694526
18
Zoom out
Zoom in
Previous page
1/40
Next page
18
flame intensity can also be displayed by
the flame intensity indicator.
The ECO mode has a modulating effect
on flame intensity (higher or lower).
This accentuates the visual effect
and user comfort of the flames, while
reducing the fire’s heat emission and
gas consumption by approximately
40%. Use the remote control to set the
flame intensity in “ECO mode” to 9,
after which the double flame icon
will
display on the screen. Adjust the flame
intensity as follows:
1. Press +or -to adjust flame intensity.
2. Release the + or - button.
3. Press the + button until the number 9
appears to switch on the ECO mode.
4.7 Selecting the thermostat or
manual operating programme
The flame intensity and the resulting
room temperature can be adjusted by
setting the remote control in manual or
thermostat mode. To ensure an accura-
te temperature reading, make sure the
remote control is outside of the fire’s
radiation range. For security reasons,
the thermostat mode will be automati-
cally switched off after 24 hours. If the
flames in the gas fire have been swit-
ched off, the programme will restart in
manual mode automatically when next
switched on.
1. By pressing P until the icon for
thermostat
or manual mode
begin to flash.
2. Press P again to selec the icon of
your choice.
3. Briefly press
to exit the menu.
3. Walk around the appliance at a dis-
tance of 3 to 4 metres to measure
the RFCK. If the RFCK shows a value
of 4, the transmission strength of the
remote control is good. If the value
shows as 2 or 3, the RFCK values are
acceptable. Transmission strength is
insufficient at a RFCK value of 1.
4. Confirm with
to exit the menu.
4.5 Switching the appliance on and o
Carry out the following steps to turn
the appliance on or off:
1. Press
until the >OK< icon in the
display appears and starts to flash.
2. Continue to press
and then press
briefly on
to activate the ignition
programme.
3. Release both buttons.
The word >WARM< will flash at the
top left of the display as confirmati-
on of activation.
4. Wait a number of seconds until you
hear a beep and the word >WAIT<
appears. The ignition programme will
start and the burner will automati-
cally ignite after approximately
20 seconds.
5. Wait until you hear a second beep.
The word >WAIT< will stop flashing
after the ignition programme.
6. The gas fire flame is alight and ope-
rational.
7. Press for approximately two seconds
to extinguish the gas fire flame.
4.6 Setting the flame intensity
The height of the flames can be adjus-
ted from high to low and is indicated on
the display by numbers 1 through 8. The
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalfire G120-41F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalfire G120-41F in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kalfire G120-41F

Kalfire G120-41F User Manual - German - 44 pages

Kalfire G120-41F User Manual - Dutch - 41 pages

Kalfire G120-41F User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info