Before inserting
the backflow valve, the flat seal must be
removed. Pay attention to correct posi-
tioning.
Screw the hose connection on to the
pump
Push the hose on the hose connection
and fasten it with appropriate hose clip
Note:
The larger the hose diameter and the short-
er the hose, the higher the feed rate.
Start up
Description of the Appliance
Preparing the Appliance
English 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher SCP 12000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher SCP 12000 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info