713565

Kalorik TKG HC 1002 R Manual

10
Zoom out
Zoom in
Previous page
1/56
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
10
TKG HC 1002 R - 130306
Assembly page 10/56
Fax +32 2 359 95 50
Attachment comb #I…...leaves hair approx. 1/8" in length
Attachment comb #II…..leaves hair approx. 1/4" in length
Attachment comb #III....leaves hair approx. 3/8" in length
Attachment comb #IIII...leaves hair approx. 1/2" in length
• In order to become accustomed to the length of each attachment comb we
recommend for the first use to place the attachment comb #IIII and then to reduce the
length steadily until you obtain the desired length. Afterwards, you can place directly the
comb you want.
• For uniform cutting, never push or force the clipper through the hair at a fast pace. The
clipper works most efficiently when it works at its own speed.
• Start by combing the hair in its natural direction.
• Once you placed the attachment comb on the hair clipper, cut the hair by placing the
comb teeth flat against the scalp. We recommend proceeding by small lengths in order
to avoid stuffing. Therefore you only have to remove the comb regularly by bending it
lightly outward. Then make the same movement but start lower than the point at which
you removed the clipper in order to obtain a homogeneous length.
• The cutting always happens by moving towards in the opposite side of the natural
direction of the hair. For the backside, start from the nape of the neck and go to the top
of the head, for the sides, from the ears to the top of the head and for the top of the
head, from the forehead to the backside of the head.
• We recommend doing the hair regularly in order to check the homogeneity of the cutting
and to replace the hair. For the same reason, once the hair is cut and done, work the hair
clipper again but quicker in order to cut the hair that would have escaped from the first
cutting. You can eventually insist on the places with defaults.
Short cuts
• Always cut from the back of the neck to the crown, using the longest attachment comb
(IIII). Holding it flat against the head, slowly move the clipper up through the hair. Use the
same technique for the sides, cutting from the bottom to the upper side of the head (9).
• For the front of the crown, cut the hair against the direction in which it grows. Then even it
up with the sides (10).
• To taper hair down to the neckline, use closer cutting attachment combs. Comb hair,
check for uneven spots and outline sideburns and neckline (11).
CUTTING WITHOUT COMB ATTACHMENT
To cut the hair with the help of a comb or your fingers as well as to cut the outlines, you do not
need a comb attachment.
Put the switch in position “0” and remove the attachment comb by sliding it forward.
Cutting hair with the help of a comb or your fingers
Remove the comb attachment carefully, as explained in the previous paragraph.
Raise a wisp of hair with the help of the comb (12), or take the wisp between your fingers (13).
Take the wisp through the comb or fingers until only the desired hair length remains under the
comb/fingers. Cut the hair that is above the comb or fingers with the hair clipper (14 and 15).
Outlining
• Outlining requires no attachment combs.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalorik TKG HC 1002 R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalorik TKG HC 1002 R in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info