Manual Karcher K 5 Premium Smart Control (page 19 of 200) (All languages)

803266

Zoom out

Zoom in

1/200

English 19

Clean the sieve in the water connection

ATTENTION

Damaged sieve in the water connection

Damage to the device through contaminated water

Check the sieve for damage before inserting it in the wa-

ter connection.

If necessary, clean the sieve in the water connection.

1. Remove the water connection coupling.

2. Pull the sieve out using flat pliers.

3. Clean the sieve under running water.

Illustration V

4. Insert the sieve into the water connection.

Replacing the batteries of the high-pressure

gun

Two non-rechargeable or rechargeable AAA batteries

are required.

The batteries are exhausted if nothing or a flashing bat-

tery symbol is visible in the display of the high-pressure

gun.

Illustration W

1. Press the locking slide.

Illustration X

2. Open the battery compartment.

3. Remove the battery.

4. Insert new batteries, while paying attention to the

correct alignment of the poles.

5. Close the battery compartment.

6. Dispose of the used batteries in accordance with

statutory provisions.

Troubleshooting guide

Malfunctions often have simple causes that you can

remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned

here, please contact your authorised Customer Service.

DANGER

Danger of electric shock

Injuries due to touching live parts

Switch off the device.

Remove the mains plug.

Device not running

1. Press the lever of the high-pressure gun.

The device switches on.

2. Check that the voltage specified on the type plate

corresponds to the voltage of the power source.

3. Check the mains connection cable for damage.

4. If the motor is overloaded and the motor circuit

breaker has triggered:

a Switch off the device "0/OFF".

b Allow the device to cool down for 1 hour.

c Switch the device on "I/ON" and resume opera-

tion.

Have the device checked by Customer Service if

this fault occurs repeatedly.

The device does not start up, the motor buzzes

Voltage drop due to a weak mains grid or when using an

extension cable

1. When switching on, first press the lever on the high-

pressure gun and then switch on the device "I/ON".

Device does not reach required pressure

The water supply is too low

1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.

The sieve in the water connection is dirty.

1. Pull the sieve in the water connection out using flat

pliers.

2. Clean the sieve under running water.

Air is in the device.

1. Vent the device:

a Switch on the device without a connected spray

lance for a maximum of 2 minutes.

b Press the high-pressure gun and wait until the

water escaping from the high-pressure gun is

free of air bubbles.

c Connect the spray lance.

d Observe the maximum suction height during suc-

tion operation (see chapter Technical data).

Strong pressure fluctuations

1. Clean the high-pressure nozzle:

a Use a needle to remove dirt from the nozzle drill.

b Rinse the high-pressure nozzle from the front

with water.

2. Check the water supply volume.

Device leaking

1. The device leaks a small amount for technical rea-

sons. If the leak is severe, request authorised Cus-

tomer Service.

Detergent is not sucked in

1. Turn the 3-in-1 Multi Jet spray lance to detergent

nozzle "MIX".

2. Check that the Plug ‘n’ Clean detergent bottle is sit-

ting correctly with the opening facing down in the de-

tergent connection.

No pressure indicator on the high-pressure gun

Illustration Y

1. Re-establish the connection to the high-pressure

cleaner, see chapter Initial Start-Up.

BOOST function is not shown on the display and

cannot be started via the KÄRCHER Home & Garden

app

The device is overheated.

1. Check the water supply temperature (for maximum

water inlet temperature, see chapter Technical da-

ta).

2. Reduce the water supply temperature to give the

motor more cooling.

Error messages

Illustration Z

1. Switch off the device "0/OFF".

2. Pull the mains plug out of the socket.

3. After 20 seconds, insert the mains plug back into the

socket.

4. Switch the device on "I/ON".

Have the device checked by Customer Service if

this fault occurs repeatedly.

Emergency operation

If the pressure regulation on the high-pressure gun is

defective, the high-pressure cleaner works at maximum

level.

1. Deactivating emergency operation:

a Switch off the device "0/OFF".

b Pull the mains plug out of the socket.

c After 20 seconds, insert the mains plug back into

the socket.

d Switch the device on "I/ON".

Have the device checked by Customer Service if

this fault occurs repeatedly.

The high-pressure gun is not working properly

Illustration AA

An internal error has occurred in the electronics of the

high-pressure gun.

1. Press the locking slide.

Illustration X

2. Open the battery compartment.

3. Remove the battery.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher K 5 Premium Smart Control in the language / languages: All languages as an attachment in your email.

The manual is 11.94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher K 5 Premium Smart Control Manual

Product: