Manual Karcher HDC 60-8 (page 19 of 396) (All languages)

726305

Zoom out

Zoom in

1/396

- 3

The water flows back from the swimmer

tank to the suction side of the pump. The

water level in the swimmer tank is kept con-

stant by the swimmer valve. In case of fail-

ure of the swimmer valve, the water exits

via the overflow. If the water supply is dis-

turbed, the lack of water fuse will send an

error message to the controls.

The electric engine will drive the crankshaft

pump. The pump transports the water un-

der high pressure to the pressure side.

The high-pressure water reaches the high-

pressure output via the overflow valve and

the pressure sensor. After that, there will be

the high-pressure network of the operator.

Remaining water will be routed back to the

floater basin by the overflow valve. If all

consumer loads have been switched off,

the overflow valve will completely switch to

backflow to the floater basin. If the pressure

at the output exceeds the maximum operat-

ing pressure at the output, the safety valves

will open.

– The appliance will be switched to

READY mode by activating the release

switch. If the pressure in the systems

sinks below the determined switch-on

point due to the opening of a hand

spray gun, the high-pressure pumps will

be switched on.

– If the flow switch at the overflow valve is

triggered while the high-pressure

pumps are running after closing all

hand sprayguns, the pump is switched

off once again with a 30 second delay.

– If the system is ready and the high-

pressure pumps are not turned on, a

timer is started, which will reset the

readiness of the unit after 6 hours.

Safety devices serve for the protection of

the user and must not be put out of opera-

tion or bypassed with respect to their func-

tion.

The safety mechanism against lack of wa-

ter prevents the high pressure pumps from

being switched on when there is no water.

The temperature sensor switches off the

appliance as soon as the water tempera-

ture is too high.

The winding protection contact in the motor

winding of the pump drive switches off the

engine when there is a thermal overload.

– The safety valve opens when the over-

flow valve is defective.

– The safety valve is set by the manufac-

turer and sealed. Setting only by cus-

tomer service.

– If all hand spray guns are closed, the

overflow valve opens and the entire wa-

ter volume will flow back into the floater

basin. The high pressure pumps are

switched off via the flow switch once the

set delay time has elapsed.

– The remaining water flows back into the

floater basin via the overflow valve.

If the hand spray gun is opened again, the

high pressure pumps will restart via the

pressure sensor for high pressure.

Water inlet

Pumps

High pressure side

Pressure regulation

Controls

Safety Devices

Safety mechanism against lack of

water in swimmer tank

Temperature sensor

Winding protection contact

Safety valve

Overflow valve with flow switch

Pressure sensor for high pressure

19EN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDC 60-8 in the language / languages: All languages as an attachment in your email.

The manual is 50,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher HDC 60-8 Manual

Product: