726223
20
Zoom out
Zoom in
Previous page
1/252
Next page
– 6
Take out sieve.
Clean sieve in water and reinstall.
Unpressurize the appliance.
Unscrew the fine filter from the boiler.
Remove the fine filter and the filter insert.
Clean the filter with clean water or compressed air.
Reinstall in reverse sequence.
Unpressurize the appliance.
Loosen covering nut and take off hose.
Take out sieve.
Note: If necessary turn in screw M8 appr. 5 mm inwards
and therewith pull out sieve.
Clean sieve in water.
Push sieve inwards.
Put on hose.
Tighten covering nut firmly.
Take out detergent suck supports.
Clean filter in water and reinstall.
Ready a catch bin for appr 1 Litre oil.
Loosen release screw.
Tighten release screw.
Fill oil slowly up to the MAX marking.
Note: Air pockets must be able to leak out.
For oil type refer to technical specifications.
DANGER
Risk of injury by inadvertent start-up of appliance and
electric shock. Prior to all work on the appliance, switch
off the appliance and pull the power plug.
Leak in the high pressure system
Check high pressure system and connections for
tightness.
Lack of water after 2 minutes - the pump is
switched off to prevent dry runs.
Check water supply, check connections.
Heater contactor fault
Set the appliance switch to "0/OFF“.
Turn on the appliance.
Error occurs repeatedly.
Inform Customer Service.
Lack of water - heater is switched off
Check water supply, check connections.
No line voltage, see "Appliance is not running".
Heater operation
Engine overload/overheat
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
Error occurs repeatedly.
Inform Customer Service.
Fault in the voltage supply.
Check main connections and mains fuse.
Excessive power consumption.
Check main connections and mains fuse.
Inform Customer Service.
Temperature limiter has got triggered.
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
Error occurs repeatedly.
Inform Customer Service.
System care detection defective
Inform Customer Service.
Temperature sensor defective
Inform Customer Service.
Service interval
Perform service work.
Note: Heater can only operate 5 more hours.
System care bottle empty.
Replace the system care bottle.
Note: Heater operation no longer possible.
System care bottle empty.
Replace the system care bottle.
No power
Check power connection/conduit.
Maintenance Works
Clean the sieve in the water connection
Cleaning the fine filter
Clean the sieve in the safety block
Clean filter at the detergent suck hose
Oil change
Dispose of old oil ecologically or turn in at a gathering
point.
Troubleshooting
Indicator lamp pump
2x blinking
3x blinking
4x blinking
”Low water” indicator lamp
Indicator lamp "Ready for use" turns off
Indicator lamp for heater lights up
Engine indicator lamp
2x blinking
3x blinking
4x blinking
Indicator lamp boiler fault
1x blinking
3x blinking
4x blinking
Indicator lamp service
Indicator lamp system care is illuminated
Indicator lamp system care is blinking
Appliance is not running
20 EN
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher HDS-E 8-16-4M 12kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDS-E 8-16-4M 12kW in the language / languages: All languages as an attachment in your email.

The manual is 4,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info