694542
28
Zoom out
Zoom in
Previous page
1/40
Next page
28
5.2.1 Removing or resetting a
malfunction.
The automatic burner relay is equip-
ped with a safety setting per gas type
for the automatic ignition attempts.
Natural gas (G20, G25) has three auto-
matic ignition attempts and propane or
butane gas (G30) only has one ignition
attempt to ignite the burner. Should
the automatic ignition attempt(s) fail,
error code 08A and >ER< (Error) ap-
pear. This error code can be unlocked
and removed twice using the remote
control, before a 24-hour shut down is
initiated (error code 08F).
Carry out the following steps to unlock
the fireplace;
1. Press
approximately five times,
after which the “A” code disappears.
2. Check if the gas valve is open.
3. Inspect if the ionisation pen is unob-
structed by looking through the
glass.
4. Initiate the new ignition atempt.
Press
, until >OK< flashes in the
top left corner of the display.
5. You can repeat step 1-4 once.
6 If error code 08F appears you have
to wait 24 hours before you can
reattempt to ignite the gas fire.
The waiting time must be respected,
also after a power interruption.
5.2 Malfunctions
Malfunctions can be organised in five
categories:
1. Permanent malfunctions (indicated
as >F<). This malfunction cannot be
fixed automatically, the gas fire is
blocked for 24 hours (except for the
error code 02F).
2. Recovering malfunctions (indicated
as >ALARM< or >A<). Malfunction
that can recover automatically, if the
cause has been detected and fixed.
3. Communication malfunctions (indi-
cated as >E<). Malfunctions in the
communication connection between
the fireplace and the remote control
- these malfunctions can be fixed au-
tomatically when the remote control
is placed closer to the technical unit
of the fireplace.
Press 1 x
.
4. Signal malfunctions (indicated as
>NOLK 0 or 1< or a flashing RF icon
). The remote control does not
communicate with the fireplace. This
malfunction
cannot be fixed automatically.
5. Fireplace failure. The automatic
burner relay requires a “time-out”
every 24 hours (according to current
inspection regulations). During this
“time-out”, all applications of the
automatic burner relay are tested.
The fireplace is automatically swit-
ched off and stays down, until it is
turned on again manually.
28


Need help? Post your question in this forum.

Forumrules
1

Forum

kalfire-gp80-55c

Reset search

  • Can you have the flames without heat on the GP80 55C? Submitted on 9-9-2022 at 19:28

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalfire GP80-55C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalfire GP80-55C in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalfire GP80-55C

Kalfire GP80-55C User Manual - German - 44 pages

Kalfire GP80-55C User Manual - Dutch - 41 pages

Kalfire GP80-55C User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info