694530
16
Zoom out
Zoom in
Previous page
1/40
Next page
16
3. Place the two batteries on the com-
partment floor as indicated.
4. Close the compartment cover.
5. Press the
centre button and the
display will light up.
4.2 Using the iMatch remote
control
Range of the RF signal
The iMatch remote control uses a ra-
dio-frequency (RF) signal to transfer
information to the gas fire. The RF
signal is a safe signal for wireless com-
munication. The signal has a range of
approximately 10 metres as long as
there are no obstacles between the
remote control and the gas fire. Obsta-
cles such as walls and/or furniture can
negatively impact range. In some cases,
it can happen that the gas fire takes
longer to react. If the screen of the re-
mote control illuminates after a button
is pressed, this indicates that the RF
signal has been sent.
Key of symbols:
1. Indicates the time and status when
switching the appliance on or off:
OK - the fireplace is switched on.
WARM - the ignition programme
has been activated.
WAIT - the ignition programme is
starting up.
2. Day of the week in numbers
(1-7, Monday is 1).
a. (glow lamp) Indicator for the LED
lighting.
3. RF-signal, a flashing icon indicating
that the appliance is beyond the re-
ach of the remote control.
4. flame intensity indicator (hybrid fire)
4. Operation
The upcoming sections provide infor-
mation about the use of the gas fire:
- Replacing the batteries
- Using the iMatch remote control
- Setting the day and time
- Confirming the transmission
strength
- Switching the gas fire on and off
- Adjusting the flame intensity
- Selecting the thermostat or manual
operating programme
- Regulate the flame intensity by ther-
mostat
- Programming time segments
- Programme choice for the hybrid
LED lighting
- Activate/deactivate the hybrid LED
lighting and adjust
- Set the Natural Spark Generator
- Filling the Natural Spark Generator
- Configuring the iMatch app
- iMatch app settings
- Resetting the iMatch interface
- the iMatch app through the iMatch
interface
4.1 Replacing the batteries
Insert or replace the remote control AA
batteries.
A battery compartment is located at
the rear of the remote control. This can
hold two AA batteries. If the batteries
are almost flat, the battery icon beco-
mes visible or all symbols on the display
start to flash. Follow the steps below to
replace the batteries:
1. Slide the compartment cover down.
2. Remove the batteries (if in place).
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalfire G165-37C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalfire G165-37C in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalfire G165-37C

Kalfire G165-37C User Manual - German - 44 pages

Kalfire G165-37C User Manual - Dutch - 41 pages

Kalfire G165-37C User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info