Manual Karcher SC 3 EasyFix (page 14 of 186) (All languages)

724884

Zoom out

Zoom in

1/186

14 English

Spotlight nozzle

The spotlight nozzle is suitable for cleaning areas, joins,

fittings, drains, sinks, WCs, blinds or radiators that are

difficult to access. The closer the spotlight nozzle is to

the soiled area, the greater the cleaning efficiency will

be as the temperature and steam volume are at their

highest at the nozzle opening. Larger lime deposits can

be treated before steam cleaning with a suitable deter-

gent. Allow the detergent to soak in for

approx. 5 minutes and then steam it off.

1. Slide the spotlight nozzle onto the steam gun.

Illustration H

Round brush (small)

The small round brush is used for cleaning stubborn dirt.

Stubborn dirt can be removed more easily by brushing.

ATTENTION

Damaged surfaces

The brush may scratch sensitive surfaces.

It is not suitable for cleaning sensitive surfaces.

1. Fit the round brush to the spotlight nozzle.

Illustration I

Round brush (large)

The large round brush is suitable for cleaning large

rounded surfaces, e.g. wash basin, shower tray, bath

tub, kitchen sink.

ATTENTION

Damaged surfaces

The brush may scratch sensitive surfaces.

It is not suitable for cleaning sensitive surfaces.

1. Fit the large round brush to the spotlight nozzle.

Illustration I

Power nozzle

The power nozzle is used for cleaning stubborn dirt,

blowing down corners, joins etc.

1. Install the power nozzle onto the spotlight nozzle ac-

cording to the round brush.

Illustration I

Manual nozzle

The manual nozzle is used for cleaning small areas that

can be washed down, shower cubicles and mirrors.

1. Push the manual nozzle onto the steam gun accord-

ing to the spotlight nozzle.

Illustration H

2. Pull the cover over the manual nozzle.

Floor nozzle

The floor nozzle is used for cleaning washable wall and

floor coverings e.g. stone floors, tiles and PVC floors.

ATTENTION

Damage due to build-up of steam

Heat and moisture can lead to damage.

Check the heat resistance and steam effect on an in-

conspicuous area using a minimal volume of steam pri-

or to use.

Note

Detergent residue or care emulsions on the surface to

be cleaned can lead to streaks during steam cleaning,

which will disappear however once these have been

used several times.

We recommend sweeping the floor or vacuum cleaning

it before using the device. In this way the floor will be

cleared of dirt and loose particles before the wet clean-

ing commences. Work slowly on surfaces that are heav-

ily soiled so that the steam has longer to take effect.

1. Connect the extension tubes with the steam gun.

Illustration J

2. Push the floor nozzle onto the extension tube.

Illustration K

3. Fasten the floor cleaning cloth to the floor nozzle.

a Place the floor cleaning cloth with the hook and

loop fastener strips pointing upwards on the floor.

b Place the floor nozzle onto the floor cleaning

cloth, applying slight pressure.

Illustration L

The floor cleaning cloth will stick to the floor nozzle

of its own accord due to the hook and loop fastener.

Removing the floor cleaning cloth

1. Place one foot on the bottom corner of the floor

cleaning cloth and lift the floor nozzle up.

Illustration L

Note

Initially, the floor cleaning cloth's hook and loop fas-

tener strip is very strong and cannot be removed

from the floor nozzle easily. After the floor cleaning

cloth has been used several times and washed, it is

easier to remove from the floor nozzle and it has

reached the optimum adhesion.

Parking the floor nozzle

1. Hang the floor nozzle in the park bracket during

breaks in work.

Illustration Q

Carpet glider

The carpet glider is used for freshening up carpets.

ATTENTION

Beware of damaging the carpet glider and carpet

Contamination on the carpet glider, as well as heat and

moisture penetration, can result in the carpet being

damaged.

Prior to the application, also check the heat resistance

and impact of steam on the carpet at an insignificant

spot using as small an amount of steam as possible.

Observe the cleaning instructions from the carpet man-

ufacturer.

Prior to using the carpet glider, make sure that the car-

pet has been vacuumed and that stains have been re-

moved.

Prior to application and following operating pauses, re-

move any possible water accumulation (condensate) in

the appliance by means of evaporating the condensate

into a drain (without floor cleaning cloth / with accesso-

ries).

Only use the carpet glider with a floor cleaning cloth on

the floor nozzle.

Steam clean with a weak steam stage when using the

carpet glider.

In order to prevent too much moistening and to avoid

the risk of damage due to temperature effects, do not di-

rect the steam continuously onto one spot (maximum

5 seconds).

Do not use the carpet glider on deep-pile carpets.

Fastening the carpet glider to the floor nozzle

1. For fastening the floor cleaning cloth to the floor

nozzle, please refer to chapter Floor nozzle.

Illustration L

2. Using a little force, allow the floor nozzle to slide into

the carpet glider and engage there.

Illustration M

3. Start cleaning the carpet.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher SC 3 EasyFix in the language / languages: All languages as an attachment in your email.

The manual is 9,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher SC 3 EasyFix Manual

Product: