725102

Karcher PSW 18-20 Battery Manual

19
Zoom out
Zoom in
Previous page
1/248
Next page
English 19
13 Handle
14 Battery pack trigger
15 Type plate
16 Trigger
17 Trigger lockout button
18 Carrying belt
19 Allen key for adjusting the chain tension
20 Bar scabbard
21 Chain oil
22 *Battery Pack Battery Power 18V
23 *Quick Charger Battery Power 18V
* optional
Rechargeable battery pack
The device can be operated with a 18 V Kärcher Bat-
tery Power battery pack.
Initial startup
Installing shaft
If required, the device can be extended with the includ-
ed extension insert.
1. Connect the lower shaft and the extension insert.
Illustration B
2. Connect the upper shaft and the extension insert.
Inserting the carrying belt
The carrying belt helps to lower the device in a con-
trolled manner after cutting and to catch the weight of
the device during use.
Illustration C
1. Hook the carrying belt hooks into the eyelets on the
handle and shaft. Place the carrying belt over one
shoulder. Make sure that the carrying belt can be re-
leased quickly in the event of danger.
Filling the chain oil tank
1. If necessary, clean the area around the filling hole of
sawdust and dirt.
2. Remove the chain oil tank cap.
Illustration D
3. Fill the chain oil into the tank. Check the filling level
of the chain oil on the sight glass and make sure that
the chain oil tank is filled to the maximum below the
filling hole.
Illustration E
4. Wipe up any spilled chain oil with a cloth.
5. Close the chain oil tank cap.
Checking the chain tension
몇 CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
1. Remove the bar scabbard.
Illustration F
2. Carefully pull on the chain.
Illustration G
The distance between the guide rail and the chain
must be 3-4 mm.
3. If necessary, adjust the chain tension (see Chapter
Adjusting the chain tension).
Installing the battery pack
1. Push the battery pack into the mounting in the de-
vice until it audibly latches into place.
Illustration H
Operation
Basic operation
1. Examine the tree and branches for damage such as
rot.
In the case of damaged or rotten branches, seek the
advice of a professional arborist.
2. Remove the bar scrabber.
3. Hold the device firmly with both hands.
Switch on the device
1. Press the trigger lockout button.
Illustration I
2. Press the trigger.
The device starts up.
3. Release the trigger.
The device stops.
Working techniques
When pruning, proceed as follows:
Place the bar on the branch to be cut and push the
device forward so that the end stop touches the
branch.
Illustration J
The device stabilizes during pruning and the cuts
are made cleaner.
Where possible, maintain a distance of approx. 15
cm between the tree trunk and the cut.
Cut small branches that are thin and light a single
cut with the bottom edge of the guide rail.
Heavier branches of larger diameter may break or
splinter during pruning. Therefore, cut in several
steps:
a Make a cut in the underside of the branch with the
top edge of the guide rail. This cut should be
about one third of the branch diameter.
Illustration K
b Make a cut in the top of the branch.
c If another cut is necessary, never continue cutting
in an existing cut but rather start a new cut.
The following should be noted when pruning:
Do not raise the bar higher than 60 ° from the hori-
zontal.
Do not exert excessive force on the guide rail.
Do not stand under the branch being sawn off.
Make sure that the falling branch does not endanger
the user or spectators nor damage any objects.
Maintain a safety distance of at least twice the
branch length when pruning. If this is not possible,
have the work done by a professional arborist.
Removing the battery pack
Note
During longer work breaks, remove the battery pack
from the device and secure it against unauthorised use.
1. Press the battery pack unlocking button to unlock
the battery pack.
Illustration L
2. Remove the battery pack from the device.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher PSW 18-20 Battery at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher PSW 18-20 Battery in the language / languages: All languages as an attachment in your email.

The manual is 20,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info