725632
60
Zoom out
Zoom in
Previous page
1/64
Next page
EN-60 Original User Guide | Pedelec Integrale 0.5 Version 2
Description Cause Remedy
Recuperation is not working. a) The battery charge level is
higher than 90%.
a) Recuperation only works for a battery charge level ≤ 90%.
b) The current speed of travel is
lower than 10 km/h
b) Recuperation does not take place at speeds below 10 km/h.
c) The current speed of travel is
higher than 40 km/h
c) Recuperation performance decreases at speeds above 40 km/h.
d) The ambient temperature is
lower than 0°C
d) The battery will not charge when its cell temperature is below 0°C, and recuperation is therefore also not
possible.
e) The bicycle lighting is
switched on
e) The lighting must be switched o in order to activate recuperation.
The motor does not provide full power a) The motor may be subject to
high temperature ranges.
a) From an electronic temperature of 80°C upwards, the performance will gradually reduce. Allow the Pedelec
to cool for approx. 10 minutes (in the shade) before resuming your journey.
b) Battery at. b) As the battery voltage decreases (from a charge level of <25%), the performance as well as the top speed
also reduce slightly. With an almost empty battery, the maximum speed can be 2-3 km/h below the level
when riding with a fully charged battery.
I have noticed a slight bearing play on the
rear wheel.
The drive is tted with a oating
bearing.
In contrast to the normal bicycle wheel hubs and hub dynamos, a hub motor generates heat. This heat causes
the internal components to expand. In order to prevent the dierent expansion behaviour of the installed
materials from leading to an increased component stress when heat is generated, the drive is equipped with
a oating bearing. In practice this means that: When the unit is cold, you may notice a slight bearing play.
A 2-mm play measured on the brake ank of a 28" wheel is within tolerances and no cause for concern. This
bearing play will dissipate once the motor is warm.
The Pedelec does not provide any assistance
after it is switched on, what can I do?
Pedal was used too soon When you switch on assistance during a ride, the pedals must be released for approx. 3 seconds so that the
motor assist mode can switch on.
A blue screen will appear briey during
the start-up processfollowed by a ashing
battery icon.
Initialisation process This is a part of the initialisation process and is no cause for concern.
The pedalling frequency and kilocalories
readings have no bearing on reality
Slight deviations Depending on the level of assistance, a deviation of up to 20% is possible.
When the switched-o Pedelec is pushed,
the display will switch on automatically
for a few seconds before automatically
switching o again.
This behaviour is completely
normal.
In order to use the Pedelec, you will need to switch it on again manually after the automatic shutdown using
the easy-reach control.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalkhoff Neodrives Integrale at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalkhoff Neodrives Integrale in the language / languages: English as an attachment in your email.

The manual is 9,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalkhoff Neodrives Integrale

Kalkhoff Neodrives Integrale User Manual - German - 66 pages

Kalkhoff Neodrives Integrale User Manual - Dutch - 64 pages

Kalkhoff Neodrives Integrale User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info