29867
30
Zoom out
Zoom in
Previous page
1/36
Next page
LVT1266-001A
[B]
MICRO COMPONENT SYSTEM
UX-HB4
–Consists of CA-UXHB4 and SP-UXHB4
INSTRUCTIONS
UX-HB4[B]cover2.p65 04.8.5, 4:02 PM1
G-1
Warnings, Cautions and Others
CAUTION— (STANDBY/ON) button!
Disconnect the mains plug to shut the power off completely (all lamps
and indications go off). The (STANDBY/ON) button in any
position does not disconnect the mains line.
When the unit is on standby, the STANDBY lamp lights red.
When the unit is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the cable
is too short to reach a power point, then obtain an appropriate
safety approved extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical approved
type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the fuse
and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow
the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue : Neutral
Brown : Live
As these colours may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IF IN DOUBT—CONSULT A COMPETENT ELECTRICIAN.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to qualified
service personnel.
3. CAUTION: Visible and invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
CAUTION
Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
Do not place any naked flame sources, such as lighted
candles, on the apparatus.
When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Front view
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Side view
10 cm
15 cm
1 cm
15 cm
15 cm
1 cm
15 cm
15 cm
CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT ! UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEI.
GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT
IST. NICHT DEM STRAHL AUSSETZEN!
VARNING - OSYNLIG LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRR ÄR URKOPPLAD STRÅLEN ÄR FARLIG.
ADVARSEL -USYNLIG LASERSTRÅLING VED ÅBNING NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR STRÅLING.
UX-HB4
UX-HB4
Safety_UX_HB4[B].p65 04.8.5, 6:23 PM1
G-2
SAFETY INSTRUCTIONS
SOME DOS AND DONTS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards, but like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of
equipment) are properly made and in accordance with the manufacturers instructions. Switch off and withdraw the mains plug
when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way
switch off, withdraw the mains plug and consult your dealer.
DONT remove any fixed cover as this may expose dangerous voltages.
DONT leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended
operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DONT use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is
illegal to watch television whilst driving.
DONT listen to headphones at high volume as such use can permanently damage your hearing.
DONT obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DONT use makeshift stands and NEVER fix legs with wood screwsto ensure complete safety always fit the manufacturers
approved stand or legs with the fixings provided according to the instructions.
DONT allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
NEVER let anyone, especially children, push anything into holes, slots or any other opening in the casethis
could result in a fatal electrical shock.
NEVER guess or take chances with electrical equipment of any kindit is better to be safe than sorry!
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Safety_UX_HB4[B].p65 04.8.5, 6:23 PM2
1
Power sources
When unplugging the unit from the wall outlet, always pull
on the plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lenses inside the unit in the
following cases:
After starting to heat the room.
In a damp room.
If the unit is brought directly from a cold to a warm place.
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, then plug it in again.
Others
Should any metallic object or liquid fall into the unit,
unplug the AC power cord and consult your dealer before
operating any further.
If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
Rating label is placed on the exterior of the bottom.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
About This Manual
This manual is organized as follows:
This manual mainly explains operations using the
buttons on the remote control.
You can use the buttons both on the remote control and
on the unit for the same operations if they have the
same or similar names (or marks), unless mentioned
otherwise.
Basic and common information that is the same for many
functions is grouped in one place, and is not repeated for
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 9
to 11.
The following symbols are used in this manual:
Gives you warning and caution to prevent
damage or risk of fire/electric shock.
In addition, we put information here about
conditions which will prevent getting the best
possible performance from the unit.
Gives you information and hints you need to
know.
Precautions
Installation
Install in a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
Install the unit in a location with adequate ventilation to
prevent internal heat buildup.
Leave sufficient distance between the unit and the TV.
Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
01-05_UX-HB4[B]6.p65 04.8.5, 6:16 PM1
2
Contents
Location of the Buttons and Controls ....................... 3
Main Unit............................................................................... 3
Remote Control ..................................................................... 5
Getting Started............................................................ 6
Unpacking.............................................................................. 6
Connecting DAB Antenna ..................................................... 6
Connecting AM (MW) and FM Antennas ............................. 7
Connecting Speakers ............................................................. 7
Connecting Other Equipment ................................................ 8
Putting the Batteries into the Remote Control....................... 8
Common Operations .................................................. 9
Setting the Clock ...................................................................9
Turning On the Power .........................................................10
Turning Off the Unit Automatically (Auto Standby)........... 10
Selecting the Source ............................................................ 10
Adjusting the Volume .......................................................... 10
Fade-Out Muting (FADE MUTING) .................................. 11
Selecting the Sound Modes ................................................. 11
Reinforcing the Bass Sound ................................................11
Checking the Clock Time During Play................................ 11
Playing Back Discs .................................................... 12
Playing Back the Entire DiscNormal Play ......................12
Basic Disc Operations .........................................................13
Programming the Track Playing OrderProgram Play...... 14
Repeating TracksRepeat Play ..........................................15
Playing at RandomRandom Play ..................................... 15
Displaying the Remaining Time during Playback
(for Audio CD) .................................................................... 15
Displaying the Tag Information (for MP3 disc) .................. 15
Playing Back Tapes ................................................... 16
Playing Back a Tape ............................................................ 16
Listening to DAB Broadcast .................................... 17
What is DAB? ...................................................................... 17
Initial Scanning.................................................................... 17
Tuning in to a Station .......................................................... 18
Presetting Stations ............................................................... 18
Tuning in to a Preset Station................................................ 18
Arranging and Sorting the Station List................................ 19
Changing the Dynamic Range Control level (DRC) ........... 19
Changing the Display Information ...................................... 20
Refreshing the Station List .................................................. 20
Listening to FM and AM (MW) Broadcasts .......... 21
Tuning in to a Station .......................................................... 21
Presetting Stations ............................................................... 21
Tuning in to a Preset Station................................................ 22
Receiving FM Stations with RDS ....................................... 22
Changing the RDS Information ........................................... 23
Searching for Programs by PTY Codes (PTY Search) ....... 23
Using an External Equipment ................................. 24
Listening to the External Equipment ................................... 24
Recording .................................................................. 25
Recording on a Tape ............................................................ 25
Recording DiscsDisc Synchronized Recording............... 26
Using the Timers ....................................................... 27
Using Daily Timer and Recording Timer ............................ 27
Using Snooze Timer ............................................................ 28
Using Sleep Timer ............................................................... 29
Maintenance .............................................................. 30
Troubleshooting ........................................................ 31
Specifications ............................................................. 32
01-05_UX-HB4[B]6.p65 04.8.5, 6:16 PM2
3
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Main Unit
OPEN
COMPACT
DIGITAL AUDIO
DAILY TIMER/SNOOZE
1
3
2
Top view
Front view
STANDBY
CD
PHONES SCROLL DOWN SELECT SCROLL UP
4
#/8
AUX
PUSH OPEN
TAPE FM/AM/DAB AUX
VOLUME
+
UX-HB4
MICRO COMPONENT SYSTEM
AUTO REVERSE
REC
4
5
6
7
8
p
9
q
w
e
r
t
01-05_UX-HB4[B]6.p65 04.8.5, 6:16 PM3
4
Display window
Display window
1 Repeat indicators
, ALL, GR. (group)
2 REC indicators
(recording), (recording timer)
3 MP3 indicator
4 ST. (stereo) indicator
5 (sleep timer) indicator
6 BASS indicator
7 Timer indicators
, 1, 2, 3, DAILY, WEEKLY
8 Main display
9 DAB indicator
p RDS indicator
q (reverse mode) indicator
w 2 3 (tape direction) indicator
e PRGM (program) indicator
r EQ. (equalizer) indicator
t Frequency indicators
kHz, MHz
y RND. (random) indicator
u A.STANDBY indicator
See pages in parentheses for details.
Main unit
1 Disc cover (12)
2 ) OPEN (disc cover open) (12)
3 DAILY TIMER/SNOOZE button (28)
4 Remote sensor (5)
5 STANDBY lamp (10)
6 (STANDBY/ON) button (10)
7 Source buttons
CD #¥8, TAPE ¤‹, FM/AM/DAB, AUX
Pressing one of these buttons also turns on the unit.
8 PHONES jack (10)
9 Multi control buttons
SCROLL DOWN 4, SELECT 7, SCROLL UP ¢
p Cassette holder (16, 25, 26)
q Display window
w VOLUME + / control (10)
e AUX jack (8, 24)
r REC button (25, 26)
t PUSH OPEN (16, 25)
Continued
8
e r
t
yu
345 6
8
9p
q
12
7
w
01-05_UX-HB4[B]6.p65 04.8.5, 6:16 PM4
5
Remote Control
See pages in parentheses for details.
STANDBY
CD
PHONES SCROLL DOWN
4
#/8
SCROLL UPSELECT AUX
TAPE FM/AM/DAB AUX
VOLUME
+
When using the remote control, point it at the
remote sensor on the front panel.
1 STANDBY/ON button (10, 28)
2 SLEEP button (29)
3 TIMER button (27)
4 SET button (9, 27, 28)
5 CANCEL button (27, 28)
6 REV. (reverse) MODE button (16, 25, 26)
7 Source buttons
CD 3¥8, TAPE 2 3, FM/AM/DAB, AUX
Pressing one of these buttons also turns on the unit.
8 PROGRAM button (14, 18, 21)
9 RANDOM button (15)
p Multi control buttons
UP/PRESET GROUP , DOWN/PRESET GROUP
SEARCH/SCROLL DOWN, SELECT, SEARCH/
SCROLL UP
4, 7, ¢
q RDS/INFO button (17, 19, 20, 23)
w SCAN button (20)
e CLOCK button (9)
r A. (auto) STANDBY button (10)
t DISPLAY button (15, 20, 23)
y Number buttons (13, 14)
u REMAIN button (15)
BEAT CUT button (26)
i REPEAT button (15)
FM MODE button (21)
o VOLUME + / buttons (10, 28)
; FADE MUTING button (11)
a SOUND/HBS button (11)
RM-SUX
HB4 R
EMOTE CONTROL
STANDBY/ON
SLEEP
123
456
78
0
+10
9
TIMER
PRESET
GROUP
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
UP
7
/
SELECT
DOWN
PRESET
GROUP
SET
CANCEL
CD
PROGRAM
TAPE
RANDOM
FM/AM/DAB AUX
REPEAT
/FM MODE
REMAIN
/BEAT CUT
RDS/INFO SCAN SOUND/HBS
REV. MODE
FADE MUTING
VOLUME
CLOCK DISPLAY A. STANDBY
3/8
e
r
i
;
1
2
3
4
8
p
q
9
w
a
t
7
u
y
5
6
o
01-05_UX-HB4[B]6.p65 04.8.5, 6:16 PM5
6
1
Put the DAB antenna into the antenna cover
until the DAB antenna fits in with the
projection inside the antenna cover.
2
Connect the DAB antenna to the DAB ANT.
terminal.
To adjust the DAB antenna
Fix the antenna to pin up the wire with plastic eyelets
vertically.
If reception is poor
It is recommended to use the external antenna instead of supplied
antenna.
Getting Started
Unpacking
After unpacking, check to be sure that you have all the
following items.
The number in parentheses indicates the quantity of each
piece supplied.
DAB antenna (1)
AM (MW) loop antenna (1)
Remote control (1)
Batteries (2)
Antenna cover (1)
If any item is missing, consult your dealer immediately.
Do not connect the AC power cord until all other
connections have been made.
Continued
Connecting DAB Antenna
DAB ANT.
DAB ANT.
1
2
DAB ANT.
Eyelets
Antenna cover
(supplied)
DAB anntenna (supplied)
06-08_UX-HB4[B]6.p65 04.8.5, 6:16 PM6
7
Connecting Speakers
You can connect the speakers using the speaker cords.
1
Hold the clamp of the speaker terminal.
2
Insert the end of the speaker cord into the
terminal.
Match the polarity of the speaker terminals: red cord to
ª and black cord to ·.
3
Release your finger from the clamp.
IMPORTANT:
Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the unit.
DO NOT connect more than one speaker to one
speaker terminal.
Red
Red
Black
Black
Speaker
cord
Speaker
cord
1
2,3
Ò
Â
Left speakerRight speaker
AM (MW) loop antenna
(supplied)
FM antenna
1
2
Connecting AM (MW) and FM Antennas
Place the antenna away from the unit and adjust its position
for the best reception.
1
Adjust the position for the FM antenna for
the best reception.
2
Connect the supplied AM (MW) loop
antenna to the AM LOOP terminal.
For better reception of both FM and AM (MW)
Make sure the antenna conductors do not touch any other
terminals or connecting cords.
Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
AM LOOP
FM ANTENNA
Do not connect the AC power cord until all other connections have been made.
06-08_UX-HB4[B]5.p65 04.7.27, 7:04 PM7
8
Connecting Other Equipment
To connect an audio equipment
You can connect audio equipmentused only as a playback
device.
DO NOT connect any equipment while the power
is on.
DO NOT plug in any equipment until all
connections are complete.
For playing other equipment through this unit,
connect between the audio output jacks on the other
equipment and AUX jack by using audio cords with mini
plugs (not supplied).
When the audio equipment has pin jacks for audio output:
Be sure that the pin plugs of the audio cords are colored
white plugs and jacks are for left audio signals, and red ones
for right audio signals.
L
R
AUX
To
Audio equipment
To audio output
To audio output
1
2
3
AAA/UM-4/R03
Putting the Batteries into the Remote Control
Insert the batteriesAAA/UM-4/R03into the remote
control by matching the polarity (+ and ) on the batteries
with the + and marking on the battery compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
DO NOT use an old battery together with a new
one.
DO NOT use different types of batteries together.
DO NOT expose batteries to heat or flame.
DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time.
Otherwise, the remote control will be damaged
from battery leakage.
NOW you are ready to plug in the unit.
IMPORTANT:
Be sure to check that all connections have been made
before plugging in the power cord.
OR
Do not connect the AC power cord until all other connections have been made.
Speaker grille
Holes
Projections
To remove the speaker grilles
The speaker grilles are removable as the illustration below.
To remove the speaker grille, insert your fingers around the
projection at the top of the speaker grille, then pull gently
towards you while holding the side.
Do the same for the rest of projections one at a time.
To attach the speaker grille, put the projections of the
speaker grille into the holes of the speaker.
06-08_UX-HB4[B]5.p65 04.7.27, 7:04 PM8
9
Common Operations
Setting the Clock
Before operating the unit any further, first set the units clock.
When you plug in the power cord, 0:00 starts flashing on
the display.
You can set the clock when the unit is in standby mode.
On the remote control ONLY:
1
Press CLOCK for more than 2
seconds.
Clock setting appears on the display.
2
Press UP or DOWN to select the
clock synchronization setting,
then press SET.
On The units clock is adjusted
automatically with the FM RDS
signal on next time you tune in to an
FM station.
Off The units clock is adjusted manually.
The time system indication starts flashing.
3
Press UP or DOWN to adjust the
time system, then press SET.
12H The hour indication is displayed with
a 12-hour system (with AM or
PM).
24H The hour indication is displayed with
24-hour system.
The hour indication starts flashing.
4
Press UP or DOWN to adjust the
hour, then press SET.
When you press and hold UP or DOWN,
the hour indication changes continuously.
The clock is working even while setting.
The minute indication starts flashing.
5
Press UP or DOWN to adjust
the minute, then press SET.
When you press and hold UP or DOWN, the
minute indication changes continuously.
The day of the week indication starts flashing.
6
Press UP or DOWN to adjust
the day of the week, then press
SET.
Display brightness setting when the unit is in
standby mode appears on the display.
If you want to change the time setting, press
CANCEL repeatedly to return step
2
.
7
Press UP or DOWN to adjust
the brightness, then press SET.
The brightness level can be adjusted
between 0 (canceled) to 3 (most bright).
The greater number you set, the brighter the
display is.
The units clock starts working with the time you
adjusted.
When you unplug the AC power cord or if a power failure
occurs
The clock is reset to 0:00. If this happens, set the clock again.
The clock may gain or lose 1 to 2 minutes per month (when
the clock synchronization is turned off)
If this happens, set the clock again.
To adjust the clock
On the remote control ONLY:
1
Press CLOCK for more than 2 seconds
when the unit is in standby mode.
Clock setting appears on the display.
2
Repeat steps
2
to
7
of Setting the Clock
procedure.
CLOCK
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
SET
CLOCK
09-11_UX-HB4[B]6.p65 04.8.5, 6:16 PM9
10
VOLUME
Turning On the Power
To turn on the unit, press STANDBY/ON .
The STANDBY lamp on the unit goes off.
When you press the source buttonCD 3/8,
TAPE 2 3, FM/AM/DAB, and AUX, the unit
automatically turns on.
To turn off the unit (on standby), press STANDBY/ON
again.
The STANDBY lamp on the unit lights red.
The clock flashes on the display until you set the built-in
clock. After setting the clock, the clock time will appear on
the display while the unit is in standby mode.
A little power is always consumed even while the unit is in
standby mode.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
Turning Off the Unit Automatically
(Auto Standby)
Using Auto Standby, the unit automatically turns itself off (on
standby) about 3 minutes after playing back a disc or a tape.
You can also turn off the unit automatically by using the
Sleep Timer. (See page 29.)
On the remote control ONLY:
To activate Auto Standby, press A.STANDBY.
The A.STANDBY indicator appears on the display.
When the playback is stopped, the A.STANDBY
indicator starts flashing on the display.
To deactivate Auto Standby, press A.STANDBY again.
The A.STANDBY indicator goes off.
STANDBY/ON
A. STANDBY
Selecting the Source
To select the source, press CD 6, TAPE 2 3, FM/AM/
DAB, or AUX.
When you select CD or TAPE as the source, playback starts
automatically.
To operate the CD player, see pages 12 to 15.
To operate the tape deck, see page 16.
To operate the tuner (FM, AM (MW) or DAB), see pages 17
to 24.
To record on a tape, see pages 25 and 26.
To use an external equipment, see page 24.
Adjusting the Volume
You can adjust the volume level only while the unit is turned
on. The volume level can be adjusted between Volume
MIN, Volume 1 Volume 31, and Volume MAX.
The volume level has no effect on recording.
To increase the volume, press VOLUME + (or
turn VOLUME control clockwise on the unit).
To decrease the volume, press VOLUME (or
turn VOLUME control counterclockwise on the
unit).
When you press and hold either button, you can change the
volume level continuously.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume before
connecting or putting on the headphones.
When you turn off the unit with the volume level is
over Volume 20.
The volume level is automatically set to Volume 20 next time you
turn on the unit.
DO NOT turn off (on standby) the unit with the
volume set to an extremely high level; Otherwise,
the sudden blast of sound can damage your
hearing, speakers and/or headphones when you
turn on the unit or start playing any source.
REMEMBER you cannot adjust the volume level
while the unit is in standby mode.
Continued
09-11_UX-HB4[B]6.p65 04.8.5, 6:16 PM10
11
Fade-Out Muting (FADE MUTING)
On the remote control ONLY:
Press FADE MUTING.
The volume level decreases to the minimum level,
and Muting flashes on the display.
To release muting, press FADE MUTING again. The
volume level resumes to the previous level.
Selecting the Sound Modes
You can select one of the 4 sound modes.
This function also affects the sound from headphones.
This function only affects the playback sound, and does not
affect your recording.
On the remote control ONLY:
To select the sound modes, press SOUND/HBS
repeatedly.
Each time you press the button, the sound mode
changes as follows:
ROCK: Powerful sound emphasizing treble and bass.
POP: More presence in the vocals and midrange.
CLASSIC: Enriched sound with fine treble and ample bass.
JAZZ: Accented lower frequencies for jazz-type music.
FLAT: Equalizer effect is canceled.
When the sound mode is activated, the indicator lights up
on the display.
FADE MUTING
SOUND/HBS
Reinforcing the Bass Sound
You can boost the bass sound.
This function only affects the playback sound, and does not
affect your recording.
On the remote control ONLY:
Press and hold SOUND/HBS.
Each time you press and hold the button, HBS
turns on and off.
When the HBS is activated, the indicator lights up on
the display.
Checking the Clock Time During Play
On the remote control ONLY:
Press CLOCK.
Each time you press the button, the display
changes the clock indication and the normal
indication alternately. After changing the display
to the clock indication, operating any button or control also
changes the display to the normal indication.
CLOCK
ROCK
JAZZ
FLAT
CLASSIC
POP
(Canceled)
SOUND/HBS
09-11_UX-HB4[B]6.p65 04.8.5, 6:16 PM11
12
Playing Back the Entire Disc—Normal Play
1
Press ) OPEN on top of the unit.
The disc cover opens.
You can insert a disc while listening to another source.
2
Place a disc correctly with its label side up.
3
Close the disc cover gently.
4
Press CD 6.
The unit automatically turns on and the source
changes to the CD player.
When playing audio CD:
After loading the disc, the first track of the disc starts
playing.
When playing MP3 disc:
After loading the disc, total number of group and track on
the disc appear for a few seconds.
The disc automatically stops when the last track has
finished playing.
While Reading Disc Please Wait... appears on the
display
You cannot make any operation until the unit finishes reading the
disc.
While playing back an MP3 disc
ID3 Tag information (the name of the title, artist, and album up to
30 characters) will be shown on the display. When the name is too
long to be displayed at once, it is scrolled.
When a file does not belong in any folder, ROOT appears.
To stop playing, press 7.
CD Stop appears on the display.
The total track (or group) number and total
playing time appear on the display.
Playing Back Discs
This unit has been designed to play back the following
discsCD, CD-R, and CD-RW.
You can play back the discs containing the tracks in music
CD format or MP3 files in ISO 9660 format.
In this instruction, we call a disc recorded MP3 files MP3
disc, a folder contains MP3 files group, and an MP3 file
track.
When playing CD-Rs or CD-RWs
Before playing CD-Rs or CD-RWs, read their instructions
or cautions carefully.
User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-
ReWritable) can be played only if they are already
finalized.
This unit does not support multi-session discs.
This unit cannot play packet write discs.
Some CD-Rs or CD-RWs may not be played back on this
unit because of their disc characteristics, damage or stain
on them, or if the players lens is dirty.
CD-RWs may require a longer readout time. This is
because the reflectance of CD-RWs is lower than for
regular discs.
Notes for MP3 files
The player can only recognize files with .MP3 or .mp3
as the extensions, which can be in any combination of
upper and lower case. The file name needs to be up to 32
characters.
This unit recognizes files and folders on a disc in the
following conditions:
up to 640 MP3 files.
up to 99 folders (including the root folder).
up to 8th layers (including the root folder).
It is recommended that you record your material at a
44.1 kHz sampling rate, using the 128 kbps data transfer
rate.
Some MP3 files or discs may not be played back because
of their characteristics or recording conditions.
MP3 discs requires a longer readout time than normal discs
because of the complexity of the folder/file configuration.
MP3i and MP3 Pro are not available.
General notes
In general, you will have the best performance by keeping
your discs and the mechanism clean.
Store discs in their cases, and keep them in cabinets or on
shelves.
Keep the units disc cover closed when not in use.
Continued use of irregular shape discs (heart-shape,
octagonal, etc.) can damage the unit.
Good Not good
Elapsed playing time
CD
3/8
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Current track number
MP3
indicator
Elapsed
playing time
Current track number
in the selected group
Current group name Current track name
Continued
12-16_UX-HB4[B]6.p65 04.8.5, 6:16 PM12
13
Total track number Total playing time
When stop playing audio CD:
When stop playing MP3 disc:
Total playing time does not appear when MP3 disc is
loaded.
To remove the disc, press ) OPEN on the unit, then take out
the disc by holding it at the edges while pressing the units
pivot lightly.
If the disc cannot be read correctly (because it is scratched,
for example) or an unreadable CD-R or CD-RW is inserted
Playback will not start.
If no disc is inserted
No Disc appears on the display.
DO NOT open the disc cover by hand as it will be
damaged.
Current group number Current track number
Basic Disc Operations
While playing a disc, you can do the following operations.
To stop playing for a moment
During playback, press CD 3/8.
While pausing, Pause appears and elapsed playing
time flashes on the display.
To resume playing, press CD 3/8 again.
For Audio CD:
To go to another track
During playback, press ¢ or 4 (or
SCROLL UP ¢ or SCROLL DOWN
4 on the unit) repeatedly.
¢ (SCROLL UP ¢):
Skips to the beginning of the
next or succeeding tracks.
4 (SCROLL DOWN 4):
Goes back to the beginning of the
current or previous tracks.
Before or after playback, press CD 3/8 to start playback
after selecting the track to play back by pressing ¢ or 4.
CD
3/8
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
To go to another track directly using the number
buttons
On the remote control ONLY:
Pressing the number button(s) before or
during play allows you to start playing the
track number you want.
Ex.: For track number 5, press 5.
For track number 15, press +10, then
press 5.
For track number 20, press +10 twice,
then press 0.
To locate a particular point in a track
During play, press and hold ¢ or 4
(or SCROLL UP ¢ or SCROLL DOWN
4 on the unit).
¢ (SCROLL UP ¢):
Fast-forwards the tracks.
4 (SCROLL DOWN 4):
Fast-reverses the tracks.
For MP3 disc:
To go to another track
To select a track within a same group,
press ¢ or 4 (or SCROLL UP ¢ or
SCROLL DOWN 4 on the unit) repeatedly, then
press CD 3/8.
To select a track from a different group
1 Press PRESET GROUP or
PRESET GROUP to select a group
number.
As you press the button, group number
changes.
2 Press ¢ or 4 (or SCROLL UP
¢ or SCROLL DOWN 4 on the
unit) to select a track number.
As you press the button, track number
changes.
The track names also appear.
3 Press CD 3/8.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Selected group number
Selected track number
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
CD
3/8
123
456
78
0
9
+10
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Cursor
Cursor
12-16_UX-HB4[B]6.p65 04.8.5, 6:16 PM13
14
To go to another track directly using the number
buttons
You can select a track only within a same group.
On the remote control ONLY:
Pressing the number button(s) before or
during play allows you to start playing the
track number you want.
Ex.: For track number 5, press 5.
For track number 15, press +10, then
press 5.
For track number 20, press +10 twice, then
press 0.
If you select a track number does not exist in a group
The display for selecting a group number appears. In this case,
perform the same procedure to select a track as it is described on
page 13.
123
456
78
0
9
+10
Programming the Track Playing Order
Program Play
You can arrange the order in which tracks to play before you
start playing. You can program up to 99 tracks.
On the remote control ONLY:
1
Place a disc.
If the current source is not the CD player, press
CD 6, then 7 before going to the next step.
2
Press PROGRAM.
The PRGM (program) indicator and the program
step number appear and flash on the display.
3
Press ¢ or 4 to select the
track number, then press
PROGRAM.
You can also use the number button(s)
to select a track number.
For the operation of the number
buttons, see To go to another track
directly using the number buttons
on page 13.
PROGRAM
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PROGRAM
123
456
78
0
9
+10
CD
3/8
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
When you are programming from MP3
disc
Pressing PRESET GROUP
or PRESET
GROUP
selects the first track of each
group.
4
Repeat step
3
to program other tracks you
want.
5
Press 7.
Program Finish appears and the PRGM
indicator remains lit on the display. The
program is stored in the memory.
6
Press CD 3/8.
The tracks are played in the order you have
programed.
If you try to program a 100th track
Program Full will appear on the display.
To stop playing, press 7.
To check the program contents
While the PRGM indicator is lit on the
display, you can check the program contents
by pressing ¢ or 4 repeatedly before or
after playback.
To add tracks in the program, repeat steps
2
and
3
of the programming procedure. The track will be
added on the last step.
To clear the program
Press 7 before or after playback when the
PRGM indicator is lit on the display.
Clear Program appears and the PRGM
indicator disappears from the display. All the
memory contents will be erased (resumes to
Normal Play).
The programmed tracks are also erased in the following
cases:
Pressing ) OPEN to open the disc cover
Turning off the unit
Changing the source
During Program Play
Auto Standby function does not take effect.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Continued
12-16_UX-HB4[B]6.p65 04.8.5, 6:16 PM14
15
Repeating TracksRepeat Play
You can have all the tracks, the program or individual track
currently playing, repeat as many times as you like.
On the remote control ONLY:
Press REPEAT.
Each time you press the button, Repeat Play
changes as follows, and the following repeat
indicators light up on the display:
When playing back audio CD:
: Repeats one track.
ALL: Repeats all the tracks.
In Program Play, repeats all the tracks in the
program.
When playing back MP3 disc:
: Repeats one track.
In Random Play, this function is not available.
GR.: Repeats all the tracks in a group.
In Program Play and Random Play, this
function is not available.
ALL: Repeats all the tracks.
In Program Play, repeats all the tracks in the
program.
To cancel Repeat Play, press REPEAT repeatedly
until the repeat indicator goes off.
/FM MODE
REPEAT
Canceled
ALL
Repeat indicators
ALL
GR.
Canceled
/FM MODE
REPEAT
Playing at RandomRandom Play
You can play the tracks at random.
On the remote control ONLY:
Press RANDOM.
The RND. indicator lights up on the display.
RANDOM
To exit from Random Play, press 7 or
RANDOM.
The RND. indicator goes off.
You cannot activate the Random Play
function during Program Play.
Displaying the Remaining Time during
Playback (for Audio CD)
When playing back audio CD, you can display the remaining
time of the current track/disc and the elapsed time of the
current track/disc during playing.
On the remote control ONLY:
Press REMAIN repeatedly.
Each time you press the button, the display
changes as follows:
Track Rem. Play: Shows the remaining time of the current
track.
Disc Time Play: Shows the remaining time of the disc.
Disc Rem. Play: Shows the elapsed time of the disc.
Normal indication: Shows the elapsed time of the current
track.
Displaying the Tag Information (for MP3 disc)
You can display the ID3 Tag information of the MP3 disc.
On the remote control ONLY:
Press Display during MP3 playback.
Each time you press the button, the display changes
as follows:
Title: Shows name of the track.
Artist: Shows name of the artist.
Album: Shows name of the album.
Normal indication: Shows the group name and track name
currently played back.
If the file does not have any information, the second line
will be displayed in blank.
/BEAT CUT
REMAIN
RND. indicator
DISPLAY
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Title
Normal
indication
Album
Artist
Track Rem. Play Disc Time Play
Disc Rem. Play
Normal
indication
12-16_UX-HB4[B]6.p65 04.8.5, 6:17 PM15
16
PUSH OPEN
If no cassette is inserted when you press TAPE ¤
No TAPE appears on the display.
To stop playing, press 7.
To fast-wind to the left or to the right,
press ¢ or 4 (or ¢ or 4 on the
unit).
Fast Wind appears and the tape direction
indicator ( 33 or 22 ) scrolls on the display.
To remove the cassette, press PUSH OPEN
on the unit while playback is stopped.
To play both sidesReverse Mode
You can set the deck to play just one side of a tape, both sides
once, or both sides continuously.
On the remote control ONLY:
Press REV. MODE (Reverse Mode).
Each time you press the button, the Reverse
Mode changes as follows:
: The deck automatically stops after playing both
sides of the tape.
: The deck continues to play both sides of the tape 10
times, then stops playback automatically.
: The deck automatically stops after playing one side
of the tape.
DO NOT turn off the unit while playing back or
recording a tape. The cassette deck or tapes
may be damaged.
The use of C-120 or longer tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinch
rollers and the capstans.
This unit is not compatible with type II and type
IV tapes.
Playing Back a Tape
You can play back type I tapes only.
1
Press PUSH OPEN.
The cassette holder opens.
2
Put a cassette in with the exposed part of the
tape down.
3
Close the cassette holder gently.
When a tape is inside of the cassette holder, the tape
direction indicator ( 3 ) lights up on the display.
4
Press TAPE ¤ .
Playback starts (if the unit has been on
standby, the unit automatically turns on).
TAPE Play appears and the tape direction
indicator ( 3 or 2 ) starts flashing slowly on
the display.
Each time you press the button, the tape direction
changes:
3: plays the front side.
2: plays the reverse side.
When the tape plays to the end, the deck automatically
stops if the Reverse Mode is set to or . (See To
play both sidesReverse Mode.)
Playing Back Tapes
SCROLL DOWN SELECT
4 7 ¢
SCROLL UP
SCROLL DOWN
4 7 ¢
SCROLL UP
SELECT
PUSH OPEN
REV. MODE
TAPE
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
12-16_UX-HB4[B]6.p65 04.8.5, 6:17 PM16
17
Listening to DAB Broadcast
What is DAB?
Digital Audio Broadcasting (DAB) is a radio which carries
information in digital format enabling near CD-quality audio
sound. Also DAB enables broadcasters to transmit additional
data along with the audio.
DAB structure
DAB is broadcast as groups of data called ensembles. Each
ensembles can contain a number of stations (services) and
each station contains services.
The unit can receive ensembles in frequency band III
(174.928 239.200 MHz) and store their services in each
ensemble. The number of ensemble you receive varies
depending on your location. Band III is divided into 41
channels identified as 5A to 13F. Each channel can contain
one ensemble. Channels allocated to the United Kingdom are
in the range 11B to 12D.
Ensembles and stations have labels (names) which are used to
identify them. Instead of memorizing a particular frequency
to listen to a program you like, you can simply select a
program by the station name.
About the display symbol
While tuning in to a station, the following symbols may
appear by the side of the station names:
The tuned station is sorted as one of your ten
favorite stations. (See page 19 for details.)
? The tuned station is not available or not active.
>> The tuned station is a primary station with
secondary services.
<< The tuned station is a secondary station.
Initial Scanning
When you change the source to DAB for the first time, the
unit performs the initial scanning to search for the available
stations.
Press FM/AM/DAB repeatedly to select
DAB.
Welcome To Digital Radio scrolls and the initial
scanning starts.
When the progress bar reaches to the right side, the initial
scanning finishes.
Once the scanning is completed, all the available stations
are listed by numerical, then alphabetical order and stored
in the memory.
The unit will tune in to the first listed station.
If you stop the scanning by pressing any button,
no station is listed. In this case, do the local or full scan (see
page 19).
When there is no available station,
Station Not Available appears. The unit enters to the
manual scanning mode (see below).
Manual tuning
If the scanning does not go successfully, you can perform the
manual tuning.
On the remote control ONLY:
1
Press RDS/INFO.
2
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select Manual Tune.
Each time you press the button, the
option changes as follows:
* See page 19 for details.
3
Press SELECT.
A station with frequency appears.
FM/AM/DAB
DAB indicator
Progress bar
Service Order DRC Value
Manual Tune
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
RDS/INFO
Ensembles
(Primary) service
Secondary service
**
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM17
18
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
4
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select a station.
Each time you press the button, the station
changes step by step.
5
Press SELECT.
Signal reception indicator and the
current signal strength level appear (filled
blocks across from left to right).
If
the signal strength level
does not reach to the signal
reception indicator, you cannot listen to the station well.
In this case, adjust the position of the antenna.
6
Press SELECT again.
A station is tuned in.
For the description of information sent from the station,
see page 20.
Tuning in to a Station
1
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select a station.
The list of the station appears.
2
Press SELECT to tune in to the
selected station.
The unit does not tune in to the station
until you press SELECT.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
On the remote control ONLY:
1
Tune in to the station you want to preset.
2
Press PROGRAM.
An available preset number starts flashing on the
display.
3
Press PRESET GROUP or
PRESET GROUP to select a
preset number, then press
PROGRAM.
The preset station is stored in memory.
4
To preset more stations, repeat steps
1
to
3
above, allocating a different preset number to
each station.
Storing a new station on an already assigned number
erases the previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The preset stations will remain in the unit.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PROGRAM
PROGRAM
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Tuning in to a Preset Station
On the remote control ONLY:
1
Press FM/AM/DAB to select DAB.
The unit automatically turns on and tunes in to
the previously received DAB station.
2
Press PRESET GROUP or
PRESET GROUP repeatedly
to select a preset number.
To tune in to a preset station directly using the number
buttons
On the remote control ONLY:
Pressing the number button(s) allows you
to select the preset number you want.
Ex.: For preset number 5, press 5.
For preset number 10, press +10,
then press 0.
When you press a number with no preset station
Empty Preset appears on the display.
FM/AM/DAB
Presetting Stations
You can preset 10 DAB stations manually.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step
2
.
123
456
78
0
9
+10
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Signal reception indicator
Signal strength level
Channel and frequency
Information sent from the station (Ex. program type)
Station name
Continued
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM18
19
Arranging and Sorting the Station List
You can arrange or sort the station list which appears on the
display when you browse to look for a station.
On the remote control ONLY:
1
Press RDS/INFO.
2
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select Service Order.
Each time you press the button, the option
changes as follows:
* See page 17 for details.
** See the right column for details.
3
Press SELECT.
An option appears on the display.
4
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select a desired option.
Each time you press the button, the option
changes as follows:
Fav(Favorite) Station:
The DAB tuner makes a list of the 10
stations you most listened to as your
favorite station. The 1st station you
listened to most comes first. After
selecting this option, appears
after the name of your favorite
station.
Alphanumeric: The order is arranged by the station
name. The name begins with
numerical characters comes first,
then with alphabetical characters
comes second. (Initial setting)
Service Order DRC Value
Manual Tune
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
RDS/INFO
Prune Station
Fav(Favorite) Station
Presets
Ensemble
Alphanumeric
Active Station
Active Station: The order is arranged by the activity
of stations. All the active stations can
be received come top of the list. The
stations cannot be received sends to
the bottom of the list.
Ensemble: The order is arranged by the
ensemble name of stations.
Prune Station: The DAB tuner removes the stations
from the list which do not have
service in your area.
Presets: You can select this option only after
you made a list by selecting Fav
Station. The DAB tuner allocates
your 10 favorite stations to preset
channels 1 to 10.
The 1st station you listened to most
is preset to preset channel 1, and the
2nd station is preset to preset
channel 2, etc,.
5
Press SELECT.
Changing the Dynamic Range Control level (DRC)
You can change the dynamic range control level to
compensate the compression difference between stations.
On the remote control ONLY:
1
Press RDS/INFO.
2
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select DRC Value.
Each time you press the button, the option
changes as follows:
* See page 17 for details.
** See the left column for details.
3
Press SELECT.
The DRC level setting appears on the display.
*
Service Order DRC Value
Manual Tune
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
RDS/INFO
*
Current level
Available adjustment level
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
**
**
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM19
20
DISPLAY
Refreshing the Station List
For tuning in to the new available DAB stations, you need to
refresh the station list.
There are two ways for searching stations:
Local search: Performs the search for stations on band III
in the United Kingdom.
Full search: Performs the wider search for stations than
local search. When you bring this unit
outside of the United Kingdom, use this
search. This search is used mainly for the
use of outside of the United Kingdom.
For local search:
Press SCAN briefly.
For full search:
Press and hold SCAN for more than 2
seconds.
The search begins.
The number of found stations is counted as the search is
being proceeded.
When the progress bar reaches to the right side of the display,
the search finishes. After the search, the unit tunes in to the
previously tuned station.
To clear the stored memory, press RDS/INFO for
more than 2 seconds. Then, press SELECT after the
message appears on the display.
The DAB tuner starts the initial scanning.
SCAN
Number of the found stationsProgress bar
Changing the Display Information
You can change the information appears on the display.
On the remote control ONLY:
Press DISPLAY.
Each time you press the button, the information
changes as follows:
DLS (Dynamic Label Segment):
Text messages sent from the station
(Initial Setting)
Program Type: Types of broadcast programs
Ensemble: Type of ensemble
Time and Date: Time and day sent from the station
Channel and Frequency:
Channel number and transmission
frequency
Signal Information
Program Type
Sig.(Signal) Quality
Channel and Frequency
Ensemble
Time and Date
DLS
4
Press SEARCH/SCROLL UP
or SEARCH/SCROLL DOWN
to select a desired compression
level.
Each time you press the button, the DRC
level changes as follows:
DRC 0: The DRC level adjustment is
canceled.
DRC 1/2: Medium level of compression is
applied.
DRC 1: Maximum level of compression is
applied. (Initial setting)
5
Press SELECT.
DRC 1 DRC 1/2
DRC 0
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Signal Information:
Digital bit rate (kbps) and signal mode
(stereo or mono)
Sig.(Signal) Quality:
Reception measurement sent from the
station (100 is the best reception)
When the value is below 100, adjust
the position of the antenna for the
better reception.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
RDS/INFO
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM20
21
Tuning in to a Station
You can search for the station by either automatically or
manually.
Auto Tuning
1
Press FM/AM/DAB repeatedly to
select either FM or AM (MW).
The unit automatically turns on and tunes in to
the previously received station.
If the station previously selected is stored in a preset
number, the preset number will also appear.
2
Press and hold ¢ or 4 (or
SCROLL UP ¢ or SCROLL
DOWN 4 on the unit) for
about 2 seconds until Search..
appears on the display.
Searching.. appears and the unit starts searching
for stations.
¢ (SCROLL UP ¢): Increases the frequencies.
4 (SCROLL DOWN 4):
Decreases the frequencies.
The search stops when a station of sufficient signal
strength is tuned in.
If an FM program is broadcast in stereo, the ST (stereo)
indicator lights up on the display (only when the
reception is good).
To stop during searching, press ¢ or 4 (or SCROLL
UP ¢ or SCROLL DOWN 4 on the unit).
Manual Tuning
1
Press FM/AM/DAB repeatedly to
select either FM or AM (MW).
2
Press and hold ¢ or 4 (or
UP ¢ or DOWN 4 on the
unit) for more than 3 seconds.
¢ (SCROLL UP ¢): Increases the
frequencies.
4 (SCROLL DOWN 4): Decreases the
frequencies.
The frequency keeps changing quickly.
To stop during searching, release the button.
When you repeatedly press ¢ or 4 (or SCROLL
UP ¢ or SCROLL DOWN 4 on the unit)
The frequency changes step by step.
Presetting Stations
You can preset 20 FM and 10 AM (MW) stations manually.
In some cases, test frequencies have been already stored
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You
can preset the stations you want into memory by following
the presetting method.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step
2
.
On the remote control ONLY:
1
Tune in to the station you want to preset.
See Tuning in to a Station on the left column.
2
Press PROGRAM.
An available preset number starts flashing on the
display.
3
Press PRESET GROUP or
PRESET GROUP to select a
preset number, then press
PROGRAM.
Station Stored appears and the preset station
is stored in memory.
FM/AM/DAB
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
/FM MODE
REPEAT
Listening to FM and AM (MW) Broadcasts
PROGRAM
To change the FM reception mode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE so that the Mono
appears on the display. Reception will improve.
To restore the stereo effect, press FM MODE
again so that Stereo appears and the ST (stereo) indicator
lights up on the display. In stereo mode, you can hear stereo
sound when a stereo program is broadcast.
The stereo effect also restores when:
changing the band (AM (MW), or DAB).
changing the station frequency.
changing the playing source.
turning off (or on) the unit.
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
FM/AM/DAB
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM21
22
123
456
78
0
9
+10
FM/AM/DAB
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
4
To preset more stations, repeat steps
1
to
3
above, allocating a different preset number to
each station.
Storing a new station on an already assigned number
erases the previously stored one.
When you unplug the AC power cord or if a power
failure occurs
The preset stations will remain in the unit.
Tuning in to a Preset Station
On the remote control ONLY:
1
Press FM/AM/DAB to select either
FM or AM (MW).
The unit automatically turns on and tunes in to
the previously received station.
2
Press PRESET GROUP or
PRESET GROUP repeatedly
to select a preset number.
To tune in to a preset station directly using the number
buttons
On the remote control ONLY:
Pressing the number button(s) allows you
to select the preset number you want.
Ex.: For preset number 5, press 5.
For preset number 15, press +10, then
press 5.
For preset number 20, press +10
twice, then press 0.
Receiving FM Stations with RDS
RDS (Radio Data System) allows FM stations to send an
additional signal along with their regular program signals.
For example, the stations send their station names, as well as
information about what type of program they broadcast, such
as sports or music, etc.
With the unit, you can receive the following types of RDS
signals.
Radio Text:
Text messages sent from the station
Program Type:
Types of broadcast programs.
RDS Time:
Time and day of the week sent from the station
PI (Program Identification) Code:
Identification number of a program.
More about RDS
Some FM stations do not provide RDS signals.
RDS services vary among FM RDS stations. For details on RDS
services in your area, check with local radio stations.
RDS may not work correctly if the received station is not
transmitting the signals properly or if the signal strength is weak.
Continued
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM22
23
Searching for Programs by PTY Codes
(PTY Search)
One of the advantages of RDS is that you can locate a
particular kind of program by specifying the PTY codes.
For details on the PTY codes, see Description of the PTY
codes on the next page.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step
1
.
On the remote control ONLY:
1
Press RDS/INFO.
PTY code setting appears.
2
Press UP or DOWN repeatedly
until the PTY code you want
appears on the display.
Each time you press the buttons, the PTY
codes change as follows:
None
j
News
j
Current Affairs
j
Information
j
Sport
j
Education
j
Drama
j
Cultures
j
Science
j
Varied Speech
j
Pop Music
j
Rock Music
j
Easy Listening
j
Light Classic M
j
Serious Classic
j
Other Music
j
Weather & Metr
j
Finance
j
Childrens progs
j
Social Affairs
j
Religion
j
Phone In
j
Travel & Touring
j
Leisure & Hobby
j
Jazz Music
j
Country Music
j
Nation Music
j
Oldies Music
j
Folk Music
j
Documentary
j
Alarm Test
j
Alarm Alarm!
j
(back to the beginning)
3
Press SEARCH/SCROLL UP or
SEARCH/SCROLL UP (or
SCROLL UP or SCROLL
DOWN on the unit).
The unit starts searching for the program.
If no program is found, The PTY No Found
appears on the display and the unit returns to the last
received station.
To stop searching any time during the process, press RDS/
INFO while searching.
If you preset a station while PTY Search is being
carried out
PTY Search may not stop. If this happens, press RDS/INFO to stop
searching.
RDS/INFO
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
Changing the RDS Information
You can see RDS information on the display while listening
to an FM station.
On the remote control ONLY:
Press DISPLAY.
Each time you press the button, the display
changes to show the following information:
If no RDS signals are sent by a station
No RDS signal appears on the display.
On the characters displayed
The display cannot show accented letters; for example, A may
represent accented As like “Á, Â, Ã, À, Ä and Å.
DISPLAY
RDS Time
PI Code
Radio Text
Program Type
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM23
24
Listening to the External Equipment
You can listen to the external equipment such as MD
recorder, cassette deck, or other auxiliary.
First, make sure that the external equipment is properly
connected to the unit. (See page 8.)
1
Set the volume level to the minimum position.
2
Press AUX.
AUX appears on the display.
3
Start playing the external equipment.
4
Adjust the volume level to the level you want
to listen to.
Using an External Equipment
AUX
To exit AUX mode, select other source.
For operation of the external equipment
Refer to its instructions.
Description of the PTY codes
News News.
Current Affairs Topical program expanding or enlarging upon
the newsdebate, or analysis.
Information Program the purpose of which is to impart
advice in the widest sense.
Sport Program concerned with any aspect of sports.
Education Educational programs.
Drama All radio plays and serials.
Cultures Programs concerning any aspect of national or
regional culture, including language, theater, etc.
Science Programs about natural sciences and technology.
Varied Speech Used for mainly speech-based programs such as
quizzes, panel games and personality interviews.
Pop Music Commercial music of current popular appeal.
Rock Music Rock music.
Easy Listening Current contemporary music considered to be
easy-listening.
Light Classic M Instrumental music, and vocal or choral works.
Serious Classic Performances of major orchestral works,
symphonies, chamber music, etc.
Other Music Music not fitting into any of the other categories.
Weather & Metr Weather reports and forecasts.
Finance Stock Market reports, commerce, trading etc.
Childrens progs Programs targeted at a young audience.
Classification of the PTY codes for some FM stations
may be different from the above list on this page.
Social Affairs Programs about sociology, history, geography,
psychology and society.
Religion Religious programs.
Phone In Involving members of the public expressing their
views either by phone or at a public forum.
Travel & Touring Travel information.
Leisure & Hobby Programs about recreational activities.
Jazz Music Jazz music.
Country Music
Songs which originate from, or continue the
musical tradition of the American Southern States.
Nation Music
Current popular music of the nation or region in
that countrys language.
Oldies Music
Music from the so-called golden age of
popular music.
Folk Music Music which has its roots in the musical culture
of a particular nation.
Documentary Program concerning factual matters, presented in
an investigative style.
Alarm Test Broadcasts for testing emergency broadcast
equipment or receiver.
Alarm Alarm! Emergency announcement.
None No program type, undefined program, or
difficult to categorize into particular types.
17-24_UX-HB4[B]6.p65 04.8.5, 6:17 PM24
25
3
Start playing the sourceFM, AM (MW),
DAB or auxiliary equipment connected to
AUX jack.
When the source is FM, AM (MW), or DAB, tune in to
the station you want to record.
When recording from discs, see Recording Discs
Disc Synchronized Recording on page 26.
4
Press REC (recording).
The REC indicator appears and 3 indicator
lights up on the display.
5
Press TAPE ¤ .
3 indicator starts flashing and the recording
starts.
If no cassette is inserted when you press REC
No TAPE appears on the display.
If a protected tape is inserted when you press REC
TAPE Protect appears on the display.
To stop recording for a moment, press REC.
The recording is paused. To resume recording, press
TAPE ¤ .
To stop recording, press 7.
The recording stops.
To remove the cassette, press PUSH OPEN
while recording is stopped.
To record on both sidesReverse Mode
On the remote control ONLY:
Press REV. MODE (reverse mode) until
or is lit on the display.
When using the Reverse Mode for recording,
lights up and start recording in the forward ( 3 )
direction first.
To cancel the Reverse Mode, press REV.MODE repeatedly
until is lit on the display.
IMPORTANT:
It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast or cable program and in any
literary, dramatic, musical, or artistic embodied
therein.
The recording level is automatically set correctly, so it is
not affected by the other sound settings. Thus, during
recording you can adjust the sound you are actually
listening to without affecting the recording level.
If recordings you have made have excessive noise or static,
the unit may be too close to a TV. Increase the distance
between the TV and the unit.
You can only use type I tape for recording.
DO NOT turn off the unit while playing back or
recording a tape. The cassette deck or tapes
may be damaged.
DO NOT use type II and type IV tapes since the
unit is not compatible with such tapes.
The use of C-120 or longer tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinch
rollers and the capstans.
At the start and end of cassette tapes
There is leader tape which cannot be recorded onto. Thus, when
recording from discs, FM/AM (MW)/DAB broadcasts, or external
equipment, wind the leader tape first to ensure that the recording
will be made without losing any music.
To protect your recordings
Cassettes have two small tabs on the back to protect against
unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
Recording
Adhesive tape
Recording on a Tape
On the unit ONLY:
1
Put a recordable cassette in with the exposed
part of the tape down.
See also page 16.
2
Close the cassette holder gently.
REC
REC
PUSH OPEN
REV. MODE
SCROLL DOWN SELECT
4 7 ¢
SCROLL UP
TAPE
25-26_UX-HB4[B]6.p65 04.8.5, 6:17 PM25
26
To stop recording for a moment, press REC.
Both the disc playback and tape recording are
paused. To resume recording, press TAPE ¤ .
To stop recording, press 7.
The recording stops and the disc
playback is paused.
To record on both sidesReverse Mode
On the remote control ONLY:
Press REV. MODE (reverse mode)
repeatedly until or is lit on the
display.
When using the Reverse Mode for Disc
Synchronized Recording, lights up and the recording
starts in the forward ( 3 ) direction first. When the tape
reaches its end, the disc playback is paused until the tape
recording changes to the reverse direction, then the
recording continues.
To cancel the Reverse Mode, press REV. MODE repeatedly
until is lit on the display.
When making Sleep Timer settings while doing Disc
Direct Recording
Set enough time to allow for the disc to finish playing; otherwise,
the power will go off before recording is completed.
Recording Discs
Disc Synchronized Recording
You can start disc play and recording at the same time.
On the unit ONLY:
1
Put a recordable cassette in with the exposed
part of the tape down.
See also page 16.
2
Close the cassette holder gently.
3
Press CD /8 to select the CD
player as the source.
4
Press 7 to stop the disc
playback.
You can make a program (see page
14) if you want.
5
Press REC (recording).
3 indicator lights up on the display.
6
Press TAPE ¤ .
Sync. Record appears and 3 indicator starts
flashing slowly on the display.
Disc playback and tape recording starts
automatically.
If no cassette is inserted when you press REC
No Tape appears on the display.
If a protected tape is inserted when you press REC
Protect appears on the display.
REC
REC
REV. MODE
CD
#/8
TAPE
SCROLL DOWN SELECT
4 7 ¢
SCROLL UP
SCROLL DOWN SELECT
4 7 ¢
SCROLL UP
/BEAT CUT
REMAIN
To reduce the beatBeat Cut
On the remote control ONLY:
If the beats are heard while recording an AM
(MW) broadcast, press BEAT CUT repeatedly until
the beats are reduced.
Each time you press the button, the display
alternates between Beat Cut 1 and Beat Cut 2.
25-26_UX-HB4[B]6.p65 04.8.5, 6:17 PM26
27
Using the Timers
There are four timers availableDaily Timer (Just Once,
Every Day, Weekly), Recording Timer, Snooze Timer, and
Sleep Timer.
Before using these timers, make sure the built-in clock is
set correctly (see page 9).
Using Daily Timer and Recording Timer
You can set the timer whether the unit is on or off.
How the Timer actually works
When the on-time comes, the unit automatically turns on (the
[timer] indicator flashes and continues flashing while the
timer is operating). Then, when the off-time comes, the unit
automatically turns off (standby). The timer setting remains
in memory until you change it.
When the (timer) and 1, 2, 3, or with DAILY or
WEEKLY indicators are lit on the display, the timer acts as
the Daily Timer. Once the timer has been set, it will be
activated at the same time on the selected day and
automatically turns off (standby) after 60 minutes everyday
until the timer is deactivated.
When the (timer) and the REC indicators are lit on the
display, the timer acts as the Recording Timer. After the
timer-recording finishes, the details of the setting remain
stored but the timer is turned off.
Before you start...
When using TUNER as the source to play, make sure to
select the desired station before turning off the power.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start again from step
1
.
TIMER
On the remote control ONLY:
1
Press TIMER repeatedly to select the
timer you want to adjust and activate
1, 2, 3, or Rec.
The timer setting indicator and hour indication start
flashing on the display.
Each time you press the button, the display changes as
follows:
2
Set the on-time you want the
unit to turn on.
(1) Press UP or DOWN to set the hour,
then press SET.
(2) Press UP or DOWN to set the minute,
then press SET.
If you want to change the time setting, press
CANCEL.
If you are setting the Daily Timer, the mode
setting appears on the display.
\ Go to step
4
.
If you are setting the Recording Timer,
the off-time setting appears on the display.
3
For the Recording Timer ONLY:
Set the off-time you want the unit to turn off.
(1) Press UP or DOWN to set the hour, then press SET.
(2) Press UP or DOWN to set the minute, then press SET.
If you want to change the time setting, press
CANCEL.
\ Go to step
5
.
4
For the Daily Timer ONLY:
Select the timer repeat mode.
Press UP or DOWN to select the mode
setting, then press SET.
SET
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
PRESET
GROUP
PRESET
GROUP
UP
DOWN
SEARCH/
SCROLL
DOWN
SEARCH/
SCROLL
UP
/
SELECT
12 3
REC.
Normal indication
SET
27-29_UX-HB4[B]6.p65 04.8.5, 6:17 PM27
28
Each time you press the button, the timer repeat mode
changes as follows:
If you select Every Day or from Mon to Fri, the
indicator corresponding to the selected mode lights up
on the display.
5
Press UP or DOWN to select the source to
play.
Each time you press the button, the source changes as
follows:
For Recording Timer:
For Daily Timer:
Make sure the playing source (either a cassette tape or a
disc) is inside when you select TAPE or CD for
Daily Timer.
If you want to change the time setting, press CANCEL
repeatedly to return step
2
.
6
Press SET.
The display returns to the normal indication.
7
Press VOLUME +/ to adjust the
volume for the on-time.
Even if you set the volume level to over
Volume 20, the volume level is
automatically set to Volume 20 when the
timer on-time comes.
8
Press STANDBY/ON to turn off
the unit if you have set the timer with
the unit turned on.
On the unit ONLY:
To activate the timer, press and hold
DAILY TIMER/SNOOZE on the unit
repeatedly to select the timer number you want.
To deactivate the timer, press and
hold DAILY TIMER/SNOOZE.
Each time you press and hold the
button, the timer setting changes as follows:
SET
VOLUME
STANDBY/ON
12 3
REC.
Canceled
To change the timer, repeat steps
1
to
6
on pages 27 and this
page.
To activate the Daily Timer again without changing the
setting, press DAILY TIMER/SNOOZE on the unit
repeatedly to select the timer number you want.
To cancel the timer while it is working, press STANDBY/
ON .
If the unit is already turned on when the timer on-time
comes
The timer does not work.
When you unplug the AC power cord or if a power
failure occurs
The timer setting remains. Set the built-in clock and activate the
timer again.
Using Snooze Timer
The Snooze Timer turns off the unit (standby) only for 5
minutes while Daily Timer is in operation.
You can set the Snooze Timer only while the Daily Timer is
in operation.
On the unit ONLY:
Press DAILY TIMER/
SNOOZE while Daily Timer
is in operation.
The unit turns off (standby) and the Snooze with
countdown timer appear on the display.
After 5 minutes, the unit automatically turns on with the
source you selected in step
4
on page 27.
If the unit is turned on when the Snooze Timer is
working
Both Snooze Timer and Daily Timer will be canceled.
If you set the Snooze Timer when there is less than 5
minutes until the Daily Timer off-time
The unit will not turn on even when 5 minutes passed.
When you unplug the AC power cord or if a power
failure occurs
The timer will be canceled. You need to set the clock first, then the
timer again.
FM
AM
DAB
TAPE
AUX
CD
FM
AM
DAB
Just Once
Every Day ( )
from Mon to Fri ( )
Continued
27-29_UX-HB4[B]6.p65 04.8.5, 6:17 PM28
29
Using Sleep Timer
With Sleep Timer, you can fall asleep to your favorite music
or radio program.
You can set Sleep Timer only when the unit is turned on.
You can also turn off the unit automatically by using Auto
Standby. (See page 10.)
How the Sleep Timer actually works
The unit automatically turns off after the specified length of
time passes.
On the remote control ONLY:
1
Press SLEEP.
The indicator starts flashing on the display.
Each time you press the button, the length of time
changes as follows:
2
Wait for about 5 seconds after specifying the
length of time.
The indicator flashes slowly on the display.
To check the remaining time until shut-off time, press
SLEEP once. The remaining time until shut-off time appears
for about 3 seconds.
To change the shut-off time, press SLEEP repeatedly until
the length of time you want appears.
To cancel the setting, press SLEEP repeatedly until the
SLEEP indicator goes off and display returns to the normal
indication.
Turning off the unit also cancels the Sleep Timer.
(canceled)
10 20
120
30 60
90
Off
SLEEP
When you set the Sleep Timer after the Daily Timer
starts playing the selected source
The unit turns off with either timer having an earlier shut-off time.
If you set the Sleep Timer while playing back or
recording a tape
Set the Sleep Timer not to shut the unit off while a tape is running.
If the unit turns off while playing back or recording a tape, the
cassette deck or tapes may be damaged.
27-29_UX-HB4[B]6.p65 04.8.5, 6:17 PM29
30
Maintenance
To get the best performance of the unit, keep your discs, tapes and mechanism clean.
General Notes
In general, you will have the best performance by keeping
your discs, tapes and the mechanism clean.
Store discs and tapes in their cases, and keep them in
cabinets or on shelves.
Cleaning the unit
Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
Since the unit may deteriorate in quality, become
damaged or have its paint peel off, be careful about the
following:
DO NOT wipe it with a rough cloth.
DO NOT wipe it too vigorously.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substance such as an
insecticide to it.
DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
Handling discs
Remove the disc from its case by
holding it at the edge while pressing
the center hole lightly.
Do not touch the shiny surface of the
disc, or bend the disc.
Put the disc back in its case after use
to prevent warping.
Be careful not to scratch the surface
of the disc when placing it back in
its case.
Avoid exposure to direct sunlight,
temperature extremes, and moisture.
To clean the disc
Wipe the disc with a soft cloth in a
straight line from center to edge.
DO NOT use any solventsuch as conventional
record cleaner, spray, thinner, or benzineto clean
the disc.
Handling cassette tapes
If the tape is loose in its cassette, take up the
slack by inserting a pencil in one of the reels
and rotating.
If the tape is loose, it may get stretched, cut,
or caught in the cassette.
Be careful not to touch the tape surface.
Avoid storing tapes in any of the following
places:
In dusty places
In direct sunlight or heat
In moist areas
On a TV or speaker
Near a magnet
To keep the best recording and playback sound quality
You need to clean the heads.
Clean the heads after every 10 hours of use with
a wet-type head cleaning tape (available at electronic and
audio shops).
When the head becomes dirty, the following symptoms will
occur:
Sound quality is reduced.
Sound level decreases.
Sound drops out.
Do not play dirty or dusty tapes.
Do not touch the highly-polished head with any metallic or
magnetic tools.
To demagnetize the head
Turn off the unit, and use a head demagnetizer (available at
electronic and audio shops).
Pinch Roller
Capstan
Head
30-32_UX-HB4[B]6.p65 04.8.5, 6:17 PM30
31
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,
such as your dealer for service.
Troubleshooting
Symptom
Power does not come on.
No sound is heard.
Hard to listen to broadcasts because of
noise.
The disc does not play.
Impossible to record.
Operations are disabled.
Unable to operate the unit by the remote
control.
Possible Cause
The power cord is not connected to an
AC outlet.
Connections are incorrect or loose.
A pair of headphones is connected.
MP3 disc is recorded with packet
writing.
Antennas are disconnected.
For AM (MW):
The AM (MW) loop antenna is too
close to the unit.
For DAB and FM:
The antenna is not properly extended
and positioned.
The disc is upside down.
Small tabs on the back of the cassette are
removed.
The built-in microprocessor has
malfunctioned due to external electrical
interference.
The path between the remote control
and the remote sensor on the unit is
blocked.
The batteries are exhausted.
You are using the remote control too
far from the unit.
Action
Insert the plug into the socket.
Check all connections and make
corrections. (See pages 6 to 8.)
Unplug the headphones from the
PHONES jack.
It cannot be played. Replace the disc.
Reconnect the antenna correctly and
securely.
Change the position and direction of
the AM (MW) loop antenna.
Extend antenna and orient to the best
reception position.
Put the disc in with the label side up.
Cover the holes with adhesive tape.
Unplug the AC power cord then plug it
back in.
Remove the obstruction.
Replace the batteries. (See page 8.)
Signals cannot reach the remote
sensor. Move closer to the unit.
30-32_UX-HB4[B]6.p65 04.8.5, 6:17 PM31
32
Amplifier Section
Output Power:
15 W per channel, min. RMS, driven into 4 at 1 kHz
with no more than 10% total harmonic distortion.
(IEC268-3)
Audio input sensitivity/Impedance (at 1 kHz)
AUX: 500 mV/50 k
Speakers Impedance: 4 16
Tuner
DAB tuning range: Band III
174.928 MHz 239.200 MHz
FM tuning range: 87.50 MHz 108.00 MHz
AM (MW) tuning range: 522 kHz 1 629 kHz
CD player
Dynamic range: 85 dB
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
Cassette deck
Frequency response:
Normal (type I): 100 Hz10 000 Hz
Wow and flutter: 0.35% (WRMS)
General
Power requirement: AC 230 V , 50 Hz
Power consumption: 40 W (at operation)
2 W (on standby)
Dimensions (W/H/D) (approx.):
152 mm x 233 mm x 297 mm
Mass (approx.): 4.0 kg
Supplied accessories
See page 6.
Speaker Section
Type: Full range, bass-reflex type
Speakers: 10 cm cone x1
Power handling capacity: 15 W
Impedance: 4
Frequency range: 100 Hz15 kHz
Dimensions (W/H/D) (approx.):
147 mm x 233 mm x 189 mm
Mass (approx.): 1.9 kg each
Specifications
Design and specifications are subject to change without notice.
30-32_UX-HB4[B]6.p65 04.8.5, 6:17 PM32
EN
0804AIMMDWORI
© 2004 Victor Company of Japan, Limited
UX-HB4
MICRO COMPONENT SYSTEM
UX-HB4[B]cover2.p65 04.8.5, 4:02 PM2
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC UXHB4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC UXHB4 in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info