724889

Karcher SC 3 Upright EasyFix Manual

14
Zoom out
Zoom in
Previous page
1/188
Next page
14 English
3. Drain the water reservoir.
Illustration U
Storing the device
ATTENTION
Material damage due to condensate/moisture
The floor covering can be damaged by moisture remain-
ing on the floor cleaning cloth or floor nozzle/device af-
ter cleaning.
Remove the floor cleaning cloth/carpet glider and dry
the floor nozzle/the device after finishing the floor clean-
ing work.
Do not place or store the device on heat-sensitive sur-
faces.
1. Remove the floor cleaning cloth or floor cleaning
cloth and carpet glider, see the chapter Floor nozzle
and carpet glider.
Illustration D
Illustration E
2. Remove moisture from the floor nozzle/device.
3. Wind the power cable around the upper and lower
cable hooks.
Illustration V
4. Store the device in vertical position on a solid base
or on the wall.
Illustration I
5. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
Cleaning coated or painted surfaces
ATTENTION
Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings
or paint and edge band from edges.
Do not direct the steam at glued laminated edges as the
edge band may loosen.
Do not use the device for cleaning unsealed wood or
parquet floors.
Do not use the device for cleaning painted or plastic
coated surfaces such as kitchen or living room furniture,
doors or parquet.
How to use the Accessories
Floor nozzle
The floor nozzle is suitable for cleaning washable floor
coverings, e.g. stone floors, tiles and PVC floors, and al-
so sealed wooden floors such as parquet and laminate.
ATTENTION
Damage due to steam effects
Heat and the effects of steam can lead to damage.
Check the heat resistance and steam effect on an in-
conspicuous area using a minimal steam volume prior
to use.
Steam clean sealed wooden floors using the correct,
preset steam level and do not remain in the same posi-
tion on the floor for too long
Note
Detergent residue or care emulsions on the surface to
be cleaned can lead to streaks during steam cleaning,
which will disappear however once these have been
used several times.
몇CAUTION
Beware of burns to your feet
The floor nozzle/floor cleaning cloth heats up during
steaming.
Hot water may drip out when pulling off the floor cloth.
Only operate or remove the floor nozzle/floor cleaning
cloth with suitable footwear.
1. Fasten the floor cleaning cloth to the floor nozzle.
a Place the floor cleaning cloth with the hook and
loop fastener strips pointing upwards on the floor.
b Place the floor nozzle onto the floor cleaning
cloth, applying slight pressure.
Illustration D
The floor cleaning cloth will stick to the floor nozzle
of its own accord due to the hook and loop fastener.
Micro fibre cloth
The microfibre floor cloth is suitable for cleaning stone
floors and PVC floors, and also sealed wooden floors
such as parquet and laminate. The microfibre floor cloth
is also suitable for freshening carpets when used in con-
junction with the carpet glider.
Abrasive floor cloth
The abrasive floor cloth is suitable for cleaning insensi-
tive surfaces such as tiles or stone.
ATTENTION
Damage to floor coverings
The abrasive floor cloth can damage sensitive floor cov-
erings and surfaces.
Do not use the abrasive floor cloth for cleaning wooden
surfaces.
Do not use the abrasive cloth with the carpet glider.
Removing the floor cleaning cloth
1. Place one foot on the bottom corner of the floor
cleaning cloth and lift the floor nozzle up.
Illustration D
Note
Initially, the floor cleaning cloth's hook and loop fas-
tener strip is very strong and cannot be removed
from the floor nozzle easily. After the floor cleaning
cloth has been used several times and washed, it is
easier to remove from the floor nozzle and it has
reached the optimum adhesion.
Removing the floor nozzle from the basic device
ATTENTION
Material damage due to an unstable device
Removing the floor nozzle makes the device unstable
and it can tip over and damage the device and floor cov-
ering.
Do not remove the floor nozzle from the basic device af-
ter installation.
Remove the floor nozzle only when sending the device
for servicing.
1. Press the OFF switch
Illustration S
2. Pull the mains plug out of the socket.
Illustration T
3. Empty the water reservoir.
Illustration U
4. Hold the device by the handle.
5. Actuate the unlocking button on the floor nozzle.
6. The floor nozzle releases from the device and can
be removed.
Illustration W
7. Store the device safely in a horizontal position.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher SC 3 Upright EasyFix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher SC 3 Upright EasyFix in the language / languages: All languages as an attachment in your email.

The manual is 13,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info