804567
9
Zoom out
Zoom in
Previous page
1/112
Next page
- 3
Rugs with jute backing can shrink if too
much water is used and can bleed col-
ours.
Brush high-fiber rugs in the direction of
the weave after cleaning (using a fiber
brush or a scrubber).
Do not step on cleaned surfaces until
they have dried and do not place furni-
ture on them to avoid pressure spots or
rust stains.
When cleaning previously shampooed
carpets, foam will be generated in the
dirt water reservoir. In such a case add
Foam ex RM 761 to the dirt water reser-
voir.
Set the appliance switch to "OFF".
Empty the dirt water reservoir.
Pull the drain hose for the fresh water
off the hose nipple an drain the deter-
gent solution.
Fill the fresh water tank with approx. 4
liters of hot water (max. 60°C) and flush
the spray system by pressing the deter-
gent solution key.
Disconnect the main plug from the
socket.
Pull the drain hose for the fresh water
off the hose nipple an drain the deter-
gent solution.
Clean the sieves below the fresh water
tank and inside the dome.
Rinse the waste water tank with clear
water.
Tilt the appliance backwards and clean
the cleaning head and the vacuum bar..
In case of danger of frost:
Empty the fresh and waste water tank.
Store the appliance in a frost-protected
room.
WARNING
Danger of injury by electric shock.
Pull out the mains plug before doing any
maintenance or cleaning jobs.
daily
Check high power cable, extension ca-
bles and hoses for damage every time
before use.
Check brush rollers for cleanliness;
clean if required.
Check the brushes for wear, replace if re-
quired.
The brushes are considered worn, if the
bristles have the same length as the yel-
low indicator bristles.
Check the dome and seals for damages.
Check the vacuum bar for contamina-
tion, clean if required
Check spray pattern of the nozzle.
WARNING
Risk of damage. Never use a wire or a nee-
dle to clear plugged nozzles, but rinse them
with hot water (see "Troubleshooting").
Weekly
Check hoses and seals to see if there
are damages. Have defective parts re-
placed by Customer Service.
Check the pump pressure of the water
pumps.
Check the vacuum bar for damages.
Quarterly
Check the carbon brushes in suction
turbine. Have defective parts replaced
by Customer Service.
Check the V-belt. Have defective parts
replaced by Customer Service.
Check the cable for friction spots. Have
defective parts replaced by Customer
Service.
Empty the fresh water tank and waste
water tank.
Tilt the appliance backwards and store
it on the fresh water reservoir.
Rotate the nozzle by 90° counter-clock-
wise and remove them from the nozzle
seat.
Install the new nozzle in reverse order.
Empty the fresh water tank and waste
water tank.
Tilt the appliance backwards and store
it on the fresh water reservoir.
Push the clip of the brush roller holder
toward the outside.
Remove the brush roller from the bot-
tom of the cleaning head.
Slide the new brush roller onto the roller
mandrel in the cleaning head and press
it upward into the clip until it audibly
locks into place.
NOTICE
When installing the brush rollers watch for
correct placement. The black brush roller
sits on the inside of the cleaning head, the
white one is located on the outside.
DANGER
Danger of injury by electric shock.
Pull the plug from the mains before carrying
out any tasks on the appliance.
Get the electrical components checked and
repaired only by authorised customer ser-
vice persons.
Contact an authorised customer service
person in case of problems not mentioned
in this chapter or if you are in doubt or when
you have been explicitly asked to do so.
Plug in the mains plug.
Check facility fuse.
Reset the suction turbine fuse on the
control panel.
Clean the vacuum bar.
Check, clean or replace the seal on the
dome.
Empty the waste water tank.
Insert the suction hose properly on the
dome.
Check the suction hose for damages.
Set the appliance switch to normal op-
eration.
Fill the fresh water tank with hot water
(max. 60°C) and rinse the nozzle. Re-
place the nozzle as applicable (see
"Maintenance task/replace nozzle").
Fill up fresh water reservoir.
Clean the sieve below the fresh water
tank.
Set the appliance switch to normal op-
eration.
Reset the brush drive fuse on the con-
trol panel.
Check the drive belt, replace if required.
Replace the worn nozzle with a new
one (see "Maintenance task/replace
nozzle").
Danger
Risk of injury and electrical shock! Repair
works may only be performed by the au-
thorised customer service.
Only use accessories and spare parts
which have been approved by the man-
ufacturer. The exclusive use of original
accessories and original spare parts
ensures that the appliance can be oper-
ated safely and trouble free.
For additional information about spare
parts, please go to the Service section
at www.kaercher.com.
Shutting down
Cleaning the device
Frost protection
Care and maintenance
Maintenance intervals
Maintenance Works
Replace the nozzle
Replacing the brush roller
Troubleshooting
Appliance is not working
Suction turbine does not run
Insufficient vacuum performance
No water exiting from nozzle
Brush does not turn
Carpet gets too wet
Accessories and Spare Parts
Accessories Part no.:
Brush, standard 8.621-605.0
Brush, natural, soft 8.629-525.0
Hand nozzle 4.130-163.0
Spray/suction hose 4.440-644.0
9EN
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher BRC 45-45 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher BRC 45-45 C in the language / languages: All languages as an attachment in your email.

The manual is 20.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info