Manual JVC RX-6042S (page 15 of 44) (English)

602844

Zoom out

Zoom in

1/44

Listening with headphones:

You can enjoy not only stereo software but also multi-

channel software through the headphones. (Sounds are

down-mixed to the front channels while playing multi-channel

software.)

1 Press SPEAKERS ON/OFF to deactivate the speakers.

“HEADPHONE” appears for a while, and the H.PHONE

indicator lights on the display.

• If the Surround or DSP mode has been activated, “3D H

PHONE” appears for a while (and the DSP indicator also lights

up on the display)—3D Headphone Mode (3D H PHONE). For

details, see page 26.

2 Connect the headphones to the PHONES jack on the front

panel.

• If you do not deactivate the speakers, no sound comes out of

the headphones.

After using the headphones, disconnect the headphones, then press

SPEAKERS ON/OFF again to activate the speakers.

CAUTION:

Be sure to turn down the volume....

• Before connecting or putting on headphones, as its high

volume can damage both the headphones and your hearing.

• Before turning on speakers again, as its high volume may

come out of the speakers.

Turning On and Off the

Subwoofer Sound

You can cancel the subwoofer output even though you have

connected a subwoofer and have set “SUBWOOFER” to

“SUBWOOFER YES” (see page 20).

Press SUBWOOFER OUT ON/OFF to cancel the subwoofer

output.

Each time you press the button, subwoofer output is deactivated

(“SUBWOOFER OFF”) and activated (“SUBWOOFER ON”)

alternately.

• When subwoofer output is canceled, the

indicator goes off.

Bass sounds (and LFE signals) will be emitted through the front

speakers.

Notes:

• When subwoofer output is activated, you can also adjust the

subwoofer output level. For details, see page 24.

• You cannot deactivate the subwoofer output when you set “SMALL”

for the front speakers on the speaker size setting (see page 20) or

using Quick Speaker Setup (see page 18).

• You cannot activate the subwoofer output when you have set

“SUBWOOFER” to “SUBWOOFER NO” (see page 20).

• When you change the “SUBWOOFER” setting from “SUBWOOFER

NO” to “SUBWOOFER YES” (see page 20), subwoofer output is

automatically activated.

Selecting the Analog or Digital Input Mode

When you have connected digital source components using the both

analog and digital terminals (see pages 7 to 10), you can select the

input mode—either digital or analog—for these components.

Before you start, remember...

The digital input terminal setting should be correctly done for

the sources you want to select the digital input mode (see

“Setting the Digital Input Terminals” on page 22).

1 Press one of the source selection buttons (DVD, TV

SOUND, CD, TAPE/CDR*) for which you want to

change the input mode.

If “TAPE” is selected as the source, digital input mode is not

available. To change the source name, see “Changing the

Source Name” on page 14.

2 Press INPUT DIGITAL to select “DIGITAL AUTO.”

The DIGITAL AUTO indicator lights up on the display.

• When using the remote control, press ANALOG/DIGITAL.

Each time you press the button, the analog (ANALOG) and

digital (DIGITAL AUTO) input modes alternate.

• When selecting “DIGITAL AUTO,” the following indicators

indicate the digital signal format of the incoming signal.

: Lights up when Linear PCM signals come

in.

: Lights up when Dolby Digital signals

come in.

: Lights up when conventional DTS signals

come in.

: Lights up when DTS 96/24 signals come

in.

No indicator lights up when the receiver cannot recognize the

digital signal format of the incoming signals.

Note:

For details about the digital signal formats, see pages 25 and 26.

Continued on the next page

Remote

NOT

Remote

NOT

11-15_5040&6040[J]f.p65 03.12.20, 14:2813

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JVC RX-6042S in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC RX-6042S

JVC RX-6042S User Manual - German, Dutch, French - 126 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JVC RX-6042S Manual

Product: