726310
25
Zoom out
Zoom in
Previous page
1/396
Next page
- 9
CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
DANGER
Risk of injury! The main switch is to be
switched off while carrying out any repairs
or maintenance jobs.
Transport Storage Care and maintenance
Maintenance schedule
Time Activity Assembly affected Performance of whom
daily Check hand-
spray gun
Hand spray gun Check whether the hand-spray gun closes tightly
without any leaks. Check the protection mecha-
nism against accidental switching. Replace de-
fective hand-spray guns.
Operator
Check high pres-
sure hoses
Outlets, hoses towards working
machine
Check hoses to see if there are damages. Re-
place defect hoses immediately. Danger of acci-
dent!
Operator
weekly or after 40
operating hours
Check the unit for
leaks
Entire plant Check pumps, overflow valve and pipe system for
leaks. Inform Customer Service if there is oil be-
low the pump or if there is a leakage of more than
3 drops of water per minute. Keep the leakage
borings clear.
Operator/
Customer
service
Check oil level Oil level indicator on the pump If the oil is milky, it needs to be replaced. Operator
Check oil level Oil level indicator on the pump Check oil level of the pump. Refill oil if required
(Order no. 6.288-016)
Operator
monthly or after 200
operating hours
Check pump High-pressure pump Check the pump for leaks. If the leakage is more
than 3 drops per minute, call Customer Service.
Operator
Check water
scarcity fuse
Swimmer switch in the swimmer
tank
Press the swimmer of the low water fuse down for
about 5 seconds and control the error indicator on
the control board. Remove deposits if necessary.
Operator
Test swimmer
valve
Float tank The water level must be 40 mm above the over-
flow. No water must exit while the swimmer valve
is closed.
Operator
Check over-
pump time.
Controls Close consumer loads (e.g. hand spray guns).
The pump must switch off after the afterrun peri-
od.
Operator
Test automatic
start
Pressure sensor The pump stands still as there is no water trans-
fer. Open the hand spray gun. If the pressure in
the high-pressure cycle falls below the switch-
point, the pump must switch on.
Operator
Tighten hose
clips
All hose clips Tighten the hose clips using a torque wrench.
Tightening torque up to a diameter of 28 mm =
2Nm, from 29 mm = 6 Nm.
Operator
half-yearly or after
500 operating hours
Oil change High-pressure pump Drain off oil. Fill in 1 l of fresh oil (order no. 6.288-
016.0). Check the oil level at the oil level indica-
tor.
Operator
half-yearly or after
1000 operating
hours
Check the appli-
ance for calcium
deposits
entire water system Improper functioning of valves or pumps can be
an indication of calcium deposits. If necessary
decalcify.
Operator
trained in de-
calcification
Tighten clamps Control board Tighten all clamps for components in the main cir-
cuit.
Electrician
Test swimmer
valve
Float tank The water level must be 40 mm above the over-
flow. No water must exit while the swimmer valve
is closed.
Customer
Service
annual Safety check Entire plant Safety check according to the guidelines for fluid
spraying equipment.
Technical ex-
pert
25EN
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher HDC 80-8H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDC 80-8H in the language / languages: All languages as an attachment in your email.

The manual is 50,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info