663480
32
Zoom out
Zoom in
Previous page
1/96
Next page
28
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
INSTALLATION / CONNECTION
Warning
The unit can only be used with a 12V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
Insulate unconnected wires with vinyl tape to prevent a short circuit.
Be sure to ground this unit to the car’s chassis again after installation.
Caution
For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
Do not connect the
wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
Connect speakers with a maximum power of more than 50W. If the
maximum power of the speakers is lower than 50W, change the
[AMP GAIN]
setting to avoid damaging the speakers.
(
18)
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
Keep all cables away from heat dissipate metal parts.
After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then
disconnect the
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection.
(
29
,
30)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Press to turn on the power.
6 Reset the unit within 5 seconds.
(
3)
Do the required wiring.
(
29
,
30
)
Dashboard of your car
Bend the appropriate tabs to hold
the mounting sleeve firmly in place.
Installing the unit (in-dash mounting)
When installing without the
mounting sleeve
1 Remove the mounting sleeve and
trim plate from the unit.
2 Align the holes in the unit (on
both sides) with the vehicle
mounting bracket and secure the
unit with screws (supplied).
How to remove the unit
1
Fit the catch pin on the
extraction keys into the holes on
both sides of the trim plate, then
pull it out.
2 Insert the extraction keys deeply
into the slots on each side, then
follow the arrows as shown
below.
Use only the specified screws. Using wrong
screws might damage the unit.
JS_JVC_KW_R920BT_DB92BT_E_EN_1.indd 28JS_JVC_KW_R920BT_DB92BT_E_EN_1.indd 28 3/11/2015 9:00:07 AM3/11/2015 9:00:07 AM
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC KW-R920BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC KW-R920BT in the language / languages: English, German, French as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info