804745

Karcher BR 30-1 C Bp Manual

16
Zoom out
Zoom in
Previous page
1/224
Next page
16 English
●The floor is cleaned by moving the device back and
forth at a speed similar to vacuum cleaning.
●Activate the Boost function for heavy soiling. To do
this, hold down the Boost function button. The roller
speed and fresh water quantity are increased when
the Boost function is activated. Allow the device to
slide slowly over the floor without exerting any pres-
sure on the device.
Illustration I
●If the cleaning rollers are blocked, e.g. by jamming,
the device switches off.
The warning light lights up.
Remove the blockage.
To switch the device on again, press the ON/OFF
switch twice.
Note
The first press clears the error, the second press switch-
es on the device.
If the ON/OFF switch is not pressed, the warning light
goes out after 10 s. To switch on the device, press the
ON/OFF switch once.
Illustration J
●If the capacity of the battery pack is almost exhaust-
ed, the ON/OFF switch starts to flash.
Illustration K
Press the ON/OFF switch.
The device switches off.
Take the battery pack out of the device and charge
it (see chapter Ending operation).
Note
In order to avoid a damaging exhaustive discharge of
the battery pack, the device switches itself off before the
battery pack is completely discharged.
●Switch off the device and move it to the parking po-
sition whenever work is interrupted and at the end of
work. When the device is in the parking position, the
cleaning rollers do not touch the floor.
Illustration L
●When parking the device, do not lean it against
walls, doors or other objects; instead, bring the de-
vice into the parking position.
Illustration M
Starting work
ATTENTION
Uncontrolled motion
Damage to the device and material damage
The cleaning rollers start rotating as soon as the device
is switched on.
Hold the handle tight to prevent the device from moving
away independently.
ATTENTION
Fresh water tank or waste water tank not installed
Material damage
Before starting cleaning work, ensure that the fresh wa-
ter tank is filled with water and the waste water tank is
fitted in the device.
1. Remove the cleaning rollers from the device (see
chapter Cleaning the cleaning roller).
2. Moisten the cleaning rollers with fresh water.
3. Install the cleaning rollers.
4. Press the ON/OFF switch.
Illustration N
The device switches on.
5. Activate the boost function to clean stubborn dirt
(see chapter General notes on operation).
Emptying the waste water tank
●Empty the waste water tank as soon as the fresh
water tank is empty, or the device no longer absorbs
moisture, and water remains on the floor.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Disengage the two locking flaps on the device.
Illustration O
The waste water tank releases from the device.
4. Lift the device and set it aside.
5. To transport it to the emptying point, do not hold the
waste water tank by the lid, but with both hands on
the side of the drip tray. Keep the waste water tank
level, otherwise waste water can escape.
6. Empty the waste water tank.
Illustration P
In the case of stubborn dirt, rinse out the waste wa-
ter tank with tap water (see chapter Cleaning the
waste water tank).
7. Clean the sweep bins (see chapter Cleaning the
sweep bins).
8. Insert the waste water tank into the device in reverse
order.
Interrupting operation
ATTENTION
Risk of damage due to moisture and detergents as
well as the device tipping over
Risk of material damage on sensitive floors and on the
cleaning rollers due to prolonged exposure to moisture
and detergents.
Risk of material damage if the device falls over.
Always move the device to the parking position when
you take a break from work and after work.
Do not lean the device against walls, doors or other ob-
jects when setting it down.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
Rinsing the cleaning rollers
The rinsing function can be used for intermediate clean-
ing of the cleaning rollers in case of severe dirt accumu-
lation.
Note
At the end of work and before storing the device, the
cleaning rollers must be removed and cleaned under
running water or in the washing machine (see chapter
Cleaning the cleaning roller). The rinsing function does
not replace final basic cleaning.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Check the filling level in the fresh water tank, it must
be at least 50%.
If necessary, fill the fresh water tank accordingly
(see chapter Filling the fresh water tank).
4. Press and hold the Boost function button.
Illustration Q
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher BR 30-1 C Bp at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher BR 30-1 C Bp in the language / languages: All languages as an attachment in your email.

The manual is 5.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info