165014
27
Zoom out
Zoom in
Previous page
1/28
Next page
GET0013-001A
[E]
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
ENGLISH
DEUTSCH
FRANÇAIS
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende
handleiding.
COMPACT
DIGITAL AUDIO
KD-S811R/KD-S713R/
KD-S711R
NEDERLANDS
KD-S811R
KD-S713R
KD-S711R
COVER.KD-S811R[E].001A/5 07/12/2000, 05:05 PM3
2
ENGLISH
Position And Reproduction Of Labels
DANGER: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgåudsæt-
telse for stråling. (d)
VARNING: Osynlig laser-
strålning när denna del
är öppnad och spärren
är
urkopplad. Betrakta
ej
strålen. (s)
VARO : Avattaessa ja suo-
jalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
Caution:
This product contains a laser component
of higher laser class than Class 1.
IMPORTANT FOR LASER PRODUCTS
Precautions:
1.CLASS 1 LASER PRODUCT
2.DANGER: Invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to
beam.
3.CAUTION: Do not open the top cover. There are no
user-serviceable parts inside. Leave all servicing to
qualified service personnel.
4.CAUTION: This CD player uses invisible laser
radiation and is equipped with safety switches to
prevent radiation emission when unloading CDs. It is
dangerous to defeat the safety switches.
5.CAUTION: Use of controls, adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Name/Rating plate
Bottom panel of the main unit
How to reset your unit
Press and hold both the SEL (select) and (standby/on/attenuator) buttons at the same
time for several seconds.
This will reset the built-in microcomputer.
Notes:
Your preset adjustments — such as preset channels or sound adjustments — will also be erased.
If a CD is in the unit, it will eject when you reset the unit. Pay attention not to drop the CD.
SEL (Select)
(Standby/On/Attenuator)
EN02-03.KD-S811/713/711R[E]12 07/12/2000, 05:12 PM2
3
ENGLISH
BEFORE USE
*
For safety....
Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
Stop the car before performing any complicated
operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the units chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.
CONTENTS
How to reset your unit ............................... 2
LOCATION OF THE BUTTONS............ 4
Control panel ............................................ 4
BASIC OPERATIONS ...................... 5
Turning on the power ................................ 5
RADIO BASIC OPERATIONS ............. 6
Listening to the radio ................................ 6
Storing stations in memory ....................... 7
Tuning into a preset station....................... 8
RDS OPERATIONS ........................ 9
What you can do with RDS EON.............. 9
Other convenient RDS functions and
adjustments ........................................... 12
CD OPERATIONS .......................... 14
Playing a CD ............................................ 14
Locating a track or a particular portion on a
CD ......................................................... 15
Selecting CD playback modes.................. 15
Prohibiting CD ejection ............................. 16
SOUND ADJUSTMENTS .................. 17
Adjusting the sound ................................. 17
Using the
Sound Control Memory (SCM) .............. 17
Storing your own sound adjustments ....... 18
OTHER MAIN FUNCTIONS ............... 19
Setting the clock ...................................... 19
Changing the general settings (PSM) ...... 19
Detaching the control panel...................... 22
REMOTE CONTROLLER .................. 23
(With an optionally purchased remote
controller) (only for KD-S811R)
Installing the battery ................................. 23
Using the remote controller ...................... 24
TROUBLESHOOTING...................... 25
MAINTENANCE ............................ 26
Handling CDs .......................................... 26
SPECIFICATIONS .......................... 27
EN02-03.KD-S811/713/711R[E]12 07/12/2000, 05:12 PM3
ENGLISH
4
LOCATION OF THE BUTTONS
Control panel
1 (standby/on/attenuator) button
2 Control dial
3 DISP (display) button
4 AM button
5 CD button
6 FM button
7 0 (eject) button
8 4
/¢ buttons
Also functions as SSM buttons when pressed
together.
9 SEL (select) button
p Remote sensor (only for KD-S811R)
q MO (monaural) button
RND (random) button
w Number buttons
e TP (traffic programme)
RDS (radio data system) button
r PTY (programme type) button
t SCM (sound control memory) button
y
(control panel release) button
;
a
s
u
oi
Display window
Display window
u Volume (or audio) level indicator
Equalization Pattern indicator
i Tuner reception indicators
STEREO, MONO
o RND (random) indicator
; RDS indicators
AF, EON, REG, TP, PTY
a “SCM” indicator
s LOUD indicator
d Sound mode indicators
BEAT, SOFT, POP
f CD indicator
g Band indicators
FM1, FM2, FM3
AM
h Main display
j CD IN indicator
d
treq9
p
yw
23
54
67 8
1
fh
j
g
EN04-04.KD-S811/713/711R[E]15 07/12/2000, 05:11 PM4
5
ENGLISH
BASIC OPERATIONS
4
Adjust the sound as you want (see
page 17.)
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
If you rotate the control dial clockwise, you can
also restore the sound.
To turn off the power
Press and hold for more than 1 second.
Note:
When you use this unit for the first time, set the built-in
clock correctly, see page 19.
CAUTION on Volume Setting
CDs produce very little noise compared with other
sources. If the volume level is adjusted for the tuner,
for example, the speakers may be damaged by the
sudden increase in the output level. Therefore, lower
the volume before playing a disc and adjust it as
required during playback.
To increase the volume.
1
32
Volume level appears.
Volume level indicator
To decrease the volume.
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
When you select a source in step 2 below, the power
automatically comes on. You do not have to press
this button to turn on the power.
2
Select the source.
To operate the tuner (AM or FM),
see pages 6 13.
To operate the CD player,
see pages 14 16.
3
Adjust the volume.
EN05-05.KD-S811/713/711R[E]13 07/12/2000, 05:10 PM5
6
ENGLISH
RADIO BASIC OPERATIONS
To stop searching before a station is received,
press the same button you have pressed for
searching.
Searching a station manually:
Manual search
1
Select the band (AM, FM1 – 3).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Press and hold ¢ or 4 until
"M"(manual) starts flashing on the
display.
Listening to the radio
You can use either automatic searching or manual
searching to tune into a particular station.
Searching a station automatically:
Auto search
1
Select the band (AM, FM1 3).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Start searching a station.
When a station is received, searching
stops.
Press ¢
to search
stations of higher
frequencies.
Press 4
to search
stations of lower
frequencies.
FM1
FM2 FM3
Selected band appears.
FM1
FM2 FM3
AM
Selected band appears.
Audio (see page 21) or volume level
indicator
AM
EN06-08.KD-S811/713/711R[E]14 07/12/2000, 05:15 PM6
7
ENGLISH
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).
1
Select the FM band (FM1 3) you want
to store FM stations into.
Each time you press the button, the FM
band changes as follows:
2
Press and hold both buttons for more
than 2 seconds.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3.)
These stations are preset in the number buttons —
No.1 (lowest frequency) to No.6 (highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
Lights up when receiving an
FM broadcast in stereo.
3
Tune into a station you want while M
is flashing.
If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.
If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for FM
and 9 kHz intervals for AM MW/LW) until
you release the button.
When an FM stereo broadcast is hard to
receive:
Press MO RND (monaural/random) while listening
to an FM stereo broadcast.
Each time you press the button, the MO indicator
lights up and goes off alternately.
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator goes
off).
Press ¢ to search
stations of higher
frequencies.
Press 4
to search
stations of lower
frequencies.
FM1
FM2 FM3
SSM appears, then disappears when automatic
preset is over.
EN06-08.KD-S811/713/711R[E]14 07/12/2000, 05:15 PM7
8
ENGLISH
Manual preset
You can preset up to 6 stations in each band (FM1,
FM2, FM3 and AM) manually.
Ex: Storing an FM station of 88.3 MHz into the
preset number 1 of the FM1 band
1
Select the FM band (FM1 3) you
want to store FM stations into (in
this example, FM1).
Each time you press the button, the FM
band changes as follows:
2
Tune into a station of 88.3 MHz.
3
Press and hold the number button (in
this example, 1) for more than 2
seconds.
4
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
A previously preset station is erased when a new station
is stored in the same preset number.
Preset stations are erased when the power supply to the
memory circuit is interrupted (for example, during
battery replacement). If this occurs, preset the stations
again.
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If you
have not stored them yet, see Storing stations in
memory on page 7.
1
Select the band (AM, FM1 3).
2
Select the number (1 6) for the preset
station you want.
Press ¢ to tune in
stations of higher
frequencies.
Press 4
to tune in
stations of lower
frequencies.
FM1
FM2 FM3
P1 flashes for a few
seconds.
FM1
FM2 FM3
AM
EN06-08.KD-S811/713/711R[E]14 07/12/2000, 05:15 PM8
9
ENGLISH
RDS OPERATIONS
What you can do with RDS EON
RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations send
their station names, as well as information about
what type of programme they broadcast, such as
sports or music, etc.
Another advantage of RDS function is called “EON
(Enhanced Other Networks).The EON indicator
lights up while receiving an FM station with the EON
data. By using the EON data sent from a station,
you can tune into a different station of a different
network broadcasting your favorite programme or
traffic announcement while listening to another
programme or to another source such as CD.
By receiving the RDS data, this unit can do the
following:
Tracing the same programme automatically
(Network-Tracking Reception)
Standby Reception of TA (Traffic Announcement)
or your favorite programme
PTY (Programme Type) search
Programme search
And some other functions
Tracing the same programme
automatically (Network-Tracking
Reception)
When driving in an area where FM reception is not
good, the tuner built in this unit automatically tunes
into another RDS station, broadcasting the same
programme with stronger signals. So, you can
continue to listen to the same programme in its
finest reception, no matter where you drive. (See
the illustration on the next page.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly — PI
(Programme Identification) and AF (Alternative
Frequency.)
Without receiving these data correctly from the RDS
station you are listening to, Network-Tracking
Reception will not operate.
To use Network-Tracking Reception, press and
hold TP RDS (Traffic Programme/Radio Data
System) for more than 1 second. Each time you
press and hold the button, Network-Tracking
Reception modes change as follows:
Mode 1
The AF indicator lights up but the REG indicator
does not.
Network-Tracking Reception is activated with
Regionalization set to “off.
Switches to another station within the same network
when the receiving signals from the current station
become weak.
In this mode, the programme may differ from the one
currently received.
Mode 2
Both the AF indicator and the REG indicator light
up.
Network-Tracking Reception is activated with
Regionalization set to “on.
Switches to another station, within the same
network, broadcasting the same programme when
the receiving signals from the current station
become weak.
Mode 3
Neither the AF indicator nor the REG indicator lights
up.
Network-Tracking Reception is deactivated.
Mode 1 Mode 2 Mode 3
REG indicator
AF indicator
EN09-13.KD-S811/713/711R[E]14 07/12/2000, 05:14 PM9
10
ENGLISH
The same programme can be received on
different frequencies.
To deactivate the TA standby mode, press TP
RDS again.
PTY Standby Reception
When you press PTY while listening to
an FM station, the PTY indicator is lit
during reception of a PTY station and the
PTY standby mode is engaged. The
selected PTY name stored on page 11
flashes for 5 seconds.
When the station being received is not a PTY station,
the PTY indicator flashes. Press ¢
or 4
to engage the PTY standby mode. “SEARCH” appears
on the display, and PTY station search starts. When a
PTY station is tuned in, the PTY indicator is lit.
7 If you are listening to a CD and wish to listen to a
selected PTY broadcast, press PTY to enter the
PTY standby mode. (The PTY indicator lights up.)
If the selected PTY programme starts broadcasting
while the PTY standby mode is active, the selected
PTY name appears and the playback source
changes to the FM band. The selected PTY
programme can then be heard.
To deactivate the PTY standby mode, press PTY
again.
Selecting your favorite programme for
PTY Standby Reception
You can select your favorite programme for PTY
Standby Reception to store in memory.
When shipped from the factory, NEWS is stored
as the programme type for PTY Standby Reception.
1
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(PSM: see page 20.)
Using Standby Reception
Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) and Traffic Announcement (TA)
from the current source (another FM station and
CD)
Standby Reception will not work if you are listening
to an AM station.
TA Standby Reception
When you press TP RDS while listening
to an FM station, the TP indicator is lit
during reception of a TP (Traffic
Programme) station and the TA standby
mode is engaged.
When the station being received is not a TP station,
the TP indicator flashes. Press ¢
or 4
to engage the TA standby mode. SEARCH appears
on the display, and TP station search starts. When a
TP station is tuned in, the TP indicator is lit.
7 If you are listening to a CD and wish to listen to a
TP station, press TP RDS to enter the TA standby
mode. (The TP indicator lights up.)
If a traffic programme starts broadcasting while the
TA standby mode is active, TRAFFIC appears and
the playback source changes to the FM band. The
volume increases to the preset TA volume level (see
page 13) and the traffic programme can be heard.
Programme 1
broadcasting
on frequency C
Programme 1
broadcasting
on frequency D
Programme 1
broadcasting
on frequency B
Programme 1
broadcasting
on frequency E
Programme 1
broadcasting
on frequency A
EN09-13.KD-S811/713/711R[E]14 07/12/2000, 05:14 PM10
11
ENGLISH
Searching your favorite programme
You can search one of your 6 favorite programme
types stored in memory. When shipped from the
factory, the following 6 programme types have been
stored in the number buttons (1 to 6).
To store your favorite programme types,
see below.
To search your favorite programme type, see
page 12.
To store your favorite programme types
1
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(PSM: see page 20.)
2
Select “PTY STBY” (standby) if not
shown on the display.
3
Select one of twenty-nine PTY codes.
Selected code name appears
on the display and is stored
into memory.
For details, see the table
below.
4
Finish the setting.
PTY codes
NEWS: News
AFFAIRS: Topical programmes expanding
on current news or affairs
INFO: Programmes which impart
advice on a wide variety of
topics
SPORT: Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or
regional culture
SCIENCE: Programmes on natural science
and technology
VARIED: Other programmes like comedies
or ceremonies
POP M: Pop music
ROCK M: Rock music
EASY M: Easy-listening music
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,
the Stock Market, etc.
CHILDREN: Entertainment programmes for
children
SOCIAL: Programmes on social
activities
RELIGION: Programmes dealing with any
aspect of belief or faith, or the
nature of existence or ethics
PHONE IN: Programmes where people can
express their views either by
phone or in a public forum
TRAVEL: Programmes about travel
destinations, package tours,
and travel ideas and
opportunities
LEISURE: Programmes concerned with
recreational activities such as
gardening, cooking, fishing,
etc.
JAZZ: Jazz music
COUNTRY: Country music
NATION M: Current popular music from
another nation or region, in that
countrys language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT: Programmes dealing with
factual matters, presented in
an investigative style
POP M
1
2
3
ROCK M EASY M
45
6
CLASSICS
AFFAIRS
VARIED
CONTINUED ON THE NEXT PAGE
EN09-13.KD-S811/713/711R[E]14 07/12/2000, 05:14 PM11
12
ENGLISH
2
Select PTY SRCH (search) if not
shown on the display.
3
Select one of twenty-nine PTY codes.
(See page 11.)
Selected code name appears
on the display.
If the code already stored
in memory is selected, it
will flash on the display.
4
Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset
number you want.
The selected code name will flash on
the display.
5
Finish the setting.
To search your favorite programme type
1
Press and hold PTY (programme type)
for more than 1 second while listening
to an FM station.
The last selected PTY code appears.
2
Select one of PTY codes stored in
preset number buttons (1 to 6).
PTY search for your favorite programme starts
after 5 seconds.
If there is a station broadcasting a programme of
the same PTY code you selected, that station is
tuned in.
If there is no station broadcasting a programme
of the same PTY code you selected, the station
will not change.
Note:
In some areas, the PTY search will not work correctly.
Other convenient RDS functions
and adjustments
Automatic selection of the station
when using the number buttons
Usually when you press the number button, the
preset station is tuned in.
However, when the preset station is an RDS station,
something different will happen. If the signals from
that preset station are not sufficient for good
reception, this unit, using the AF data, tunes in
another frequency broadcasting the same
programme as the original preset station is
broadcasting. (Programme search)
Ex. When ROCK M is stored in preset number
button 2
EN09-13.KD-S811/713/711R[E]14 07/12/2000, 05:14 PM12
13
ENGLISH
To activate programme search, follow the procedure
below.
Programme search takes a while.
See also Changing the general settings (PSM)
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢ or 4 to select
P(Programme)-SEARCH.
3 Rotate the control dial clockwise to select ON.
Now programme search is activated.
To cancel programme search, repeat the same
procedure and select OFF in step 3 by rotating the
control dial counterclockwise.
Changing the display mode while
listening to an FM station
You can change the initial indication on the display
to station name (PS NAME), station frequency
(FREQ) or Clock time (CLOCK) while listening to
an FM RDS station.
See also Changing the general settings (PSM)
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢ or 4 to select DISPMODE
(display mode).
3 Rotate the control dial to set to the desired
indication (PS NAME, FREQ or "CLOCK").
Note:
By pressing DISP, you can also change the display while
listening to an FM RDS station.
Each time you press the button, the following information
appears on the display:
Then, the display goes back to the original indication
in several seconds.
Setting the TA volume level
You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the preset
level.
See also Changing the general settings (PSM)
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢ or 4 to select TA VOL.
3 Rotate the control dial to set to the desired
volume.
You can set it from VOL 00 to VOL 50.
Automatic clock adjustment
When shipped from the factory, the clock built in
this unit is set to be readjusted automatically using
the CT (Clock Time) data in the RDS signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.
See also Changing the general settings (PSM)
on page 19.
1 Press and hold SEL (select) for more than 2
seconds so that one of the PSM items appears
on the display.
2 Press ¢ or 4 to select AUTO ADJ.
3 Rotate the control dial counterclockwise to select
OFF.
Now automatic clock adjustment is canceled.
To reactivate clock adjustment, repeat the same
procedure and select ON in step 3 by rotating the
control dial clockwise.
Note:
It takes about 2 minutes to adjust the time using the CT
data. So, you should not change the station for more
than 2 minutes continuously; otherwise, the clock time
will not be adjusted.
Station name
(PS NAME)
Station frequency
(FREQ)
Programme type
(PTY)
CLOCK
(Clock time)
EN09-13.KD-S811/713/711R[E]14 07/12/2000, 05:14 PM13
14
ENGLISH
CD OPERATIONS
To stop play and eject the CD
Press 0.
CD play stops and the CD automatically ejects from
the loading slot.
If you change the source to FM or AM, the CD play
also stops (without ejecting the CD this time).
Notes:
If the ejected disc is not removed for about 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust. (CD play will not
start this time.)
You can eject the CD even when the unit is turned off.
Playing a CD
1
Insert a disc into the loading slot.
The unit turns on,
draws a CD and starts
playback automatically.
Note:
When a CD is inserted
upside down, the CD
automatically ejects.
The CD IN indicator lights up.
Total playing time of
the inserted disc
Total track number of
the inserted disc
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing CD
turns on the unit and starts playback automatically.
Elapsed playing
time
Current track
EN14-16.KD-S811/713/711R[E]15 07/12/2000, 05:13 PM14
15
ENGLISH
Selecting CD playback modes
To play back tracks at random (Random Play)
You can play back all tracks on the CD at random.
Each time you press MO RND (monaural/random)
while playing a CD, CD random play mode turns
on and off alternately.
When the random mode is turned on, the RND
indicator lights up on the display and a track
randomly selected starts playing.
Locating a track or a particular
portion on a CD
To fast-forward or reverse the track
To go to the next tracks or the previous
tracks
To go to a particular track directly
Press the number button corresponding to the
track number to start its playback.
To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.
Press and hold ¢
, while
playing a CD, to fast-forward the
track.
Press and hold 4
, while
playing a CD, to reverse the
track.
Press
¢ briefly, while
playing a CD, to go ahead to the
beginning of the next track. Each
time you press the button
consecutively, the beginning of
the next tracks is located and
played back.
Press 4
briefly, while
playing a CD, to go back to the
beginning of the current track.
Each time you press the button
consecutively, the beginning of
the previous tracks is located
and played back.
The RND indicator
EN14-16.KD-S811/713/711R[E]15 07/12/2000, 05:13 PM15
16
ENGLISH
Prohibiting CD ejection
You can prohibit CD ejection and can lock a CD in
the loading slot.
Press and hold CD and 0 for more than 2
seconds.
EJECT flashes on the display for about 5
seconds, and the CD is locked and cannot be
ejected.
To cancel the prohibition and unlock the CD,
press and hold CD and 0 again for more than 2
seconds, while pressing CD. EJECT appears on
the display, and the CD ejects from the loading slot.
EN14-16.KD-S811/713/711R[E]15 07/12/2000, 05:13 PM16
17
ENGLISH
2
Adjust the level.
Note:
Normally the control dial works for volume
adjustment. So you do not have to select “VOL” to
adjust the volume level.
Using the Sound Control
Memory (SCM)
You can select and store a preset sound adjustment
suitable for each playback source.
(Advanced SCM)
Selecting and storing the sound modes
Once you select a sound mode, it is stored in
memory. It will be recalled every time you select
the same source and will be shown on the display.
A sound mode can be stored for each of the
following sources — FM1, FM2, FM3, AM and CD.
If you do not want to store the sound mode
separately for each playback source, but want to
use the same sound mode for all the sources,
see “To cancel Advanced SCM” on page 21.
Select the sound mode you want.
Each time you press the button, the
sound mode changes as follows:
SOUND ADJUSTMENTS
FAD
BAL
VOL
BAS
TRE
(volume)
LOUD
(loudness)
(bass) (treble) (fader)
(balance)
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
Select the item you want to adjust.
Each time you press the button, the
adjustable items change as
follows:
Indication To do: Range
BAS Adjust the bass. 06 (min.)
|
+06 (max.)
TRE Adjust the treble. 06 (min.)
|
+06 (max.)
FAD* Adjust the front R06 (Rear only)
and rear speaker |
balance. F06 (Front only)
BAL Adjust the left L06 (Left only)
and right speaker |
balance. R06 (Right only)
LOUD Boost low and high
frequencies to LOUD ON
produce a well- |
balanced sound LOUD OFF
at low volume
level.
VOL Adjust the volume. 00 (min.)
|
50 (max.)
* If you are using a two-speaker system, set the fader
level to 00.
Equalization pattern changes as you adjust
the bass or treble.
To increase the level.
To decrease the level.
BEAT
SOFT
POP SCM OFF
EN17-18.KD-S811.713.711R[E]16 07/12/2000, 05:18 PM17
18
ENGLISH
When SCM LINK is set to LINK ON, the
selected sound mode can be stored in memory
for the current source and the effect applies only
to the current source. Each time you change the
playback source, the SCM indicator flashes on
the display.
When SCM LINK is set to LINK OFF, the
selected sound mode effect applies to any source.
Indication For: Preset values
BAS TRE LOUD
BEAT Rock or disco +02 00 ON
music
SOFT Quiet +01 03 OFF
background
music
POP Light music +04 +01 OFF
SCM OFF (Flat sound) 00 00 ON
Storing your own sound
adjustments
You can adjust the sound modes (BEAT, SOFT,
POP) to your preference and store your own
adjustments in memory.
There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.
1
Call up the sound mode you want to
adjust.
See the left column for details.
2
Select “BAS (Bass), “TRE (Treble)”
or “LOUD (Loudness).”
3
Adjust the bass or treble level or turn
the loudness function ON/OFF.
See page 17 for details.
4
Repeat steps 2 and 3 to adjust the
other items.
5
Press and hold SCM until the sound
mode you have selected in step 1
flashes on the display.
Your adjustment made for the selected
sound mode is stored in memory.
6
Repeat the same procedure to store
other sound modes.
To reset to the factory settings
Repeat the same procedure and reassign the
preset values listed in the table on the left
column.
Recalling the sound modes
When SCM LINK is set to LINK ON,
Select the source.
The sound mode stored in memory for the
selected source is recalled.
Notes:
You can adjust each sound mode to your preference,
and store it in memory.
If you want to adjust and store your original sound
mode, see Storing your own sound adjustments on
the right column.
To adjust the bass and treble reinforcement levels or
to turn on/off the loudness function temporarily, see
page 17. (Your adjustments will be canceled if another
source is selected.)
EN17-18.KD-S811.713.711R[E]16 07/12/2000, 05:18 PM18
19
ENGLISH
Setting the clock
You can also set the clock system either 24 hours
or 12 hours.
1
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)
2
Set the hour.
1 Select “CLOCK H” if not shown on the
display.
2 Adjust the hour.
3
Set the minute.
1 Select “CLOCK M.
2 Adjust the minute.
4
Set the clock system.
1 Select “24H/12H.
2 Select “24H” or “12H.
5
Finish the setting.
To check the current clock time while the unit
is turned off, press DISP (display).
The power turns on, the clock time is shown for
5 seconds, then the power turns off.
Changing the general settings
(PSM)
You can change the items listed on the next page
by using the PSM (Preferred Setting Mode) control.
Basic Procedure
1
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 20.)
2
Select the PSM item you want to
adjust. (See page 20.)
3
Adjust the PSM item selected above.
4
Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
5
Finish the setting.
OTHER MAIN FUNCTIONS
2
1
1
2
1
2
EN19-22.KD-S811/713/711R[E]-1 07/12/2000, 05:17 PM19
20
ENGLISH
Preferred Setting Mode (PSM) items
LINK ON
0:00
24H
24H
12H
ON
OFF
LINK OFF
19
18, 21
19
13
LINK ON
Back Advance
AdvanceBack
ON
See
page
Factory-
preset
settings
Hold.
Select.
2
1
3
Clockwise
Set.
Counter-
clockwise
OFF ON
VOL 00 VOL 50
AUDIO 2
OFF
MUTING 1
MUTING 2
29 programme types
(see page 11.)
13
13
OFF
VOL 20
21
OFF
AUDIO 2
21
CLOCK H Hour adjustment
CLOCK M Minute adjustment
SCM LINK Sound control
memory linkage
24H/12H 24/12-hour time
display
AUTO ADJ Automatic clock
setting
DISPMODE Display mode
PTY STBY PTY standby
PTY SRCH PTY search
TA VOL Traffic announcement
volume
P-SEARCH Programme search
LEVEL Level display
TEL Telephone muting
OFF
AUDIO 1
CLOCK
FREQ
PS NAME
(See page 11.)
11
NEWS
11
13
PS NAME
Press SEL (select) to finish the setting.
EN19-22.KD-S811/713/711R[E]-1 07/12/2000, 05:17 PM20
21
ENGLISH
To cancel Advanced SCM – SCM LINK
You can cancel the Advanced SCM (Sound Control
Memory), and unlink the sound modes and the
playback sources.
When shipped from the factory, a different sound
mode can be stored in memory for each source so
that you can change the sound modes simply by
changing the sources.
LINK ON: Advanced SCM (different sound
modes for different sources)
LINK OFF: Conventional SCM (one sound
mode for all sources)
To select the level meter – LEVEL
You can select the level display according to your
preference.
When shipped from the factory, AUDIO 2 is
selected.
AUDIO 1:
Level meter illuminates from bottom
to top.
AUDIO 2:
Alternates level meter (moves from
bottom to top) and illumination
display.
OFF:
Erases the audio level indicator.
To select the telephone muting – TEL
This mode is used when a cellular phone system is
connected. Depending on the phone system used,
select either MUTING 1 or MUTING 2, whichever
mutes the sounds from this unit. When shipped from
the factory, this mode is deactivated.
MUTING 1: Select this if this setting can mute
the sounds.
MUTING 2: Select this if this setting can mute
the sounds.
OFF: Cancels the telephone muting.
EN19-22.KD-S811/713/711R[E]-1 07/12/2000, 05:17 PM21
22
ENGLISH
Detaching the control panel
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1
Unlock the control panel.
2
Pull the control panel out of the unit.
3
Put the detached control panel into
the provided case.
Attaching the control panel
1
Insert the left side of the control panel
into the groove on the panel holder.
2
Press the right side of the control
panel to fix it to the panel holder.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
Connectors
EN19-22.KD-S811/713/711R[E]-1 07/12/2000, 05:17 PM22
23
ENGLISH
REMOTE CONTROLLER
Preparing the remote controller
(With an optionally purchased remote controller)
(only for KD-S811R)
We recommend that you use remote controller
RM-RK31 with your unit. The followings are the
instructions for using RM-RK31.
Before using the remote controller:
Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
Do not expose the remote sensor to strong light
(direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of the
remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point pen
or a similar tool.
2) Remove the battery holder.
2. Place the battery.
Slide the battery into the holder with the + side
facing upwards so that the battery is fixed in
the holder.
Lithium coin battery
(product number:
CR2025)
3. Return the battery holder.
Insert again the battery holder pushing it until
you hear a clicking sound.
(back side)
WARNING:
Store the battery in a place where children cannot
reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
Do not recharge, short, disassemble or heat the
battery or dispose it in a fire.
Doing any of these things may cause the battery to
give off heat, crack or start a fire.
Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off heat,
crack or start a fire.
When throwing away or saving the battery, wrap it
in tape and insulate; otherwise, the battery may
start to give off heat, crack or start a fire.
Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off heat,
crack or start a fire.
Remote sensor
1)
2)
(back side)
EN23-24.KD-S811/713/711R[E]16 07/12/2000, 05:16 PM23
24
ENGLISH
Using the remote controller
1
2
3
4
6
7
5
1 Functions the same as the button on
the main unit.
2 Functions as the BAND button while listening
to the radio.
Each time you press the button, the band
changes.
Does not function as the PROG/DISC + button.
3 Functions as the PRESET button while
listening to the radio.
Each time you press the button, the preset
station number increases, and the selected
station is tuned in.
Does not function as the DISC button.
4 Functions the same as the control dial on the
main unit.
Note: This button does not function for the preferred
settings mode adjustment.
5 Selects the sound mode.
Each time you press SCM (Sound Control
Memory), the mode changes.
6 Selects the source.
Each time you press FUNC (function), the
source changes.
7 Searches stations while listening to the radio.
Fast forwards or reverses the track if pressed
and held while listening to a CD.
Skips to the beginning of the next tracks or
goes back to the beginning of the current (or
previous tracks) if pressed briefly while
listening to a CD.
EN23-24.KD-S811/713/711R[E]16 07/12/2000, 05:16 PM24
25
ENGLISH
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Causes
CD is inserted upside down.
You are driving on rough roads.
The disc is scratched.
Connections are incorrect.
Connections are incorrect.
The volume is turned to the
minimum level.
Connections are incorrect.
Signals are too weak.
The antenna is not connected
firmly.
No CD is inserted.
CD is locked.
The unit may function
incorrectly.
The built-in microcomputer may
function incorrectly due to noise,
etc.
Symptoms
CD cannot be played back.
CD sound is sometimes
interrupted.
Sound is sometimes
interrupted.
Sound cannot be heard from
the speakers.
SSM (Strong-station
Sequential Memory)
automatic preset does not
work.
Static noise while listening to
the radio.
“NO DISC” appears on the
display.
CD cannot be ejected.
CD can be neither played
back nor ejected.
This unit does not work at all.
Remedies
Insert the CD correctly.
Stop playing CD while driving
on rough roads.
Change the disc.
Check the cords and
connections.
Check the cords and
connections.
Adjust it to the optimum level.
Check the cords and
connections.
Store stations manually.
Connect the antenna firmly.
Insert a CD correctly.
Unlock the CD (see page 16).
Press and hold both
and 0 at the same time for
several seconds.
Be careful not to drop CD when
it is ejected.
Press and hold both SEL and
at the same time for
several seconds to reset the
unit. (The clock setting and
preset stations stored in
memory are erased.) (See
page 2.)
EN25-27.KD-S811/713/711R[E]15 07/12/2000, 05:16 PM25
26
ENGLISH
MAINTENANCE
Handling CDs
This unit has been designed only to reproduce
the CDs bearing the following marks.
Other discs cannot be played back.
How to handle CDs
When removing a CD
from its case, press
down the center holder
of the case and lift the
CD out, holding it by the
edges.
Always hold the CD by the edges. Do not touch
its recording surface.
When storing a CD into its case, gently insert the
CD around the center holder (with the printed
surface facing up).
Make sure to store CDs into the cases after
use.
To keep CDs clean
A dirty CD may not play
correctly. If a CD does
become dirty, wipe it with a
soft cloth in a straight line
from center to edge.
To play new CDs
New CDs may have some
rough spots around the
inner and outer edges. If
such a CD is used, this unit
may reject the CD.
To remove these rough
spots, rub the edges with a
pencil or ball-point pen, etc.
About mistracking:
Mistracking may result from driving on extremely
rough roads. This does not damage the unit and the
CD, but will be annoying.
We recommend that you stop CD play while
driving on such rough roads.
COMPACT
DIGITAL AUDIO
Center holder
Moisture condensation
Moisture may condense on the lens inside the
CD player in the following cases:
After starting the heater in the car.
If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the CD and leave
the unit turned on for a few hours until the
moisture evaporates.
When playing a CD-R (Recordable)
You can play back your original CD-Rs on this
receiver.
Before playing back CD-Rs, read their
instructions or cautions carefully.
Some CD-Rs recorded on CD recorders may
not be played back on this receiver because of
their disc characteristics, and of the following
reasons:
Discs are dirty or scratched.
Moisture condensation occurs on the lens
inside the unit.
The pickup lens inside the CD player is dirty.
Use only finalized CD-Rs.
CD-RWs (Rewritable) cannot be played back
on this receiver.
Do not use CD-Rs with stickers or sticking
labels on the surface. They may cause
malfunctions.
CAUTIONS:
Do not insert 8 cm CDs (single CDs) into the
loading slot. (Such CDs cannot be ejected.)
Do not insert any CD of unusual shape — like a
heart or flower; otherwise, it will cause a
malfunction.
Do not expose CDs to direct sunlight or any heat
source or place them in a place subject to high
temperature and humidity. Do not leave them in
a car.
Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean CDs.
EN25-27.KD-S811/713/711R[E]15 07/12/2000, 05:16 PM26
27
ENGLISH
SPECIFICATIONS
AUDIO AMPLIFIER SECTION
(For KD-S811R)
Maximum Power Output:
Front: 45 W per channel
Rear: 45 W per channel
Continuous Power Output (RMS):
Front: 17 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear: 17 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
(For KD-S713R/KD-S711R)
Maximum Power Output:
Front: 40 W per channel
Rear: 40 W per channel
Continuous Power Output (RMS):
Front: 16 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear: 16 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than
0.8% total harmonic distortion.
Load Impedance: 4 (4 to 8 allowance)
Tone Control Range:
Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 k load (full scale)
Output Impedance: 1 k
TUNER SECTION
Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: (MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 )
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 )
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB
[MW Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
[LW Tuner]
Sensitivity: 50 µV
CD PLAYER SECTION
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
GENERAL
Power Requirement:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Installation Size: 182 mm × 52 mm × 150 mm
Panel Size: 188 mm × 58 mm × 14 mm
Mass: 1.3 kg (excluding accessories)
Design and specifications subject to change without
notice.
EN25-27.KD-S811/713/711R[E]15 07/12/2000, 05:16 PM27
EN, GE, FR, NL
1100HISFLEJES
VICTOR COMPANY OF JAPAN, LIMITED
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Haben Sie PROBLEME mit dem Betrieb?
Bitte setzen Sie Ihr Gerät zurück
Siehe Seite Zurücksetzen des Geräts
Vous avez des PROBLÈMES de fonctionnement?
Réinitialisez votre appareil
Référez-vous à la page intitulée Comment réinitialiser votre appareil
Hebt u PROBLEMEN met de bediening?
Stel het apparaat terug
Zie de pagina met de paragraaf Het apparaat terugstellen
J
V
C
COVER.KD-S811R[E].001A/5 07/12/2000, 05:05 PM2
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC kd s 811 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC kd s 811 r in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC kd s 811 r

JVC kd s 811 r User Manual - Dutch, Italian, Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info