602848
15
Zoom out
Zoom in
Previous page
1/39
Next page
12
English
Setting the Speakers for the DSP Modes
To obtain the best possible surround sound of the DSP (Digital
Signal Processor) modes (see page 18), you have to register the
information about the speakers arrangement after all connections are
completed.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
On the front panel ONLY:
1. Press SETTING repeatedly until
“FRONT SPK” (Front Speaker),
“CENTER SPK” (Center
Speaker), or “REAR SPK” (Rear
Speaker) appears on the display.
Once you have pressed SETTING, MULTI
CURSOR % / can be also used for
selecting the speakers.
2. Press MULTI CURSOR @ / # to
select the appropriate item about
the speaker selected in the above
step.
LARGE: Select this when the speaker size is relatively large.
SMALL: Select this when the speaker size is relatively small.
NONE: Select this when you have not connected a speaker.
(Not selectable for the front speakers)
3. Repeat steps 1 and 2 to select the appropriate
items for the other speakers.
Notes:
Keep the following comment in mind as reference when adjusting.
If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LARGE, and if it is smaller than 12 cm,
select “SMALL.
If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
If you have selected “SMALL” for the front speaker setting, you
cannnot select “LARGE” for the center and rear speaker settings.
When you change your speakers, you need to register the
information about the speaker again.
SETTING
MULTI CURSOR
MULTI CURSOR
SETTING
LARGE
SMALL NONE
MULTI CURSOR
Center Delay Time Setting
Register the delay time of the sound from the center speaker,
comparing that of the sound from the front speakers.
If the distance from your listening point to the center speaker is
equal to that to the front speakers, select 0 msec. As the distance to
the center speaker becomes shorter, increase the delay time.
1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
When shipped from the factory, delay time is set to 0 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CENTER DELAY” appears on
the display.
Once you have pressed SETTING, MULTI CURSOR % /
can be also used for selecting “CENTER DELAY.
The display changes to show the current setting.
2. Press MULTI CURSOR @ / # to
select the delay time of the center
speaker output.
Pressing # increases the delay time from
0 msec (“C. DELAY: 0ms”) to 5 msec (“C.
DELAY: 5ms”).
Pressing @ decreases the delay time from
5 msec (“C. DELAY: 5ms”) to 0 msec (“C.
DELAY: 0ms”).
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers,
comparing that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal
to that to the front speakers, select 0 msec. As the distance to the rear
speakers becomes shorter, increase the delay time.
1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
Rear delay time for Dolby Digital and DTS Digital Surround is to
be set to 5 msec.
When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“REAR DELAY” appears on the
display.
Once you have pressed SETTING, MULTI CURSOR % /
can be also used for selecting “REAR DELAY.
The display changes to show the current setting.
2. Press MULTI CURSOR @ / # to
select the delay time of the rear
speaker output.
Pressing # increases the delay time from
0 msec (“R. DELAY: 0ms”) to 15 msec
(“R. DELAY: 15ms”).
Pressing @ decreases the delay time from
15 msec (“R. DELAY: 15ms”) to 0 msec
(“R. DELAY: 0ms”).
SETTING
EN08_17.RX-6000V[J] 99.12.14, 4:42 PM12
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC RX-6000VBK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC RX-6000VBK in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info