726303
19
Zoom out
Zoom in
Previous page
1/396
Next page
- 3
The water flows back from the swimmer
tank to the suction side of the pump. The
water level in the swimmer tank is kept con-
stant by the swimmer valve. In case of fail-
ure of the swimmer valve, the water exits
via the overflow. If the water supply is dis-
turbed, the lack of water fuse will send an
error message to the controls.
The electric engine will drive the crankshaft
pump. The pump transports the water un-
der high pressure to the pressure side.
The high-pressure water reaches the high-
pressure output via the overflow valve and
the pressure sensor. After that, there will be
the high-pressure network of the operator.
Remaining water will be routed back to the
floater basin by the overflow valve. If all
consumer loads have been switched off,
the overflow valve will completely switch to
backflow to the floater basin. If the pressure
at the output exceeds the maximum operat-
ing pressure at the output, the safety valves
will open.
The appliance will be switched to
READY mode by activating the release
switch. If the pressure in the systems
sinks below the determined switch-on
point due to the opening of a hand
spray gun, the high-pressure pumps will
be switched on.
If the flow switch at the overflow valve is
triggered while the high-pressure
pumps are running after closing all
hand sprayguns, the pump is switched
off once again with a 30 second delay.
If the system is ready and the high-
pressure pumps are not turned on, a
timer is started, which will reset the
readiness of the unit after 6 hours.
Safety devices serve for the protection of
the user and must not be put out of opera-
tion or bypassed with respect to their func-
tion.
The safety mechanism against lack of wa-
ter prevents the high pressure pumps from
being switched on when there is no water.
The temperature sensor switches off the
appliance as soon as the water tempera-
ture is too high.
The winding protection contact in the motor
winding of the pump drive switches off the
engine when there is a thermal overload.
The safety valve opens when the over-
flow valve is defective.
The safety valve is set by the manufac-
turer and sealed. Setting only by cus-
tomer service.
If all hand spray guns are closed, the
overflow valve opens and the entire wa-
ter volume will flow back into the floater
basin. The high pressure pumps are
switched off via the flow switch once the
set delay time has elapsed.
The remaining water flows back into the
floater basin via the overflow valve.
If the hand spray gun is opened again, the
high pressure pumps will restart via the
pressure sensor for high pressure.
Water inlet
Pumps
High pressure side
Pressure regulation
Controls
Safety Devices
Safety mechanism against lack of
water in swimmer tank
Temperature sensor
Winding protection contact
Safety valve
Overflow valve with flow switch
Pressure sensor for high pressure
19EN
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher HDC 40-16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDC 40-16 in the language / languages: All languages as an attachment in your email.

The manual is 50,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info