726290
26
Zoom out
Zoom in
Previous page
1/524
Next page
- 5
Turning the quantity regulation valve in clock-wise direction
will result in higher working pressure and larger volume.
Turning the quantity regulation valve in an anti-clockwise di-
rection will result in lower working pressure and smaller quan-
tities.
DANGER
Risk of injury! When adjusting the pressure/quantity regulation,
make sure that the screw connection of the spray lance does not
become loose.
Turning the water quantity regulator to the right gives more
water flow and higher working pressure.
Turning the water quantity regulator to the left gives lesser
water flow and lower working pressure.
Open the water supply.
Symbol "Engine on"
Release the trigger gun. To do so, push the safety catch to-
wards the back.
Open the trigger gun and set the appliance switch (A) to "1"
(motor on).
The indicator lamp for operational readiness (F) shows that
the appliance is in stand-by mode and ready to be operated.
DANGER
Scalding danger!
ATTENTION
Hot water operations without fuel will cause damage to the fuel
pump. Ensure adequate fuel supply before starting hot water op-
erations.
If required, the burner can also be turned on subsequently.
Symbol "Burner on"
Turn the appliance switch (A) to "Burner on".
Set the desired water temperature on the thermostat (B).
Maximum temperature is 98 °C.
DANGER
Scalding danger! The operating pressure must not exceed 3,2
MPa (32 bar) when operating with temperatures above 98 °C.
For shifting from hot water to steam operations, first cool down the
machine and switch it off. Then do the change-over as follows:
Replace the high pressure nozzle with the steam nozzle
(accessory).
Set the thermostat to 150 °C.
Set the water flow regulation valve of the high pressure pump
to minimum water flow (turn in the anti-clockwise direction).
Set the water flow regulation valve of the high pressure pump
to maximum water flow (turn in the clockwise direction).
Set the water flow regulator at the trigger gun to minimum wa-
ter flow by turning it towards the left.
If the trigger gun is closed during operation, the appliance will
switch off.
The appliance will automatically start again when you open
the gun again within the stand-by period (2 ... 8 minutes).
If the stand-by period is exceeded, the safety time mecha-
nism switches off the pump and the burner. The indicator
lamp Operations Stand-by (F) goes off.
To restart the appliance, set the appliance switch to "0" and
then switch on the appliance again. If the appliance is operat-
ed using remote control, the appliance can be restarted by us-
ing the corresponding switch of the remote control device.
Vehicle tyres are only cleaned using the flat spray nozzle
((25°) from a minimum spraying distance of 30 cm. The round
spray should never be used to clean tyres.
The following nozzles can be selected for all other tasks:
Set working pressure and flow rate
Appliance setting
Adjusting the pressure/quantity regulation of the trigger gun
(option)
Operating with cold water
R
Operating with hot water
Operating with steam
Order No. Type
4.116-000 HDS 9/14
4.116-001 HDS 12/14
Without pressure/quantity regulation at the trigger gun
With pressure/quantity regulation at the trigger gun (option)
Operations stand-by
Selecting the nozzle
Dirt Nozzle Spray an-
gle
Part no.: Pressure
[MPa]
Recoil [N]
HDS 9/14
strong 00060 5.765-240 14 44
medium 25060 25° 5.765-027
light 40060 40° 5.130-087
HDS 12/14
strong 00080 5.765-243 14 55
medium 25080 25° 5.765-061
light 40080 40° 5.765-221
26 EN
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher HDS 12-14-4 ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDS 12-14-4 ST in the language / languages: All languages as an attachment in your email.

The manual is 17,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info