Manual Karcher HD 8-18-4 MX (page 14 of 204) (All languages)

725221

Zoom out

Zoom in

1/204

14 English

Colour coding

 Control elements for the cleaning process are yel-

low.

 Control elements for maintenance and servicing are

light grey.

Unpacking

1. Check the package content when unpacking.

2. Notify the dealer immediately in the case of shipping

damage.

3. Only with HD...M St: Store the drilling template on

the packaging for mounting the device on the wall.

Installing accessories

Note

No accessories are supplied in the scope of delivery for

the HD...M St.

Note

The EASY!Lock system connects components quickly

and safely via a single turn of the quick-release thread.

Figure A

1. Plug the high-pressure nozzle onto the spray lance.

2. Fit the union nut and hand-tighten (EASY!Lock).

3. Connect the spray lance to the high-pressure gun

and hand-tighten (EASY!Lock).

For devices without a hose reel:

1. Connect the high-pressure hose to the high-pres-

sure gun and high-pressure connection of the de-

vice and tighten hand-tight (EASY!Lock).

For devices with a hose reel:

1. Lay the high-pressure hose on the ground in a

straight line.

2. Turn the crank clockwise and wind the high-pres-

sure hose onto the hose reel in evenly distributed

layers. Take care to ensure that the hose does not

become kinked.

3. Connect the high-pressure hose to the high-pres-

sure gun and hand-tighten (EASY!Lock).

Initial startup

Installation of HD...M St

 DANGER

Danger of injury from electric shock

Only allow authorised technical specialists to install the

water supply, electrical connections and high-pressure

network.

Ambient conditions

 Dry, frost-free environment.

 No danger of explosion.

 Solid, level floor or wall of sufficient loading capacity.

 Do not install in the vicinity of residential spaces or

offices (noise emission).

 Accessibility for maintenance work.

 Water drain at installation location.

Fastening the device

Note

Screws and dowels for fastening the holder are not pro-

vided in the scope of delivery. The must be selected to

suit the requirements of the installation location and

must be procured separately. Required screw diameter

of 6...8 mm.

 DANGER

Risk of injury from a falling device

Take the weight of the device and the loading capacity

of the installation location into account when selecting

the fasteners.

Figure B

1 Wall mounting

2 Floor installation

3 Mounting opening

4 Holder

1. Mark the mounting holes on the wall or floor using

the drilling template.

2. Drill the holes.

3. Attach the holder but only tighten the screws lightly.

4. Adjust the holder clearance by turning with an open-

end wrench.

5. Tighten the fastening screws.

6. Mount the device.

Electrical connection

 DANGER

Risk of injury from electric shock

Use a plug to connect the device to the mains grid. Per-

manent connection to the mains grid is prohibited. The

plug is used for disconnection from the mains.

HD...M St: The power supply used for operating the de-

vice must be able to supply enough power for continu-

ous operation.

HD...M St: All live parts, cables and devices in the work

area must be protected against water jets.

1. Plug the mains plug into the socket.

Water connection

Connection to a water line

몇 WARNING

Health risk from return flow of contaminated water

into the drinking water network.

Observe the regulations of your water supply company.

According to applicable regulations, the device must

never be used with the drinking water network without a

system separator. Use a system separator from

KÄRCHER or a system separator as per EN 12729

Type BA. Water that has flowed through a system sep-

arator is classified as undrinkable. Always connect the

system separator to the water supply and never directly

to the water connection on the device.

1. Check the feed pressure, input temperature and in-

put amount of the water supply. See the "Technical

data" section for the requirements.

2. Connect the system separator and water connection

of the device with a hose (minimum length 7.5 m,

minimum diameter 1”).

The supply hose is not included in the scope of de-

livery.

3. Open the water inlet.

Suck water from the container

1. Screw the suction hose (order number 4.440-207.0)

and filter (order number 4.730-012.0) onto the water

connection.

2. Vent the device.

Vent the device

1. Unscrew the nozzle from the spray lance.

2. Allow the device to run until the escaping water is

free of air bubbles.

3. In the case of venting problems, allow the device to

run for 10 seconds and then switch it off. Repeat the

procedure several times.

4. Switch off the device.

5. Screw the nozzle back in place.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HD 8-18-4 MX in the language / languages: All languages as an attachment in your email.

The manual is 8,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher HD 8-18-4 MX Manual

Product: