804739
13
Zoom out
Zoom in
Previous page
1/192
Next page
- 5
Remove the vacuum bar.
Unscrew the star grips.
Remove the plastic parts.
Remove the vacuum lips.
Insert new or reversed vacuum lips.
Insert the plastic parts.
Screw in and tighten the star grips.
Push down the device holding the push
handle so that the cleaning head is
raised.
Press the pedal for changing the brush-
es downward beyond its resistance.
Pull the device towards the back so that
the disc brush becomes accessible.
Place a new disc brush on the floor in
front of the device.
Drive the device with the raised clean-
ing head over the new disc brush and
lower the cleaning head.
The brush locks into the drive.
Drain off dirt water.
Lift up the waste water tank and put it
aside.
To ensure a reliable operation of the appli-
ance maintenance contracts can be con-
cluded with the competent Kärcher sales
office.
In case of danger of frost:
Empty the fresh and waste water tank.
Store the appliance in a frost-protected
room.
DANGER
Risk of injury! Set the programme selector
switch to "OFF" and disconnect the mains
plug prior to performing any work on the de-
vice.
Drain and dispose of the dirt water and
the residual fresh water.
Replacing the disk brushes Removing the waste water tank
Maintenance contract
Frost protection
Faults
Failure Correction
Appliance cannot be
started
Turn the program selection switch to the desired programme.
Operate the safety switch.
Insert the mains plug into the socket.
Is the indicator light voltage supply on?
Insufficient water quan-
tity
Check fresh water level, refill tank if necessary.
Increase the water volume on the regulating knob for water volume.
Clean sieve.
Insufficient vacuum per-
formance
Clean the seals between waste water tank and cover and check for tightness, replace if required.
Check the seals between waste water tank and fresh water tank for damage, replace if necessary.
Wastewater reservoir is full; shut off the appliance and empty the wastewater reservoir
Clean the fluff filter.
Clean the vacuum lips on the vacuum bar, replace if required
Check if the cover on the dirt water discharge hose is closed
Check the setting of the vacuum bar.
Check suction hose for blockages; clean if required.
Check the suction hose for tightness; replace if required.
Insufficient cleaning re-
sult
Check the brushes for wear, replace if required.
Suction turbine is run-
ning rough
Clean the swimmer.
Brush does not turn Check if foreign objects block the brush; remove foreign object if required.
Release the safety switch.
Wait for a while.
Operate the safety switch.
Vibrations during clean-
ing
You might need to use a softer brush.
In case of faults that cannot be remedied using the table below please contact the customer service.
13EN
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Karcher BD 43-35 C Ep at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Karcher BD 43-35 C Ep in the language / languages: All languages as an attachment in your email.

The manual is 17.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info