614784
16
Zoom out
Zoom in
Previous page
1/20
Next page
G-2
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment, care must be taken
if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are
properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connec-
tions.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw the
mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch
television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s approved stand or
legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal electrical
shock.;
— NEVER guess or take chances with electrical equipment of any kind
— it is better to be safe than sorry!
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
UX-T550(B)_Safety.pm6 12/12/00, 3:12 PM2
1
Thank you for purchasing this JVC product. Please read these instructions carefully before starting operation to be sure to obtain optimum
performance and a longer service life from the unit.
CONTENTS
Features ..................................................................... 1
Handling precautions ............................................... 1
Connections .............................................................. 2
Power supply ............................................................. 4
Names of parts and their functions......................... 5
Remote control unit .................................................. 6
Switching the power on/off ...................................... 6
Volume, tone and other controls ............................. 7
Handling CDs............................................................. 7
Playing CDs ............................................................... 8
Handling cassette tapes ......................................... 10
Cassette playback ................................................... 10
Radio reception ....................................................... 11
Recording ................................................................ 12
Clock adjustment .................................................... 13
Timer operations ..................................................... 14
Maintenance ............................................................ 16
Troubleshooting ...................................................... 16
Specifications............................................ Back page
FEATURES
CD-size micro component system consisting of 3 units
Active Hyper-Bass PRO circuit for low-frequency sound reproduction
One-touch operation (COMPU PLAY)
35-key remote control unit operates all CD, cassette deck and tuner
functions
Multi-function CD player
Programmed play of up to 20 tracks
Repeat Play
Random Play
U-Turn auto-reverse full-logic mechanism
Auto tape select mechanism
Metal (type IV) and CrO2 (type II) tape can be played back for supe-
rior tone quality
CrO2 (type II) tape recording capability
2-band digital synthesizer tuner with 45-station (30 FM and 15 AM
(MW/LW)) preset capability
Seek/manual tuning
Auto preset tuning
Timer/Clock function
Timer on/off with preset volume function
Sleep timer can be set for up to 120 minutes
HANDLING PRECAUTIONS
1. Avoid installing in the following places
Where it could be subject to vibrations.
Where it is excessively humid, such as in a bathroom.
Where it could be magnetized by a magnet or speaker.
2. Pay attention to dust
Be sure to close the CD holder or CD tray so that dust does not
collect on the lens.
3. Condensation
In the following cases, condensation may occur in the unit, in which
case the unit may not operate correctly.
In a room where a heater has just been switched on.
In a place where there is smoke or high humidity.
When the unit is moved directly from a cold to a warm room.
In these cases, set the button to STANDBY and wait 1 or 2
hours before use.
4. Volume setting
CDs produce very little noise compared with analog sources. If the
volume level is adjusted for these sources, the speakers may be
damaged by the sudden increase of output level. Therefore, lower
the volume before operation and adjust it as required during play.
Do not use this unit in direct sunlight where it would be exposed to high temperatures above 40°C (104°F).
5. Safety mechanism
This unit incorporates a safety interlock mechanism which switches
the laser beam on and off, so that when the CD holder or CD tray is
open, the laser beam stops automatically.
6. Do not place cassette tapes, etc. near the speakers
Since there are magnets in the speakers, do not place tapes or mag-
netic cards on them as recorded data could be erased.
7. Keep this unit away from your TV
When this unit is used near a TV, the TV picture could be distorted.
If this happens, move this unit away from the TV. If this does not
correct the situation, avoid using this unit when the TV is turned on.
8. Cleaning the cabinet
If the cabinet gets dirty, wipe it with a soft, dry cloth. Never use
benzine or thinner as these could damage the surface finish.
9. When listening with headphones
Do not listen at high volumes as this could damage your hearing.
For safety, do not drive while listening to this unit.
UX-T550(B)_body.pm6 12/12/00, 3:11 PM1
2
CONNECTIONS
Do not switch the power on until all connections are completed.
Antenna connection and adjustment
AM (MW/LW) loop antenna adjustment
Keep the loop antenna away from the unit and install it so that the best reception is obtained. (Do not leave the antenna wire in a bundle.)
ÓAC IN
RIGHT
R
L
LEFT
DC IN
12V
FM
AM LOOP
AM EXT
COAXIAL
75
Insert in the direction of the arrow.
AM (MW/LW)loop antenna (provided)
ÓAC IN
RIGHT
R
L
LEFT
DC IN
12V
FM antenna connections and adjustments
FM wire antenna (provided)
FM outdoor antenna (option)
Coaxial cable
Notes:
Do not place the loop antenna on a metal desk or near a TV or per-
sonal computer.
Installing an outdoor antenna requires expertise; we recommend that
you consult an audio dealer.
Install the antenna cord away from the power and speaker cords as
these could generate noise. Do not install the loop antenna so that it
touches the rear of the unit.
Use an outdoor antenna when stable reception cannot be obtained with the provided antenna.
UX-T550(B)_body.pm6 12/12/00, 3:11 PM2
3
Attaching the speaker grille
Notes:
The polarity of the two connected speakers will be the same if the
black speaker cords are connected to the · terminals. If the speak-
ers are connected with polarities reversed, stereo effect and tone will
be degraded.
The speakers of this unit are not magnetically shielded. When they
are placed directly on or adjacent to a TV, the TV’s picture could be
distorted. Install the speakers more than 20 cm away from your TV.
When connecting the speaker cord make sure that the wire core, not
the insulating cover, is connected to the speaker terminal. Otherwise,
sound cannot be heard.
The speaker grilles can be removed.
When removing.
1. Insert your fingers at the top and pull towards you.
2. Also pull the bottom towards you.
Speaker cord connection
Connec the cord from the speaker on
the left to the (LEFT) terminal and the
cord from the speaker on the right to
the (RIGHT) terminals.
Match the fittings when
attaching the grille.
Speaker grille
ÓAC IN
R
L
DC IN
12V
1
23
RIGHT
LEFT
RIGHT
LEFT
Connect the black cord to the · terminal.
Right speaker (rear side)
Left speaker (rear side)
Speaker cord
Black
ÓAC IN
DC IN
12V
R
L
AUX
RIGHT
R
L
LEFT
Connection of external audio units
Connection with a turntable (or MD player)
Note:
Regarding the connection with external units and their operations,
refer to the instructions provided with those units.
Pin-plug x 2
Pin-plug x 2
Signal cord (optional)
Turntable (with built-in equalizer) or MD
player (optional)
UX-T550(B)_body.pm6 12/12/00, 3:11 PM3
4
POWER SUPPLY
A. Connection of AC power cord
Connect the AC power cord after all other connections have been made.
CAUTIONS:
1.ONLY USE WITH JVC POWER CORD PROVIDED WITH THIS
UNIT TO AVOID MALFUNCTION OR DAMAGE TO THE UNIT.
2.BE SURE TO UNPLUG THE POWER CORD FROM THE OUT-
LET WHEN GOING OUT OR WHEN THE UNIT IS NOT IN USE
FOR AN EXTENDED PERIOD OF TIME.
First connect the car adapter to the DC IN 12 V jack, not the cigarette
lighter socket, because shorting of a plug on the car may cause the
fuse to blow out. In addition, be careful not to make a short-circuit
between the plugs.
When using a car battery, be sure to use the specified car adapter
(JVC model CA-R120E) to prevent mishaps or damage resulting
from different polarity design.
B. Operation on car battery (DC 12 V)
Note:
When there is a power failure or the AC power cord is disconnected,
the timer/clock setting is erased from memory. Reset the clock when
the power supply is restored.
ÓAC IN
RIGHT
R
L
LEFT
12V
DC IN
DC IN
12V
To car’s cigarette lighter socket (12 V)
~
Ÿ
Optional exclusive car adapter (JVC model CA-R120E)
DC IN
12V
RIGHT
R
L
LEFT
ÓAC IN
ÓAC IN
Power cord
UX-T550(B)_body.pm6 12/12/00, 3:11 PM4
6
REMOTE CONTROL UNIT
Preparation before use
Installing batteries in the remote control unit
1. Remove the battery cover from the back of the remote control unit.
2. Insert two “R6/AA (15F)” size batteries.
Insert the batteries with the ª and · terminals matching the
indication inside the battery compartment.
3. Replace the cover.
The following operations can be performed using the remote control unit.
Check the operation button functions carefully and operate them correctly.
~ Track number buttons (No. 1 to No. 10. +10)
Pres station buttons (No. 1 to No. 10. +10)
Ÿ REVERSE MODE button
: For signal-side recording or playback.
: For recording or playback on both sides.
: For continuous play.
! BEAT CUT button
PROGRAM button
@ BASS buttons (+, –)
(Control range from -6 to 6.)
¤ TREBLE buttons (+. –)
(Control range from -6 to 6.)
# button.
SLEEP button
$ DISPLAY button
Use to display the current time.
STEREO AUTO/MONO button
% AUTO PRESET botton
REPEAT button
^ RANDOM button
Buttons not mentioned here have the same functions as those
on the main unit.
Battery replacement
When the remote control operation becomes unstable or the distance
from which remote control is possible decreases, replace the batter-
ies.
Using the remote control unit
Point at the remote sensor and operate within about 7 m (approx. 23
ft).
The remote control range is less when the unit is used at an angle.
Do not expose the remote sensor to strong direct sunlight or artificial
lighting.
Make sure that there are no obstacles between the remote sensor
and the unit.
SWITCHING THE POWER ON/OFF
Switching the power on/off
Switching on:
Switching off:
STANDBY
STANDBY
The STANDBY indicator goes out.
The indicator in the display window lights.
The STANDBY indicator lights.
The indicator in the display window goes out and
only the clock is indicated.
BAND
ONE TOUCH
REC
TAPE
OPEN
CD
TUNER
TIMER/SNOOZE
STANDBY
AUX
MICRO COMPONENT SYSTEM UX-T550
VOLUME
M
U
L
T
I
J
O
G
ACTIVE HYPER
BASS PRO
CLOCK
TUNER/BAND button
CD Play/pause (#8) button
TAPE
play (2, 3) buttons
AUX button
button
Insert the · ends first.
SLEEP
12
3
4
7
10
8
+10
AUX
9
6
5
AUTO
PRESET
DISPLAY
PROGRAM RANDOM
REPEATBEAT CUT
REVERSE
MODE
STEREO
AUTO/MONO
MULTI CONTROL
BASS
AHB PRO
TREBLE
REW
FF
VOLUME
RM-RXUT100
REMOTE CONTROL
TAPE TUNER
BAND
C D
~
Ÿ
!
@
¤
#
$
%
^
UX-T550(B)_body.pm6 12/12/00, 3:11 PM6
13
CLOCK ADJUSTMENT
Names of parts in the clock/timer section, and their functions:
~ Timer mode indicator
Ÿ Timer indicator (ON/OFF)
! CLOCK indicator
SLEEP indicator
@ Time display
¤ CLOCK button
# TIMER/SNOOZE button
MULTI JOG dial
It is used to set the current time and perform timer setting.
BEAT CUT button (using the remote control unit)
When recording an AM broadcast, beats may be produced which are
not heard when listening to the broadcast. In such case, set this button
after setting the deck to the record mode so that the beats are elimi-
nated. Normally set this button to “CUT-1”.
Erasing
A recorded tape can be erased by recording new material over the pre-
vious material.
To erase a tape without making a new recording...
1. Press the TAPE (23) button to set to the TAPE mode.
2. Press the 7 button.
3. Insert the cassette with the side to be erased facing out.
4. Press the ONE TOUCH REC button.
It should be noted that it may be unlawful to re-record pre-recorded
tapes, records, or discs without the consent of the owner of copy-
right in the sound or video recording, broadcast or cable programme
and in any literary, dramatic, musical, or artistic work embodied
therein.
BEAT CUT
Setting the current time (when this unit is used for the first time)
(Example: To set the clock to 13:15.)
1 Connect the AC power cord; “CLOCK” will blink in the display.
2 Press the CLOCK button for 2 seconds or more.
3 Set to 13: 15 using the MULTI JOG Dial and CLOCK button.
Setting the current time.
Use the time signal of television and radio broadcasts.
When adjusting the clock, follow steps 23.
Notes:
Before performing timer recording or playback, it is necessary to set
the current time.
It is recommended to set the current time with the button set to
STANDBY so that the current display mode is maintained.
When the power cord is plugged in again after being disconnected or
power is restored after a power failure, “CLOCK” will blink in the dis-
play. Set the current time again.
SLEEP
CLOCK
REC
OFF
ON
COMPACT
DIGITAL AUDIO
BAND
ONE TOUCH
REC
TAPE
OPEN
CD
TUNER
TIMER/SNOOZE
M
U
L
T
I
J
O
G
ACTIVE HYPER
BASS PRO
CLOCK
~
¤
#
Ÿ
!⁄@
CLOCK
M
U
L
T
I
J
O
G
CLOCK
CLOCK
M
U
L
T
I
J
O
G
CLOCK
CLOCK
CLOCK
CLOCK
CLOCK
CLOCK
1
2
3
Within the 2 minutes.
Back
Advance
One hour is advanced/moved back every 2 clicks.
One minute is advanced/moved back every 2 clicks.
UX-T550(B)_body.pm6 12/12/00, 3:11 PM13
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC UX-T550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC UX-T550 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info