57258
35
Zoom out
Zoom in
Previous page
1/71
Next page
33
English
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s
service center.
SOLUTION
Plug the power cord into an AC outlet.
Check speaker wiring and reconnect if necessary.
(See page 5.)
Press SPEAKERS ON/OFF so that the sounds
come out of the speakers. (See page 11.)
Select the correct source.
Press MUTING to cancel the mute. (See page 13.)
Select the correct input mode (analog or digital).
(See pages 11 and 12.)
If subwoofer is connected, set “SUBWOOFER
YES” so that the SUBWOOFER OUT ON/OFF
button works.
Connect an outdoor FM antenna or contact your
dealer. (See page 4.)
Select a new station.
Check with your dealer to be sure you have the
correct antenna.
Check connections. (See pages 4 and 5.)
Move the antenna farther from automobile traffic.
1. Press STANDBY/ON
on the front panel to
turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Press STANDBY/ON
on the front panel to turn
off the receiver, then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug the
AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact your
dealer.
Press STANDBY/ON on the front panel to turn
off the receiver. After unplugging the AC power
cord, contact your dealer.
Press STANDBY/ON
on the front panel to turn
off the receiver. After unplugging the AC power
cord, contact your dealer.
Remove the obstruction.
Replace batteries. (See page 4.)
Select the correct remote control operation mode.
(See pages 29 to 32.)
POSSIBLE CAUSE
The power cord is not plugged in.
Speaker signal cables are not
connected.
The SPEAKERS ON/OFF button is
not set correctly.
An incorrect source is selected.
Muting is activated.
An incorrect input mode (analog or
digital) is selected.
The SUBWOOFER OUT ON/OFF
button is pressed while
“SUBWOOFER” is set to
“SUBWOOFER NO.”
Incoming signal is too weak.
The station is too far away.
An incorrect antenna is used.
Antennas are not connected properly.
Ignition noise from automobiles.
Speakers are overloaded because of
high volume.
Speakers are overloaded because of
short circuit of speaker terminals.
The built-in microcomputer is not
functioning correctly.
The receiver is overloaded because of
a high voltage.
There is an obstruction between the
remote sensor on the receiver and the
remote control.
Batteries are weak.
An incorrect remote control operation
mode is selected.
PROBLEM
The display does not light up.
No sound from speakers.
“NO SUBWOOFER” appears on the
display.
Continuous hiss or buzzing during FM
reception.
Noise is heard during FM/AM
reception.
“OVERLOAD” starts flashing on the
display.
“DSP NG” appears on the display.
The STANDBY lamp lights up after
turning on the power, and soon the
receiver turns off again (into standby
mode).
Remote control does not work.
Remote control does not work as you
intend.
28-34_RX-5060B[C].p65 05.12.24, 12:3333
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC RX-5060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC RX-5060 in the language / languages: English, French as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC RX-5060

JVC RX-5060 User Manual - German - 71 pages

JVC RX-5060 User Manual - Dutch - 71 pages

JVC RX-5060 User Manual - French - 71 pages

JVC RX-5060 User Manual - Italian - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info