602848
26
Zoom out
Zoom in
Previous page
1/39
Next page
23
English
4. Adjust the speaker output levels.
To adjust the center speaker level, press
CENTER –/+ (from –10 dB to +10 dB).
To adjust the left rear speaker level, press
REAR•L –/+ (from –10 dB to +10 dB).
To adjust the right rear speaker level, press
REAR•R –/+ (from –10 dB to +10 dB).
5. Press TEST again to stop the test
tone.
JVC Theater Surround adjustments
Before you start, remember...
Make sure that you have set the speaker information correctly
(see page 12).
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
You cannot adjust the rear speaker output levels when you have set
“REAR SPK” to “NONE. See page 12.
You cannot adjust the center speaker output level and center tone
when you have set “CENTER SPK” to “NONE.” See page 12.
From the remote control:
1. Press SURROUND MODE
repeatedly until “THEATER”
appears on the display.
The Ÿ PRO LOGIC and DSP indicators
also light up on the display.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker
output balance.
“TEST TONE L” starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
Notes:
You can adjust the speaker output levels without outputting the
test tone.
No test tone comes out of the center speaker when “CENTER
SPK” is set to “NONE” (see page 12).
No test tone comes out of the rear speakers when “REAR SPK”
is set to “NONE” (see page 12).
+10
10
– REAR•R +
ENTER
MENU
98
– REAR•L +
6
5
– CENTER +
1
TEST
TEST TONE L
(Left front speaker)
TEST TONE LS
(Left rear speaker)
TEST TONE RS
(Right rear speaker)
TEST TONE C
(Center speaker)
TEST TONE R
(Right front speaker)
SURROUND
SURROUND
MODE
SOUND
1
TEST
SURROUND
On the front panel:
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make adjustments while listening to
the sound of the source played back.
1. Press SURROUND to active an
appropriate Surround mode —
PRO LOGIC, DOLBY DIGITAL
or DTS SURROUND.
Each time you press the button, the Surround mode turns on
and off alternately.
When “PRO LOGIC” is selected, the Ÿ PRO LOGIC
indicator lights up on the display.
2. Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
Once you have pressed ADJUST,
MULTI CURSOR % / can be also
used for selecting the speaker.
2) Press MULTI CURSOR @ / # to
adjust the selected speaker output level
(from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
MULTI CURSOR
ADJUST
EN18_25.RX-6000V[J] 99.12.16, 1:10 PM23
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC RX-6000VBK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC RX-6000VBK in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info