804750
15
Zoom out
Zoom in
Previous page
1/252
Next page
English 15
BD 70/75 80 Ah:
1Battery
2Battery pole
3Circular connector
4Spacer 150x150x65
5Additional weight, 6 plates
6Additional weight, 14 plates
BD 70/75 160 Ah:
1Battery
2Battery pole
3Circular connector
4Spacer 150x150x65
5Spacer 155x300x60
5. Insert the spacers and additional
weights as indicated.
ATTENTION
Risk of damage
If the polarity (plus and minus terminal) is
reversed, the control electronics will be
damaged.
Connect the red cable to the plus terminal
and the black cable to the minus terminal.
Observe the illustrations shown above
when connecting the cables.
6. Clamp the connecting cables onto the
(+) and (-) battery terminals.
7. For the devices with two batteries, at-
tach the connecting cable between the
two batteries.
8. Plug the circular connectors into the bat-
teries.
9. Connect the device-side battery connec-
tor to the battery-side battery connector.
10.Pivot the waste water tank downwards.
Note
Charge the batteries before starting up the
device (see section "Charging the batter-
ies").
Removing the batteries
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned sta-
bly when removing and installing the batter-
ies.
1. Turn the key-operated switch to "0" and
remove the key.
2. Disconnect the battery plug.
3. Drain the waste water.
4. Pivot the waste water tank upwards.
5. Unplug all circular connections.
6. Disconnect the device-end cable from
the negative terminal of the battery.
7. Disconnect the remaining cables from
the batteries.
8. If necessary, remove the spacers.
9. Remove the batteries.
10.Dispose of the used batteries in accord-
ance with statutory provisions.
Initial startup
Charging the battery
DANGER
Inappropriate use of the charger
Electric shock
Adhere to the mains voltage and fuse val-
ues specified on the device type plate.
Only use the charger in dry rooms with suf-
ficient ventilation.
ATTENTION
Using an unsuitable charger
Risk of damage
Do not connect the charger to the device-
side battery connector.
Use only a charger suitable for the type of
battery installed.
Read the operating instructions of the
charger manufacturer and observe the
safety instructions in particular.
The device cannot be used during the
charging process.
Note
The device has deep discharge protection,
i.e. the brush motor and turbine are
switched off automatically when the permit-
ted minimum capacity level is reached.
1. Drive the device directly to the charger
and do not drive on slopes.
2. Pull out the device-side battery connec-
tor.
1Battery plug, device side
2Battery plug, battery side
ATTENTION
Risk of damage
Do not connect the charger to the device-
side battery connector.
Note
Please read the operating instructions of
the charger manufacturer, especially the
chapters on safety instructions!
3. Connect the battery-side battery con-
nector to the charger.
4. Plug the mains plug of the charger into
the socket.
5. Carry out the charging process in ac-
cordance with the operating instructions
for the charger.
The charging time depends on the bat-
tery condition and the charger. When the
battery is empty, the charging time is ap-
proximately:
6. After the charging process is complete:
a Unplug the mains plug of the charger.
b Disconnect the battery connector from
the charger.
c Connect the device-side battery con-
nector to the battery-side battery con-
nector.
Operation
ATTENTION
Risks during operation
Danger of injury
Release the safety switch in the case of
danger.
Filling with operating materials
Filling fresh water
1. Open the fresh water tank cap.
2. Fill fresh water (max. 50 °C) to the lower
edge of the filling nozzle.
Note: The fresh water hose can be
clamped with the hose holder during fill-
ing.
3. Close the fresh water tank lock.
Notes on detergents
WARNING
Risk of damage to the device!
If unsuitable detergents are used, the de-
vice may get damaged.
Use only recommended detergents. The
operator carries all increased risks relating
to operational safety and increased risk of
accidents if using other detergents.
Use only detergents free of solvents, salt
and hydrofluoric acid.
Adhere to the safety instructions stated on
the detergent packaging.
Note
Do not use heavily foaming detergent.
Recommended detergents
1
1
2
Charger Battery ca-
pacity
Charging
time approx.
6.654-483.0 80 Ah 7 hours
6.654-484.0 80 Ah 2 hours
160 Ah 4 hours
Application Detergent
Floor maintenance cleaner
extra low foaming with EU
Ecolabel
APPROX. 50
C
Highly wetting universal
cleaner
RM 756
Intensive alcohol cleaner for
floors and surfaces. Well-
suited for hard rock such as
granite
RM 755
Fine stone cleaner, sur-
factant-free
RM 753
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher BD 70-75 W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher BD 70-75 W in the language / languages: All languages as an attachment in your email.

The manual is 141.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info