Manual JVC UXH33 (page 3 of 32) (English)

29942

Zoom out

Zoom in

1/32

For Customer Use:

Enter below the Model No. and Serial No.

which are located either on the rear, bot-

tom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

UX-H35— Consists of CA-UXH35 and SP-UXH35

UX-H33— Consists of CA-UXH33 and SP-UXH33

UX-H30— Consists of CA-UXH30 and SP-UXH30

MICRO COMPONENT SYSTEM

INSTRUCTIONS

GVT0101-008A

[B]

MICRO COMPONENT SYSTEM

COVER_UX-H30[B]f.pm6 02.12.23, 10:04 PM1

G-1

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the

plug fitted is not suitable for the power points in your home

or the cable is too short to reach a power point, then

obtain an appropriate safety approved extension lead or

consult your dealer.

BE SURE to replace the fuse only with an identical

approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove

the fuse and dispose of the plug immediately, to avoid a

possible shock hazard by inadvertent connection to the

mains supply.

If this product is not supplied fitted with a mains plug then

follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured

in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed as

follows:

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

CAUTION— (standby/on) button!

Disconnect the mains plug to shut the power off completely

(all lamps and indications go off). The (standby/on)

button in any position does not disconnect the mains line.

• When the unit is on standby, the STANDBY lamp lights

red.

• When the unit is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

IMPORTANT FOR LASER PRODUCTS

REPRODUCTION OF LABELS

1 CLASSIFICATION LABEL ON EXTERIOR SURFACE

2 WARNING LABEL INSIDE THE UNIT

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when open and

interlock failed or defeated. Avoid direct exposure to

beam.

3. CAUTION: Do not open the top cover. There are no

user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

ADVARSEL: Usynlig laser-

stråling ved åbning, når

sikkerhedsafbrydere er ude

af funktion. Undgå udsæt-

telse for stråling (d)

VARNING: Osynlig laser-

strålning när denna del är

öppnad och spärren är

urkopplad. Betrakta ej

strålen. (s)

CAUTION: Invisible laser

radiation when open and

interlock failed or defeated.

AVOID DIRECT EXPOSURE

TO BEAM. (e)

VARO: Avattaessa ja suo-

jalukitus ohitettaessa olet

alttiina näkymättömälle

lasersäteilylle. Älä katso

säteeseen. (f)

CAUTION

• Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by

a newspaper or cloth, etc., the heat may not be

able to get out.)

• Do not place any naked flame sources, such as

lighted candles, on the apparatus.

• When discarding batteries, environmental

problems must be considered and local rules or

laws governing the disposal of these batteries must

be followed strictly.

• Do not expose this apparatus to rain, moisture,

dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the

apparatus.

SAFETY_UX-H30[B]f.pm6 02.12.23, 10:06 PM1

G-2

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured to meet international safety standards, but like any electrical equip-

ment, care must be taken if you are to obtain the best results and safety is to be assured.

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of

equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains

plug when making or changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way

—switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended

operation or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It

is illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the manufacturer’s

approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case—this

could result in a fatal electrical shock.

— NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!

✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮

Front View

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1 Front: No obstructions and open spacing.

2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3 Bottom: Place on a level surface. Maintain an adequate air path for ventilation by placing on a stand

with a height of 10 cm or more.

Side View

10 cm

15 cm

1 cm

15 cm

1 cm

15 cm

UX-H35/UX-H33/UX-H30

UX-H35

UX-H33

UX-H30

SAFETY_UX-H30[B]f.pm6 02.12.23, 10:06 PM2

Introduction

About This Manual

This manual is organized as follows:

• The manual mainly explains operations using the

buttons on the remote control.

You can use the buttons both on the remote

control and on the main unit for the same

operations if they have the same or similar names

(or marks), unless mentioned otherwise.

• Basic and common information that is the same for

many functions is grouped in one place, and is not

repeated for each procedure. For instance, we do not

repeat the information about turning on/off the unit,

setting the volume, changing the sound effects, and

others, which are explained in the section “Common

Operations” on pages 10 and 11.

• The following symbols are used in this manual:

Gives you warning and caution to

prevent damage or risk of fire/electric

shock.

Furthermore, it gives you information

about what is not good for obtaining

the best possible performance from the

unit.

Gives you information and hints you

should know.

Precautions

Installation

• Install in a place which is level, dry and neither too

hot nor too cold—between 5˚C and 35˚C.

• Install the unit in a location with adequate

ventilation to prevent internal heat buildup in the

unit.

• Leave sufficient distance between the unit and the

TV.

• Keep the speakers away from the TV to avoid

interference with TV.

DO NOT install the unit in a location near

heat sources, or in a place subject to direct

sunlight, excessive dust or vibration.

We would like to thank you for purchasing one of our JVC products.

Before operating this unit, read this manual carefully and thoroughly to obtain

the best possible performance from your unit, and retain this manual for future

reference.

Power sources

• When unplugging the unit from the wall outlet,

always pull on the plug, not the AC power cord.

DO NOT handle the AC power cord with

wet hands.

Moisture condensation

Moisture may condense on the lens inside the unit in

the following cases:

• After starting heating in the room

• In a damp room

• If the unit is brought directly from a cold to a warm

place

Should condensation occur, the unit may malfunction.

In this case, leave the unit turned on for a few hours

until the moisture evaporates, unplug the AC power

cord, then plug it in again.

Others

• Should any metallic object or liquid fall into the unit,

unplug the power cord and consult your dealer

before operating any further.

• If you are not going to operate the unit for an

extended period of time, unplug the power cord.

DO NOT disassemble the unit since there

are no user serviceable parts inside.

If anything goes wrong, unplug the power cord and

consult your dealer.

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:34 PM1

Contents

Location of the Buttons ............................................... 3

Main Unit .......................................................................... 3

Remote Control ................................................................. 5

Getting Started ............................................................. 6

Supplied Accessories ......................................................... 6

Connecting Antennas ........................................................ 6

Connecting Speakers ......................................................... 7

Connecting Other Equipment ............................................ 8

Putting the Batteries into the Remote Control .................. 9

Common Operations ................................................. 10

Setting the Clock ............................................................. 10

Turning On the Power ..................................................... 11

Adjusting the Volume ...................................................... 11

Adjusting the Tone (Bass/Treble) .................................... 11

Reinforcing the Bass Sound ............................................ 11

Listening to FM and AM (MW) Broadcasts ........... 12

Tuning in to a Station ...................................................... 12

Presetting Stations ........................................................... 12

Tuning in to a Preset Station ........................................... 13

Receiving FM Stations with RDS ................................... 13

Changing the RDS Information ...................................... 14

Searching for Programs by PTY Codes (PTY Search) ... 14

Switching Temporarily to a Program Type

of Your Choice .......................................................... 15

Playing Back Discs ..................................................... 16

Playing Back the Entire Disc—Normal Play .................. 16

Basic Disc Operations ..................................................... 17

Programming the Playing Order of the Tracks

—Program Play......................................................... 17

Playing at Random—Random Play ................................ 18

Repeating Tracks—Repeat Play ...................................... 18

Playing Back Tapes .................................................... 19

Playing Back a Tape ........................................................ 19

Recording ................................................................... 20

Recording on a Tape ........................................................ 20

Disc Direct Recording ..................................................... 21

One Track Recording ...................................................... 21

Using the Timers ........................................................ 22

Using Daily Timer and Recording Timer ........................ 22

Using Snooze Timer ........................................................ 24

Using Sleep Timer ........................................................... 24

Maintenance ............................................................... 25

Troubleshooting ......................................................... 26

Additional Information ............................................. 27

Specifications .............................................................. 28

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:34 PM2

MICRO COMPONENT SYSTEM

STANDBY

Top view

Front view

TIMER/SNOOZE

MULTI CONTROL

ONE TOUCH

REC

AHB PRO

VOLUME

AUX

TAPE CD

TUNER

BAND

COMPACT

DIGITAL AUDIO

PHONES

OPEN

Become familiar with the buttons on your unit.

Main Unit

Location of the Buttons

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM3

Main unit

1 PHONES jack (11)

2 Disc cover

3 TIMER/SNOOZE button (10, 22 – 24)

4 ONE TOUCH REC (recording) button (20, 21)

(standby/on) button (11, 23)

6 Source buttons

• AUX, @ # TAPE, BAND TUNER, and

#/8 CD

Pressing one of these buttons also turns on the

unit.

7 MULTI CONTROL buttons

• 4 (reverse skip), 7 (stop), and ¢ (forward

skip)

8 AHB (Active Hyper Bass) PRO button (11)

9 0 OPEN (disc cover open) button (16)

p VOLUME + / – buttons (11)

q Display window

w STANDBY lamp (11)

e Cassette holder

r Remote sensor

t ) (cassette holder open) button (19 – 21)

Display window

1 Tape operation indicators

• 2 3 (tape direction),

REC

(recording), and

(reverse mode)

(timer) indicator

3 REC (recording timer) indicator

4 ON/OFF (timer on-time/off-time) indicators

5 CLOCK indicator

BASS

indicator

SLEEP

indicator

SNOOZE

indicator

9 MONO and STEREO indicators

p RDS operation indicators

• RDS and TA /NEWS/INFO

q Main display

• Shows the source name, frequency, etc.

w Track calender indicators

e PROGRAM indicator

r RANDOM indicator

t Repeat indicators

•

and ALL

y OVER indicator

PROGRAM RANDOM ALL OVER

RDS TA NEWS INFO

MONOCLOCKOFF

REC ON

STEREO

BASS

REC

SLEEP SNOOZE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1234

yer

Display window

See the pages in parentheses for details.

Continued

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM4

Remote Control

See the pages in parentheses for details.

1 Number buttons

2 BASS button (11)

3 Multi control buttons

•

UP, 4 (reverse skip), 7 (stop), ¢

(forward skip), and

DOWN

4 SET button (13)

5 Source buttons

• 3/8 CD, 2 3 TAPE, TUNER, and AUX

Pressing one of these buttons also turns on the

unit.

6 REV.MODE (reverse mode) button (19 – 21)

7 PRGM (program) button (17)

8 RDS operation buttons (14, 15)

• PTY SEARCH, PTY SELECT + / –, DISPLAY,

and TA/NEWS/INFO

9 STANDBY/ON

button (11, 23)

p DISPLAY button (10)

q CLOCK/TIMER button (10, 22, 23)

w SLEEP button (24)

e TREBLE button (11)

r CANCEL button (18)

t AUTO PRESET button (12)

y FM MODE button (12)

u REPEAT button (18)

i RANDOM button (18)

o AHB (Active Hyper Bass) PRO button (11)

; VOLUME + / – button (11)

When using the remote control, point it at the

remote sensor on the front panel.

STANDBY/ON

DISPLAY

CLOCK

/TIMER

SLEEP

TREBLE

DOWN

BASS

CANCELSET

CD TAPE

TUNER AUX

REPEAT

PTY

SELECT

VOLUME

RANDOM

AHB PRO

DISPLAY

REV.MODE FM MODE

AUTO

PRESET

PRGM

TA/NEWS

/INFO

–

;

MICRO COMPONENT SYSTEM

STANDBY

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM5

Getting Started

Supplied Accessories

Make sure that you have all the following items.

The number in parentheses indicates the quantity of

each piece supplied.

• AM loop antenna (1)

• FM antenna (1)

• AC power cord (1)

• Remote control (1)

• Batteries (2)

If anything is missing, consult your dealer

immediately.

Connecting Antennas

FM antenna

1 Attach the FM antenna to the FM

COAXIAL 75 Ω terminal.

2 Extend the FM antenna.

3 Fasten it up in the position which gives

you the best reception, then fix it on the

wall, etc.

About the supplied FM antenna

The FM antenna supplied with this unit can be used as

temporary measure. If reception is poor, you can connect an

outdoor FM antenna.

FM antenna (supplied)

Outdoor FM antenna

(not supplied)

A 75 Ω antenna with coaxial type connector

(IEC or DIN 45325) should be used.

Coaxial cable (not supplied)

To connect an outdoor FM antenna

Before connecting the antenna, disconnect the supplied

FM antenna.

Continued

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM6

1 Connect the AM loop antenna to the

AM LOOP terminals as illustrated.

2 Turn the AM loop antenna until you

have the best reception.

To connect an outdoor AM (MW) antenna

When reception is poor, connect a single vinyl-covered

wire to the AM EXT terminal and extend it

horizontally. The AM loop antenna must remain

connected.

For better reception of both FM and AM (MW)

• Make sure the antenna conductors do not touch any other

terminals and connecting cords.

• Keep the antennas away from metallic parts of the unit,

connecting cords, and the power cord.

AM (MW) antenna

Vinyl-covered wire

(not supplied)

AM loop antenna

(supplied)

Connecting Speakers

1 Press and hold the clamp of the

speaker terminal on the rear of the

unit.

2 Insert the end of the speaker cord into

the terminal.

Match the polarity between the unit and the

speaker terminals: ª to ª and · to ·.

3 Release your finger from the clamp.

• DO NOT connect speakers while the

power is on.

• DO NOT connect more than one speaker

to each speaker teminal.

IMPORTANT: Use only speakers with the same

speaker impedance as shown on the speaker

terminals on the rear of the unit.

Speaker cord

Right speaker Left speaker

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM7

Speaker grille

To remove the speaker grille, insert your fingers at

the top of the speaker grille, pull towards you. Then

pull the bottom towards you.

To attach the speaker grille, follow the illustration

above.

Connecting Other Equipment

To connect an audio equipment

You can connect audio equipment—used only as a

playback device.

• DO NOT connect any equipment while

the power is on.

• DO NOT plug in any equipment until all

connections are complete.

Be sure that the plugs of the audio cords are colored:

White plugs and jacks are for left audio signals, and

red ones for right audio signals.

Holes

Projections

To remove the speaker grilles

The speaker grilles are removable.

To audio output

Audio equipment

NOW you are ready to plug in the unit

and any other connected equipment.

IMPORTANT: Be sure to check all connections to

be done before plugging the power cord.

This unit can be supplied with power through the AC

IN connector (at home) or the DC IN connector (in a

car).

• Do not connect the unit using the AC IN connector

and the DC IN connector at the same time for safe

and correct use.

To connect the AC power cord

Connect the AC power cord to the AC IN connector

and a wall outlet.

Continued

For playing other equipment through this unit,

connect between the audio output jacks on the other

equipment and AUX jacks by using audio cords (not

supplied).

AC IN

AC power cord (supplied)

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM8

Putting the Batteries into the Remote

Control

Insert the batteries—R6(SUM-3)/AA(15F)—into the

remote control, by matching the polarity (+ and –) on

the batteries with the + and – markings on the battery

compartment.

When the remote control can no longer operate the

unit, replace both batteries at the same time.

• DO NOT use an old battery together with

a new one.

• DO NOT use different types of batteries

together.

• DO NOT expose batteries to heat or

flame.

• DO NOT leave the batteries in the battery

compartment when you are not going to

use the remote control for an extended

period of time. Otherwise, the remote

control will be damaged from battery

leakage.

R6(SUM-3)/AA(15F)

12V 4A

DC IN

To car’s cigarette

lighter socket (12 V)

Car adapter

(JVC model: CA-R120E)

Connect a car adapter to the DC IN (12 V, 4 A)

connector and the cigarette lighter socket.

• DO NOT connect the car adapter to the

cigarette lighter socket before connecting

it to the DC IN connector. Otherwise, a

short-circuit may occur if the adapter plug

makes contact with any metal part inside

the car.

• DO NOT use this unit for a long time in a

car while the car ignition switch is turned

“OFF” (or set to “ACC”). Otherwise, the

car battery will be exhausted.

When using the unit in your car

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM9

Common Operations

Setting the Clock

Before operating the unit any further, first set the unit’s

clock. When you plug in the power cord, the CLOCK

indicator and “0:00” start flashing on the display.

You can set the clock whether the unit is on or off.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

On the remote control:

Press CLOCK/TIMER.

The hour digits start flashing on the

display.

Press UP or DOWN to

adjust the hour, then press

CLOCK/TIMER.

The minute digits start flashing.

Press UP or DOWN to adjust the

minute, then press CLOCK/TIMER.

On the unit:

Press TIMER/SNOOZE.

The hour digits start flashing on

the display.

Press ¢ or 4 to

adjust the hour, then

press TIMER/SNOOZE.

The minute digits start flashing.

CLOCK

/ TIMER

CLOCK

TIMER/SNOOZE

DISPLAY

Press ¢ or 4 to adjust the minute,

then press TIMER/SNOOZE.

To check the clock time during play

On the remote control ONLY:

Press DISPLAY (grey-colored).

• Each time you press the button, the

source indication and the clock time

alternate on the display.

• When you unplug the power cord or if a power failure

occurs

The clock is reset to “0:00” right away. If this happens, set

the clock again.

• The clock may gain or lose 1 to 2 minutes per month

If this happens, reset the clock.

To change the clock

1 Make sure the (timer) indicator is not lit on

the display.

• If it is lit, press and hold CLOCK/TIMER (or

TIMER/SNOOZE on the unit) until it goes off.

2 Press CLOCK/TIMER (or TIMER/SNOOZE

on the unit) repeatedly until the unit enters the

clock setting mode (the hour digits start flashing

on the display).

First time you press CLOCK/TIMER (or TIMER/

SNOOZE on the unit), the unit enters the timer

setting mode. (See page 22.)

3 Repeat steps

and

of the procedure of

“Setting the Clock.”

4 Press and hold CLOCK/TIMER (or TIMER/

SNOOZE on the unit) again so that the

(timer) indicator goes off.

DOWN

CLOCK

/ TIMER

TIMER/SNOOZE

Continued

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:35 PM10

Adjusting the Tone (Bass/Treble)

You can adjust the bass level (low frequency range)

and the treble level (high frequency range) within a

range of –5 to +5.

When shipped, the bass level set to “BASS 0” and the

treble level set to “TREBLE +1.”

• This function only affects the playback sound, and

does not affect your recording.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

On the remote control ONLY:

Press BASS to adjust the bass level or

press TREBLE to adjust the treble

level.

Press UP to increase the

level or press

DOWN to

decrease it.

Reinforcing the Bass Sound

You can reinforce the bass sound to maintain rich, full

bass at low volume—Active Hyper Bass Pro.

• This function only affects the playback sound, and

does not affect your recording.

To get the effect, press AHB PRO so

that the

BASS

indicator lights up on the

display.

• Each time you press the button, the

bass reinforcement alternates between on (AHB ON)

and off (AHB OFF).

To cancel the effect, press AHB PRO again so that the

BASS

indicator goes off.

Turning On the Power

To turn on the unit, press

STANDBY/ON

( on the unit).

The STANDBY lamp on the unit goes off.

• When you press the source button

—3/8 CD, 2 3 TAPE, TUNER (or

BAND TUNER on the unit) and AUX, the unit

automatically turns on and starts playback if the

source is ready.

To turn off the unit (standby), press

STANDBY/ON ( on the unit) again.

The STANDBY lamp on the unit lights on.

• The CLOCK indicator and “0:00” flash on the

display until you set the built-in clock. After setting

the clock, the clock time will appear on the display

while the unit is on standby.

• A little power is always consumed even while the

unit is on standby.

To switch off the power supply completely, unplug

the power cord.

When you unplug the power cord or if a power

failure occurs

The clock is reset to “0:00” right away, while the tuner preset

stations (see page 12) will be erased in a few days.

Adjusting the Volume

You can adjust the volume level only while the unit is

turned on. The volume level can be adjusted between

“VOL MIN” and “VOLUME 1” – “VOLUME 40

(VOL MAX).”

Press VOLUME + to increase the

volume or press VOLUME – to

decrease it.

For private listening

Connect headphones to the PHONES jack. No sound comes

out of the speakers. Be sure to turn down the volume before

connecting or putting on headphones.

DO NOT turn the unit off (standby) with the

volume set to an extremely high level;

otherwise, the sudden blast of sound can

damage your hearing, speakers and/or

headphones when you turn on the unit or

start playing any source next time.

REMEMBER you cannot adjust the volume

level while the unit is on standby.

VOLUME

BASS

TREBLE

DOWN

AHB PROAHB PRO

STANDBY/ON

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:36 PM11

Tuning in to a Station

Press TUNER (or BAND

TUNER on the unit) to select

the band.

The unit automatically turns on and

tunes in to the previously received

station—either FM or AM (MW).

• Each time you press the button, the

band alternates between FM and AM

(MW).

Press and hold ¢ or

4 for more than 1

second.

The unit starts searching for

stations and stops when a station of sufficient

signal strength is tuned in.

• If a program is broadcast in stereo, the

STEREO indicator lights up.

To stop searching, press ¢ or 4.

When you press ¢ or 4 briefly and

repeatedly

The frequency changes step by step.

To change the FM reception mode

On the remote control ONLY:

When an FM stereo broadcast is hard to

receive or noisy, press FM MODE so that

the MONO indicator lights up on the

display. Reception will improve.

To restore the stereo effect, press FM MODE again

so that the MONO indicator goes off. In stereo mode,

you can hear stereo sound when a stereo program is

broadcast.

Presetting Stations

You can preset 30 FM and 15 AM (MW) stations—

using either automatic presetting or manual presetting.

In some cases, test frequencies have been already

memorized for the tuner since the factory examined the

tuner preset function before shipment. This is not a

malfunction.

To preset stations automatically—Automatic

presetting

You need to preset stations separately for the FM and

AM (MW) bands.

On the remote control ONLY:

Press TUNER to select the

band.

The unit automatically turns on and

tunes in to the previously received

station—either FM or AM (MW).

• Each time you press the button, the band

alternates between FM and AM (MW).

Press and hold AUTO

PRESET for more than 2

seconds.

Local stations with strong signals are

searched for and stored in memory automatically.

When automatic presetting is over, the station

stored in preset number 1 is tuned in.

• Storing new stations erase the previously stored

one.

Repeat steps

and

to store stations

for the other band.

When you cannot automatically store stations

you want

Stations with weak signals cannot be detected with automatic

presetting. To store such stations, use manual presetting.

Listening to FM and AM (MW) Broadcasts

TUNER

BAND

FM MODE

AUTO

PRESET

AUTO

PRESET

TUNER

Continued

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:36 PM12

To preset stations manually—Manual presetting

You need to preset stations separately for the FM and

AM (MW) bands.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

On the remote control ONLY:

Tune in to the station you want to

preset.

• See “Tuning in to a Station” on page 12.

Press SET.

Press UP or DOWN

to select a preset number.

Press SET again.

The tuned station in step

is stored in the preset

number selected in step

• Storing a new station on a used number erases

the previously stored one.

When you unplug the power cord or if a power

failure occurs

The tuner preset stations will be erased in a few days. If this

happens, preset the stations again.

Tuning in to a Preset Station

On the remote control ONLY:

Press TUNER to select the

band.

The unit automatically turns on

and tunes in to the previously

received station—either FM or AM (MW).

• Each time you press the button, the band

alternates between FM and AM (MW).

Press UP or DOWN

to select a preset number.

DOWN

TUNER

DOWN

To tune in to a preset station directly using the

number buttons

On the remote control ONLY:

Pressing the number button(s)

allows you to select the preset

number you want.

Ex.: For preset number 5, press 5.

For preset number 15, press

+10, then 5.

For preset number 20, press

+10, then 10.

For preset number 30, press

+10, +10, then 10.

Receiving FM Stations with RDS

RDS (Radio Data System) allows FM stations to send

an additional signal along with their regular program

signals. For example, the stations send their station

names, as well as information about what type of

program they broadcast, such as sports or music, etc.

When tuned in to an FM station which provides the

RDS service, the RDS indicator lights up on the

display.

With the unit, you can receive the following types of

RDS signals.

PS (Program Service):

Shows commonly known station names.

PTY (Program Type):

Shows types of broadcast programs.

RT (Radio Text):

Shows text messages the station sends.

Enhanced Other Networks:

Provides information about the types of the

programs sent by other RDS stations.

More about RDS

• Some FM stations do not provide RDS signals.

• RDS services vary among FM RDS stations. For details on

RDS services in your area, check with local radio stations.

• RDS may not work correctly if the received station is not

transmitting the signals properly or if the signal strength is

weak.

SET

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:36 PM13

DISPLAY

(Program Service)

PTY

(Program Type)

(Radio Text)

Station frequency

(or preset channel no.)

Changing the RDS Information

You can see RDS information on the display while

listening to an FM station.

On the remote control ONLY:

Press DISPLAY (orange-colored).

• Each time you press the button, the

display changes to show the following

information:

• If no PS, PTY, or RT signals are sent by a station

“NO PS,” “NO PTY,” or “NO RT” appears on the display.

• On the characters displayed

When the display shows PS, PTY or RT signals:

– The display shows upper case letters only.

– The display cannot show accented letters; for example,

“A” may represent accented “A’s” like “Á, Â, Ã, À, Ä

and Å.”

Searching for Programs by PTY Codes

(PTY Search)

One of the advantages of RDS is that you can locate a

particular kind of program by specifying the PTY

codes.

• For details on the PTY codes, see “Additional

Information” on page 27.

To search for a program using the PTY codes

REMEMBER you must preset FM RDS stations to use

the PTY codes. If not yet done, see pages 12 and 13.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

PTY

On the remote control ONLY:

Press PTY SEARCH.

“PTY” and “SELECT” appear on the

display alternately.

Press PTY SELECT + or

PTY SELECT – until the

PTY code you want

appears on the display.

• Each time you press the buttons,

the PTY codes change as follows:

NONE Ô NEWS Ô AFFAIRS Ô

INFO Ô SPORT Ô EDUCATE Ô

DRAMA Ô CULTURE Ô SCIENCE Ô

VARIED Ô POP M Ô ROCK M Ô

EASY M Ô LIGHT M Ô CLASSICS Ô

OTHER M Ô WEATHER Ô

FINANCE Ô CHILDREN Ô SOCIAL Ô

RELIGION Ô PHONE IN Ô TRAVEL Ô

LEISURE Ô JAZZ Ô COUNTRY Ô

NATION M Ô OLDIES Ô FOLK M Ô

DOCUMENT Ô TEST Ô ALARM Ô

(back to the beginning)

Press PTY SEARCH once again.

While searching, “SEARCH” and the selected PTY

code alternately appear on the display.

The unit searches 30 preset FM stations, stops

when it finds the one you have selected (“FOUND”

and the selected PTY code appear), and tunes in

that station.

• If no program is found, “NOTFOUND” appears

on the display and the unit returns to the last

received station.

To stop searching any time during the process, press

PTY SEARCH while searching.

If you preset a station while PTY Search is

being carried out

PTY Search may not stop. If this happens, press PTY

SEARCH to stop searching manually.

PTY

SELECT

Continued

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:36 PM14

Switching Temporarily to a Program

Type of Your Choice

The Enhanced Other Networks function allows the unit

to switch temporarily to a broadcast program of your

choice (TA, NEWS, and INFO) from a different

station.

• The function only works when you are listening to a

preset FM RDS stations providing the data.

To activate the Enhanced Other Networks function

REMEMBER you must preset FM RDS stations to use

the function. If not yet done, see pages 12 and 13.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

On the remote control ONLY:

Press TA/NEWS/INFO until

the data type you want

appears on the display.

The selected data type indicator (TA,

NEWS, and INFO) also flashes.

• Each time you press the button, the data type

indicators change as follows:

TA : Traffic announcement

NEWS : News

INFO : Program the purpose of which is to

impart advice in the widest sense.

OFF : The function is canceled. The data

type indicator (TA, NEWS, and

INFO) goes off.

Wait for about 3 seconds after

specifying the data type.

The data type indicator stops flashing and remains

lit.

Now, the function is activated. See “How the

Enhanced Other Networks function actually

works.”

TA/NEWS

/INFO

TA NEWS INFO

OFF

(Canceled)

How the Enhanced Other Networks function

actually works:

CASE 1

If there is no station broadcasting the program

you have selected

The unit continues tuning in to the current station.

When a station starts broadcasting the program

you have selected, the unit automatically switches

to the station. The indicator of received PTY code

starts flashing.

When the program is over, the unit goes back to

the previously tuned station, but the function still

remains activated.

CASE 2

If there is a station broadcasting the program

you have selected

The unit tunes in to the program. The indicator of

received PTY code starts flashing.

When the program is over, the unit goes back to

the previously tuned station, but the function still

remains activated.

CASE 3

If the FM station you are listening to is

broadcasting the program you have selected

The unit continues to receive the station but the

indicator of received PTY code starts flashing.

When the program is over, the indicator of

received PTY code stops flashing and remains lit,

but the function still remains activated.

More about the Enhanced Other Networks

function

• The data sent from some stations may not be compatible

with this unit and also some stations may not include

Enhanced Other Networks data. In this case, the function

may not work correctly.

• While listening to a program tuned into by the function, the

station does not change even if another network station

starts broadcasting a program of the same data.

• The function is canceled when you change the source to

CD, TAPE or AUX, while it is temporarily canceled when

you change the source to AM (MW).

• This function is also canceled when you turn off the unit.

EN01-15_UX-H30[B]f.pm6 02.12.26, 1:37 PM15

Playing Back Discs

This unit has been designed to play back the following

discs—CD, CD-R, and CD-RW.

When playing a CD-R or CD-RW

User-edited CD-Rs (CD-Recordable) and CD-RWs

(CD-ReWritable) can be played only if they are

already “finalized.”

• Usually you can play back your original CD-Rs or

CD-RWs recorded in music CD format. However,

sometimes they may not play depending on their

characteristics or recording conditions.

• Before playing CD-Rs or CD-RWs, read their

instructions or cautions carefully.

• Some CD-Rs or CD-RWs may not play on this unit

because of their disc characteristics, damage or stain

on them, or if the player’s lens is dirty.

• CD-RWs may require a longer readout time. This is

because the reflectance of CD-RWs is lower than for

regular discs.

General notes

In general, you will have the best performance by

keeping your discs and the mechanism clean.

• Store discs in their cases, and keep them in cabinets

or on shelves.

• Keep the unit’s disc cover closed when

not in use.

Continued use of irregular shape discs

(heart-shape, octagonal, etc.) can damage

the unit.

Playing Back the Entire Disc—Normal Play

Press 0 OPEN on the unit.

The disc cover opens.

• You can insert a disc while

listening to another source.

Place a disc correctly with its label side

up.

Close the disc cover gently.

Press 3/8 CD.

The unit automatically turns on and the

first track of the disc starts playing.

• The track number that has already played

disappears from the track calender on the

display.

• The disc automatically stops when the last track

has finished playing.

To stop playing, press 7.

To remove the disc, press 0 OPEN on the unit.

• If the disc cannot be read correctly (because it is

scratched, for example) or an unreadable CD-R or CD-

RW is inserted

Playback will not start.

• If no disc is inserted

“NO DISC” appears on the display.

• If the loaded disc has more than 15 tracks

The OVER indicator lights on the display.

DO NOT try to open the disc cover by hand

as it will be damaged.

CORRECT INCORRECT

OPEN

OVER

REC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Total track number Total playing time

OVER

REC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Track number Elapsed playing time

Continued

EN16-19_UX-H30[B]f.pm6 02.12.26, 1:37 PM16

Basic Disc Operations

While playing a disc, you can do the following

operations.

To stop playing for a moment

During play, press 3/8 CD.

While pausing, the elapsed playing time

flashes on the display.

To resume playing, press 3/8 CD again.

To go to another track

Before or during play, press ¢ or

4 repeatedly.

• ¢ : Skips to the beginning of the

next or succeeding tracks.

• 4 : Goes back to the beginning of

the current or previous tracks.

To go to another track directly using the number

buttons

On the remote control ONLY:

Pressing the number button(s)

before or during play allows you

to start playing the track number

you want.

Ex.: For track number 5, press 5.

For track number 15, press

+10, then 5.

For track number 20, press

+10, then 10.

For track number 32, press

+10, +10, +10, then 2.

To locate a particular point in a track

During play, press and hold ¢ or

• ¢ : Fast-forwards the tracks.

• 4 : Fast-reverses the tracks.

Programming the Playing Order of the

Tracks—Program Play

You can arrange the order in which tracks play before

you start playing. You can program up to 20 tracks.

On the remote control ONLY:

Load a disc.

• If the current playing source is not the CD

player, press 3/8 CD, then 7 before going to

the next step.

Press PRGM (program).

The PROGRAM indicator lights up

on the display.

• If a program has been stored in memory, the

program is called up.

Press UP or DOWN

to select the track number,

then press SET.

• You can select the track number

directly using the number

button(s). (See “To go to another

track directly using the number

buttons.”)

Repeat step

to program

other tracks you want.

Press 3/8 CD.

The tracks are played in the order you have

programed.

If you try to program a 21st track

“FULL” will appear on the display.

To stop playing, press 7.

To exit from Program Play, press

PRGM (program) before or after playing.

• The PROGRAM indicator goes off.

PRGM

PROGRAM

Track number Program step number

PRGM

DOWN

SET

EN16-19_UX-H30[B]f.pm6 02.12.26, 1:37 PM17

To skip the current track, press ¢.

• You cannot go back to the previous

track by pressing 4.

To stop playing, press 7.

To exit from Random Play, press

RANDOM before or after playing.

Random Play is canceled and Normal Play

resumes.

• The RANDOM indicator goes off.

Repeating Tracks—Repeat Play

You can have all the tracks, the program or individual

track currently playing, repeat as many times as you

like.

On the remote control ONLY:

To repeat playing, press REPEAT before

or during play.

• Each time you press the button, Repeat

Play changes as follows, and the

following repeat indicator lights up on the display:

: Repeats one track.

ALL : In Normal Play, repeats all the tracks.

In Program Play, repeats all the tracks in

the program.

In Random Play, repeats all the tracks in

random order.

To cancel Repeat Play, press REPEAT repeatedly

until the repeat indicator goes off.

• Repeat Play remains in effect even when you select

another play mode (Normal, Program or Random

Play).

• In Random Play,

cannot be selected. If has

been selected when you press RANDOM, it is

canceled.

To check the program contents

You can check the program

contents by pressing ¢ or 4

before or after playback.

• ¢ : To check the contents in

the programmed order.

• 4 : To check the contents in the reverse order.

To modify the program

On the remote control ONLY:

Before or after playing, you can erase the

last programed track by pressing CANCEL.

• Each time you press the button, the last

programed track is erased from the

program.

To add tracks in the program before playing, simply

select the track numbers you want to add by following

step

of the programming procedure.

To erase the program, press 7 before or

after playing.

• Pressing 0 OPEN to open the disc cover

will also erase the programed tracks.

Playing at Random—Random Play

The tracks will play in no particular order when you

use this mode.

On the remote control ONLY:

Load a disc.

• If the current playing source is not the CD

player, press 3/8 CD, then 7 before going to

the next step.

Press RANDOM.

The RANDOM indicator lights up on

the display.

Press 3/8 CD.

The tracks are randomly played.

Random Play ends when all the tracks

are played once.

CANCEL

RANDOM

REPEAT

Canceled

ALL

RANDOM

EN16-19_UX-H30[B]f.pm6 02.12.26, 1:37 PM18

Playing Back Tapes

You can play back type I tapes.

Playing Back a Tape

Press ) for cassette deck on the unit.

The cassette holder opens.

Put a cassette in with the exposed part

of the tape down.

Close the cassette holder cover gently.

Press 2 3 TAPE.

The unit automatically turns on and

the tape starts playing. The tape

direction indicator (3 or 2) flashes

slowly on the display.

• Each time you press the button, the tape

direction changes:

3 : plays the front side.

2 : plays the reverse side.

When the tape plays to the end, the deck

automatically stops if the Reverse Mode is set to

or . (See “To play both sides—Reverse

Mode.”)

If no cassette is inserted when you press

2 3 TAPE

“NO TAPE” appears on the display.

To stop playing, press 7.

To fast-wind to the left or to the

right, press ¢ or 4 while the

tape is not running.

The tape direction indicator (3 or 2)

starts flashing rapidly on the display.

To remove the cassette, press ) on

the unit.

To play both sides—Reverse Mode

You can set the deck to play just one side of a tape,

both sides once, or both sides continuously.

On the remote control ONLY:

Press REV.MODE (reverse mode).

• Each time you press the button, the

Reverse Mode changes as follows:

: The deck automatically stops after playing

both sides of the tape. Stops when playback

in the 2 direction is finished.

: The deck continues to play both sides of the

tape until 7 is pressed.

: The deck automatically stops after playing

one side of the tape.

The use of C-120 or thinner tape is not

recommended, since characteristic

deterioration may occur and this tape easily

jams in the pinch-rollers and the capstans.

REV.MODE

TAPE

EN16-19_UX-H30[B]f.pm6 02.12.26, 1:37 PM19

Recording

Close the cassette holder gently and

check the recording direction for the

tape.

• If the tape direction is not correct, press 2 3

TAPE twice then 7 to change the tape direction.

• If you want to record on both sides of a tape, see

“To record on both sides—Reverse Mode.”

Start playing the source—FM, AM

(MW) or auxiliary equipment

connected to AUX jacks.

• When the source is the CD player, see “Disc

Direct Recording” on page 21.

Press ONE TOUCH

REC (recording).

The

REC

(recording) indicator

lights up on the display and recording starts.

• If no cassette is inserted when you press REC

“NO REC” appears on the display.

• If a protected tape is inserted when you press REC

“NO REC” appears on the display.

To stop while recording, press 7.

To remove the cassette, press ) on the

unit.

To record on both sides—Reverse Mode

On the remote control ONLY:

Press REV.MODE (reverse mode)

repeatedly until

or is lit.

• When using the Reverse Mode for

recording,

lights up and start

recording in the forward (3) direction first.

Otherwise, recording will stop when recording is

done only on one side (reverse) of the tape.

IMPORTANT:

• It should be noted that it may be unlawful to re-

record pre-recorded tapes, records, or discs

without the consent of the owner of copyright in

the sound or video recording, broadcast or cable

program and in any literary, dramatic, musical,

or artistic embodied therein.

• The recording level is automatically set correctly, so

it is not affected by the other sound settings. Thus,

during recording you can adjust the sound you are

actually listening to without affecting the recording

level.

• If recordings you have made have excessive noise or

static, the unit may be too close to a TV. Increase the

distance between the TV and the unit.

• You can use type I tape for recording.

To protect your recording

Cassettes have two

small tabs on the

back to protect from

unexpected erasure

or re-recording.

To protect your recording, remove these tabs.

To re-record on a protected tape, cover the holes with

adhesive tape.

At the start and end of cassette tapes

There is leader tape which cannot be recorded onto. Thus,

when recording discs or radio broadcasts, wind the leader tape

first to ensure that the recording will be made without any

loss.

Recording on a Tape

On the unit ONLY:

Put a recordable cassette in with the

exposed part of the tape down.

ONE TOUCH

REC

REV.MODE

Continued

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:38 PM20

Disc Direct Recording

Everything on the disc goes onto the tape in the order it

is on the disc, or according to the order you have set in

Program Play.

On the unit ONLY:

Put a recordable cassette in with the

exposed part of the tape down.

Load a disc.

• If the current playing source is not the CD

player, press 3/8 CD, then 7 before going to

the next step.

— If you do not want pauses of about 4 seconds

recorded between selections, press 3/8 CD

twice. Otherwise, a non-recorded pause will

be automatically inserted between selections.

• If you want to record on both sides of a tape, see

“To record on both sides—Reverse Mode.”

Press ONE TOUCH

REC (recording).

The

REC

(recording) indicator

lights up on the display and recording starts.

After recording, the CD player and cassette deck

automatically stop.

To stop while recording, press 7.

The tape stops after 4 seconds.

To remove the cassette, press ) on the

unit.

To record on both sides—Reverse Mode

On the remote control ONLY:

Press REV.MODE (reverse mode)

repeatedly until

or is lit.

• When using the Reverse Mode for Disc

Direct Recording,

lights up and start

recording in the forward (3) direction first. When

the tape reaches its end while recording a song in the

forward direction (3), the last song will be re-

recorded at the beginning of the reverse side (2).

If you start recording on the reverse side (2),

recording will stop when recording is done only on

one side (reverse) of the tape.

When making Sleep Timer settings while doing

Disc Direct Recording

Set enough time to allow for the disc to finish playing;

otherwise, the power will go off before recording is

completed.

One Track Recording

This recording method is convenient when you record

tracks while playing the disc. You can record just your

favorite songs on the tape.

On the unit ONLY:

Put a recordable cassette in with the

exposed part of the tape down.

Play the track on the disc you wish to

record.

Press ONE TOUCH

REC (recording).

The CD player returns to the

beginning of that track and the track is recorded on

the tape.

After recording, the CD player and cassette deck

automatically stop.

Repeat steps

and

to record other

tracks you want.

To stop while recording, press 7.

The tape stops after 4 seconds.

To remove the cassette, press ) on the

unit.

ONE TOUCH

REC

REV.MODE

ONE TOUCH

REC

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:38 PM21

Using the Timers

There are four timers available—Daily Timer,

Recording Timer, Snooze Timer, and Sleep Timer.

Before using the timers, you need to set the unit’s

clock (see page 10).

Using Daily Timer and Recording Timer

You can set the timer whether the unit is on or off.

How the timer actually works

When the on-time comes, the unit automatically turns

on (the

[timer] indicator flashes just before the on-

time and continues flashing while the timer is

operating). Then, when the off-time comes, the unit

automatically turns off (standby).

The timer setting remains in memory until you change

it.

• When the

(timer) indicator is lit on the display,

the timer acts as the Daily Timer. Once the timer has

been set, it will be activated at the same time

everyday until the timer is turned off.

• When the

(timer) and the REC indicators are lit

on the display, the timer acts as the Recording Timer.

After the timer-recording finishes, the details of the

setting remain stored but the timer is turned off.

Before you start...

When using “

TUNER” as the source to play, make

sure to select the desired station before turning off the

power.

• There is a time limit in doing the following steps. If

the setting is canceled before you finish, start over

from step

Press CLOCK/TIMER

(or TIMER/SNOOZE on

the unit).

The (timer) and the ON

indicators light up and the

current on-time flashes on the

display.

The unit enters on-time setting mode.

Set the on-time when you want the unit

to turn on.

On the remote control:

1) Press

UP or DOWN to set

the hour, then press

CLOCK/TIMER.

2) Press

UP or DOWN to set

the minute, then press

CLOCK/TIMER.

On the unit:

1) Press ¢ or 4 to set the

hour, then press TIMER/

SNOOZE.

2) Press ¢ or 4 to set the

minute, then press

TIMER/SNOOZE.

The OFF indicator lights up and the unit enters

off-time setting mode.

Set the off-time when you want the unit

to turn off (standby).

On the remote control:

1) Press

UP or DOWN to set the hour, then

press CLOCK/TIMER.

2) Press UP or DOWN to set the minute,

then press CLOCK/TIMER.

On the unit:

1) Press ¢ or 4 to set the hour, then press

TIMER/SNOOZE.

2) Press ¢ or 4 to set the minute, then press

TIMER/SNOOZE.

The unit enters the timer selecting mode.

OFF

DOWN

CLOCK

/ TIMER

TIMER/SNOOZE

Continued

CLOCK

/ TIMER

TIMER/SNOOZE

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:38 PM22

Select the timer (Daily

Timer or Recording Timer)

with the source to play.

On the remote control:

Press

UP or DOWN to

select the timer, then press

CLOCK/TIMER.

On the unit:

Press ¢ or 4 to select the

timer, then press TIMER/SNOOZE.

• Each time you press

(¢) or

DOWN (4), the

timer mode and the source

change as follows:

TUNER : tunes in to the last station you were

listening to. (Daily Timer)

REC

TUNER : records the last station you were

listening to. (Recording Timer)

• Put a recordable cassette into the deck.

CD : plays a disc. (Daily Timer)

• Load a disc.

TAPE : plays a tape. (Daily Timer)

• Make sure that the tape is in the cassette

deck.

• Make sure that the tape direction is

correct.

The unit enters the volume level setting mode.

Select the volume level.

On the remote control:

Press

UP or DOWN to set the volume level,

then press CLOCK/TIMER.

On the unit:

Press ¢ or 4 to set the volume level, then

press TIMER/SNOOZE.

• You can select the volume level

(“VOLUME – –” and “VOLUME 0” to

“VOLUME 40”).

If you select “VOLUME – –,” the volume is set

to the previous level when the unit was turned

off.

• To turn off the volume while the Recording

Timer (

REC

TUNER) is working, set the volume

level “VOLUME 0.”

The unit enters the clock setting mode.

TUNER TUNER

REC

CDTAPE

Adjust the clock if you need.

• See “Setting the Clock” on page 10.

Press STANDBY/ON

(or on the unit) to turn

off the unit (standby) if you

have set the timer with the

unit turned on.

• When the timer turns on the unit, the (timer)

indicator starts flashing. (If the Recording Timer

is selected in step

, the REC indicator also

starts flashing.)

To deactivate the timer temporarily,

press and hold CLOCK/TIMER (or

TIMER/SNOOZE on the unit) until

the

(timer) indicator on the display

goes off.

To activate or change the timer

(with the previous setting), follow

steps

on pages 22 and 23.

• If you want to change the timer setting after the

Daily Timer be used, first deactivate the timer.

• If the unit is turned on when the timer on-time comes

Timer does not work.

• When you unplug the power cord or if a power failure

occurs

The timer will be canceled. You need to set the clock first,

then the timer again.

STANDBY/ON

DOWN

CLOCK

/ TIMER

TIMER/SNOOZE

CLOCK

/ TIMER

TIMER/SNOOZE

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:38 PM23

Using Sleep Timer

With the Sleep Timer, you can fall asleep to music. You

can set the Sleep Timer when the unit is turned on.

How the Sleep Timer actually works

The unit automatically turns off after the specified time

length passes.

On the remote control ONLY:

Press SLEEP.

The time length until the shut-off time

appears and the

SLEEP

indicator lights

up on the display.

• Each time you press the button, the time length

changes as follows:

Wait for about 5 seconds after

specifying the time length.

To check the remaining time until the shut-off time,

press SLEEP once so that the remaining time until the

shut-off time appears for about 5 seconds.

To change the shut-off time, press SLEEP repeatedly

until the desired time length appears on the display.

To cancel the setting, press SLEEP repeatedly until

the

SLEEP

indicator goes off.

• The Sleep Timer is also canceled when you turn off

the unit.

• If you set the Sleep Timer after the Daily Timer starts

playing the selected source

The Daily Timer is canceled. When the Sleep Timer shut-

off time comes, the unit will be turned off.

• If you set the Sleep Timer after the Recording Timer

starts recording

The Recording Timer is canceled, but recording continues

until the Sleep Timer shuts off the power.

SLEEP 10

Canceled

SLEEP 20 SLEEP 30

SLEEP 60

SLEEP 90SLEEP120

SLEEP

Using Snooze Timer

The Snooze Timer turns off the unit (standby) only for

5 minutes while the Daily Timer is in operation.

• You can set the Snooze Timer only while the Daily

Timer is in operation.

Press TIMER/SNOOZE on

the unit (or CLOCK/TIMER

on the remote control) while

the Daily Timer is in operation.

The unit turns off (standby) and the

SNOOZE

indicator lights up on the display.

After 5 minutes, the unit automatically

turns on.

• If the unit is turned on when the Snooze Timer is

working

The Snooze Timer and the Daily Timer will be canceled.

• If you set the Snooze Timer when there is less than 5

minutes until the Daily Timer off-time

The unit will not turn on even when 5 minutes passed.

• When you unplug the power cord or if a power failure

occurs

The timer will be canceled. You need to set the clock first,

then the timer again.

TIMER/SNOOZE

CLOCK

/ TIMER

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:39 PM24

Maintenance

To get the best performance from the unit, keep your discs, tapes, and mechanism clean.

Handling cassette tapes

• If the tape is loose in its cassette,

take up the slack by inserting a

pencil in one of the reels and

rotating.

• If the tape is loose, it may get

stretched, cut, or caught in the

cassette.

• Be careful not to touch the tape

surface.

• Avoid storing tapes in the following

places:

—In dusty places

—In direct sunlight or heat

—In moist areas

—On a TV or speaker

—Near a magnet

To keep the best recording and playback sound

quality

If the heads, capstans, and pinch rollers of the cassette

deck become dirty, the following will occur:

• Impaired sound quality

• Discontinuous sound

• Fading

• Incomplete erasure

• Difficulty in recording

To clean the heads, capstans, and pinch rollers

Use a cotton swab moistened with alcohol.

To demagnetize the heads

Turn off the unit, and use a head demagnetizer

(available at electronics and audio shops).

Cleaning the unit

• Stains on the unit

Should be wiped off with a soft cloth. If the unit is

heavily stained, wipe it with a cloth soaked in water-

diluted neutral detergent and wrung well, then wipe

clean with a dry cloth.

• Since the unit may deteriorate in quality, become

damaged or have its paint peel, be careful about

the following.

—DO NOT wipe it with a rough cloth.

—DO NOT wipe it strongly.

—DO NOT wipe it with thinner or benzine.

—DO NOT apply any volatile substances such as

insecticides to it.

—DO NOT allow any rubber or plastic to remain in

contact with it for a long time.

Handling discs

• Remove the disc from its case by

holding it at the edge while

pressing the center hole lightly.

• Do not touch the shiny surface of

the disc, or bend the disc.

• Put the disc back in its case after

use to prevent warping.

• Be careful not to scratch the

surface of the disc when

placing it back in its case.

• Avoid exposure to direct

sunlight, temperature extremes,

and moisture.

To clean the disc

Wipe the disc with a soft cloth

in a straight line from center to

edge.

DO NOT use any solvent—such as conventional

record cleaner, spray, thinner, or benzine—to clean

the disc.

Heads

Capstans

Pinch Rollers

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:39 PM25

Troubleshooting

If you are having a problem with your unit, check this list for a possible solution before calling for service.

If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified

person, such as your dealer, for service.

Symptom

No sound is heard.

Hard to listen to broadcasts because

of noise.

The disc does not play.

The disc sound is discontinuous.

The cassette holder cannot be

opened.

Impossible to record.

Operations are disabled.

Unable to operate the unit from the

remote control.

Cause

• Connections are incorrect or

loose.

• Headphones are connected.

• Antennas are disconnected.

• The AM loop antenna is too close

to the unit.

• The FM antenna is not properly

extended and positioned.

The disc is placed upside down.

The disc is scratched or dirty.

Power from the power cord has been

cut off while the tape was running.

Small tabs on the back of the

cassette are removed.

The built-in microprocessor may

malfunction due to external

electrical interference.

• The path between the remote

control and the remote sensor on

the unit is blocked.

• The batteries are exhausted.

Action

• Check all connections and make

corrections. (See pages 6 – 9.)

• Disconnect the headphones.

• Reconnect the antennas correctly

and securely.

• Change the position and direction

of the AM loop antenna.

• Extend the FM antenna to the best

position.

Place the disc with the label side up.

Clean or replace the disc. (See page

25.)

Plug in the power cord, then turn on

the unit.

Cover the holes with adhesive tape.

Unplug the power cord and then

plug it back in.

• Remove the obstruction.

• Replace the batteries.

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:39 PM26

Additional Information

NEWS: News.

AFFAIRS: Topical program expanding or enlarging

upon the news—debate, or analysis.

INFO: Program the purpose of which is to impart

advice in the widest sense.

SPORT: Program concerned with any aspect of

sports.

EDUCATE: Educational programs.

DRAMA: All radio plays and serials.

CULTURE: Programs concerning any aspect of national

or regional culture, including language,

theater, etc.

SCIENCE: Programs about natural sciences and

technology.

VARIED: Used for mainly speech-based programs

such as quizzes, panel games and

personality interviews.

POP M: Commercial music of current popular

appeal.

ROCK M: Rock music.

EASY M: Current contemporary music considered to

be “easy-listening.”

LIGHT M: Instrumental music, and vocal or choral

works.

CLASSICS: Performances of major orchestral works,

symphonies, chamber music, etc.

OTHER M: Music not fitting into any of the other

categories.

WEATHER: Weather reports and forecasts.

FINANCE: Stock Market reports, commerce, trading

etc.

CHILDREN: Programs targeted at a young audience.

SOCIAL: Programs about sociology, history,

geography, psychology and society.

RELIGION: Religious programs.

PHONE IN: Involving members of the public expressing

their views either by phone or at a public

forum.

TRAVEL: Travel information.

LEISURE: Programs about recreational activities.

JAZZ: Jazz music.

COUNTRY: Songs which originate from, or continue the

musical tradition of the American Southern

States.

Description of the PTY codes:

Alarm function

If an “ALARM” (Emergency) signal is received

from a station while listening to the radio, the unit

automatically switches to the station broadcasting

the “ALARM” signal, except when you are

listening to non-RDS stations—all AM (MW) and

some FM stations.

Test function

The “TEST” signal is used for testing the

“ALARM” signal.

Therefore, it makes the unit work in the same way

as the “ALARM” signal does.

If a “TEST” signal is received from a station while

listening to the radio, the unit automatically

switches to the station broadcasting the “TEST”

signal, except when you are listening to non-RDS

stations—all AM (MW) and some FM stations.

Classification of the PTY codes for some FM

stations may be different from the above list on

this page.

NATION M: Current popular music of the nation or

region in that country’s language.

OLDIES: Music from the so-called “golden age” of

popular music.

FOLK M: Music which has its roots in the musical

culture of a particular nation.

DOCUMENT: Program concerning factual matters,

presented in an investigative style.

TEST: Broadcasts for testing emergency broadcast

equipment or receiver.

ALARM: Emergency announcement.

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:39 PM27

Specifications

Amplifier

Output Power:

20 W (10 W + 10 W) at 4 Ω (10% THD)

Audio input sensitivity/Impedance (at 1 kHz)

AUX: 500 mV/48.75 kΩ

Speakers/Impedance: 4 Ω

Tuner

FM tuning range: 87.50 MHz – 108.00 MHz

AM tuning range:

MW: 522 kHz – 1 629 kHz

CD player

Dynamic range: 85 dB

Signal-to-noise ratio: 90 dB

Wow and flutter: Immeasurable

Cassette deck

Frequency response:

Normal (type I): 50 Hz – 15 000 Hz

Wow and flutter: 0.15% (WRMS)

Speaker

Speaker units:

Full range: 8.0 cm cone x 1

Impedance: 4 Ω

Dimensions (approx.):

135 mm x 203 mm x 190 mm (W/H/D)

Mass (approx.): 1.7 kg each

Supplied Accessories

See page 6.

General

Power requirement:

AC IN: 230 V

, 50 Hz

DC IN: 12 V, 4 A

Power consumption: 35 W (at operation)

3.0 W (on standby)

Dimensions (approx.):

412 mm x 208 mm x 275 mm (W/H/D)

Mass (approx.): 6.5 kg

Design and specifications are subject to change

without notice.

EN20-28_UX-H30[B]f.pm6 02.12.26, 1:39 PM28

VICTOR COMPANY OF JAPAN, LIMITED

EN 0103MWMMDWJEM

COVER_UX-H30[B]f.pm6 02.12.23, 10:04 PM2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JVC UXH33 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JVC UXH33 Manual

Product: