726294
26
Zoom out
Zoom in
Previous page
1/376
Next page
- 10
Fault Possible cause Remedy of whom
Appliance is not running There is no voltage in the machine. Check electrical mains. Electrician
Motor protection switch for the con-
trol has been triggered.
Check motor protection switch. Customer Service
Pump starts during the stand-by
period and not when the hand
spray gun is opened.
Pressure sensor for high pressure
or cable to pressure sensor defec-
tive.
Replace pressure sensor or cable. Customer Service
Full pressure does not build up
in the appliance
Flushed the nozzle. Replace the nozzle. Operator
Suction site pipe leaking. Check screw fittings and hoses. Operator
Safety valve is leaky. Check the setting; install new washers, if re-
quired.
Customer Service
Overflow valve is leaking or set too
low.
Check valve parts; replace damaged parts;
clean the dirt.
Customer Service
Valve in the pump defective, high-
pressure solenoid valve does not
close.
Replace defective components. Customer Service
High pressure pump is knock-
ing; manometer is swaying wild-
ly
Pump is sucking air. Check suction system and remove leaks. Operator
Valve plate or valve spring is defec-
tive.
Replace defective components. Customer Service
Advance pump calcified or defec-
tive.
Check advance pump. Operator
Overflow valve opens and clos-
es continuously during 0 takeo-
ver
Leakage in the high-pressure pipe-
line system or hand spray gun leak-
ing.
Locate and seal leakage. Operator
Backflow valve or control piston
seal leaking in overflow valve.
Repair the overflow valve. Customer Service
Error code 01 is displayed Control board defective, green
LEDs are not blinking.
Check control board, replace if necessary. Customer Service
Error number 10, 11, 12, 13 is
displayed
Overflow protection switch of the
respective high pressure pump has
been triggered.
Rectify cause for over-loading. Customer Service
Error code 14 is displayed Motor protection switch has been
triggered or frequency inverter not
ready.
Rectify cause for over-loading. Customer Service
Error number 18, 19, 20, 21 is
displayed
Thermal sensor of the respective
motor has been triggered.
Rectify cause for over-loading. Customer Service
Error code 26 is displayed Overflow protection switch of the
advance pressure pump has been
triggered.
Rectify cause for over-loading. Customer Service
Error code 40 is displayed The water shortage safeguard in
the swimmer tank has got activat-
ed.
Remove the water shortage. Operator
Swimmer valve is jammed. Check swimmer valve for free movement. Operator
Error code 41 is displayed The temperature sensor in the
swimmer tank has been activated.
Reduce water infeed temperature. Operator
Error code 42 is displayed Leakage in the high-pressure pipe-
line system.
Locate and seal leakage. Operator
Too many consumer loads open at
the same time.
Close some consumer loads. Operator
Pressure sensor for high pressure
defective.
Replace pressure sensor. Customer Service
Error code 43 is displayed Leakage in the high-pressure pipe-
line system.
Locate and seal leakage. Operator
Pressure sensor for high pressure
defective.
Replace pressure sensor. Customer Service
Error code 45 is displayed Pressure too high (> 300 bar). Incorrect nozzle inserted. Insert correct noz-
zle.
Operator
Pressure sensor for high pressure
defective.
Replace pressure sensor or cable. Customer Service
Error code 46 is displayed Flowmeter issues signal > 50 l/min
flow, although no pump is running.
Check flowmeter, replace if required. Customer Service
26 EN
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher HDC 90-10 H Advanced at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDC 90-10 H Advanced in the language / languages: All languages as an attachment in your email.

The manual is 32,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info