804557
8
Zoom out
Zoom in
Previous page
1/88
Next page
8English
Using the additional socket
1. Open the protective cover of the additional socket.
2. Plug the unit plug of the PW 30/1 into the additional
socket of the Puzzi washing vacuum.
3. Put PW 30/1 into operation.
Operation
Switching on the device
1. Put the Puzzi washing vacuum into operation.
2. Start the brush drive on the power switch of the PW
30/1.
Illustration E
Note
When the brush is blocked, the brush drive switches off.
For remedy see troubleshooting guide.
Cleaning
1. Operate the valve handle. This is used to spray on
the detergent solution. The waste water is immedi-
ately vacuumed back in via the suction nozzle.
Illustration F
2. For cleaning, pull PW 30/1 backwards over the car-
pet in slightly overlapping paths. Start in such a way
that areas that have already been cleaned do not
have to be walked on again.
3. Release the valve handle when moving forward (idle
stroke).
Switching off the device
1. Switch off the brush drive at the power switch.
2. Set the Puzzi washing vacuum out of operation.
Transport
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Pull the device behind you with the suction pipe
when transporting it over longer distances.
2. Carry the device by the casing and suction pipe.
3. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
Care and maintenance
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Unplug the unit.
Maintenance intervals
Each time after use
1. Rinse PW 30/1 with clear water.
2. Clean the roller brush of lint and dirt.
3. Check the spray pattern of the nozzle mouthpiece; if
the spray pattern is uneven, clean the nozzle and
mouthpiece.
4. Clean the suction hose and suction nozzles when
the suction performance decreases.
Half-yearly
1. Check toothed belt wear and tension, replace
toothed belt if necessary.
2. Check brush wear, replace brush if necessary.
Maintenance work
Replacing the roller brush
1. Release 5 screws and remove the cover.
2. Remove the toothed belt.
3. Unscrew the screw on the front of the brush.
4. Dismantle the retaining plate on the opposite side by
loosening 3 screws and remove the brush.
5. Installation of the brush is performed in the reverse
sequence.
Troubleshooting guide
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Unplug the unit.
Brush is blocked
Note
When the brush is blocked, the brush motor is switched
off.
1. Check brush for dirt and remove any blocking ob-
jects if necessary.
2. Unscrew the protective cover and press the fuse
switch using a screwdriver. Screw the protective
cover back in.
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.
Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Spray extraction device
Type: 1.913-xxx
EU Declaration of Conformity
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher PW 30-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher PW 30-1 in the language / languages: All languages as an attachment in your email.

The manual is 3.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info