Manual Karcher KM 70-30C Bp (page 11 of 148) (All languages)

804781

Zoom out

Zoom in

1/148

- 4

Check the sealing strips in the sweep-

ing area for wear.

Half-yearly maintenance:

Check tension, wear and tear and func-

tioning of the drive belts.

Maintenance following wear:

Replace sealing strips.

Replace roller brush.

Replace side brush.

For description, see section on Mainte-

nance work.

NOTICE

Where maintenance is carried out by the

customer, all service and maintenance

work must be undertaken by a qualified

specialist. If required, a specialised Kärch-

er dealer may be contacted at any time.

Park the sweeper on an even surface.

Turn the program selection switch to

"OFF".

Loosen 3 fastening screws.

Replace side brushes and tighten the

screws.

It is necessary to replace them if the sweep

results are visibly poorer due to wear and

tear of the brushes and it is not possible to

readjust them using "Lever contact pres-

sure of sweep roller".

Remove the waste container.

Figure 8, see cover page

Pull the lever for contact pressure of

sweep roller fully backwards.

Loosen 3 screws each on both the

sides of the sweep roller.

Separate the roller halves and remove

them.

Place new roller halfs on the sweep roll-

er shaft. Ensure that the pins are sitting

correctly.

Fix in the screws and tighten them.

Loosen the screws as shown in the re-

spective diagram.

Remove the sealing strip and replace it

with a new sealing strip.

Fix in the screws and tighten them.

Front sealing strip (at the waste contain-

er)

Figure 9, see cover page

Rear sealing strip

Figure 10, see cover page

Side sealing strips

Figure 11, see cover page

Pull the handle of the filter shake-off

many times and release it.

Tilt the dust suction upward.

Figure 12, see cover page

Lift out the flat-fold filter and insert a

new flat-fold filter.

Remove both the foam filters.

Clean the foam filters under flowing wa-

ter and let them dry.

Push in the foam filters into the casing.

Ensure that the foam filters are gap-free

on all sides.

DANGER

Risk of injury!

Prior to performing any tasks on the de-

vice, turn the programme selector

switch to "OFF“and disconnect the ca-

ble from the negative terminal of the

battery.

Maintenance Works

Replacing side brush

Replacing roller brush

Replace the sealing strips

Replace flat fold filter (only Adv. model).

Cleaning the flat-fold filter

Special accessories

Roller-brush, soft

Order no. 6.903-995.0

For fine dust on all surfaces, exterior and

interior areas (wetness-resistant)

Roller-brush, hard

Order no. 6.903-999.0

To remove sticky contamination in exterior

areas

Roller brush, antistatic

Order no. 6.907-023.0

For statically chargeable surfaces such as

carpet or artificial turf

Faults

Fault Remedy

Appliance cannot be started Check fuse; replace it, if required *

Check battery; charge it, if needed

Machine is not sweeping properly Check roller brush and side brushes for wear, replace if necessary.

Check the pad for wear, replace if required.

Dust gathers in the machine Empty waste container

Check dust filter - clean or replace it (only Adv. model)

Do not rinse out the dust filter.

Check the pad for wear, replace if required.

Poor cleaning performance at edges Replace side brush

Check the pad for wear, replace if required.

Inadequate sweep performance (only Adv. model). Check filter case seal

Check washers of the dust suction

Roller brush does not turn. Remove belts or cords from roller brush.

Reducing the sweeping area: Set lever for roller brush contact pressure in the “–”

direction.

11EN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher KM 70-30C Bp in the language / languages: All languages as an attachment in your email.

The manual is 4.17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher KM 70-30C Bp Manual

Product: