682985
37
Zoom out
Zoom in
Previous page
1/152
Next page
ENGLISH
33
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
Bluetooth®
The connected Bluetooth
audio player cannot be
controlled.
Check whether the connected Bluetooth audio player
supports Audio/Video Remote Control Profile (AVRCP).
(Refer to the instructions of your audio player.)
Disconnect and connect the Bluetooth player again.
“PLEASE WAIT”
The unit is preparing to use the Bluetooth function. If
the message does not disappear, turn off and turn on
the unit, then connect the device again.
“NOT SUPPORT”
The connected phone does not support Voice
Recognition feature.
“ERROR”
Try the operation again. If “ERROR” appears again, check
if the device supports the function you have tried.
“H/W ERROR”
Reset the unit and try the operation again. If “H/W
ERROR” appears again, consult your nearest service
center.
“SWITCHING NG”
The connected phones might not support phone
switching feature.
If you still have troubles, reset the unit.
( 3
or
4)
INSTALLATION/CONNECTION
Warning
The unit can only be used with a 12V DC power supply, negative ground.
Disconnect the battery’s negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
To prevent short circuit:
Insulate unconnected wires with vinyl tape.
Be sure to ground this unit to the car’s chassis again after installation.
Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into
contact with metal parts to protect the wires.
Caution
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and
shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
Do not connect the
wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
Connect speakers with a maximum power of more than 50W. If the maximum power of the
speakers is lower than 50W, change the [AMP GAIN] setting to avoid damaging the speakers.
(
22)
Mount the unit at an angle of less than 30º.
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to
the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and
off by the ignition key.
Keep all cables away from heat dissipate metal parts.
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse
with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then disconnect the terminal of the car
battery.
2 Connect the wires properly.
See Wiring connection. (
35)
3 Install the unit to your car.
See Installing the unit (in-dash mounting). (
34)
4 Connect the
terminal of the car battery.
5 Press source button to turn on the power.
6 Detach the faceplate and reset the unit within 5 seconds. ( 3 or 4)
JS_JVC_KD_R992BT_E_EN_3.indd 33JS_JVC_KD_R992BT_E_EN_3.indd 33 7/27/2017 9:47:21 AM7/27/2017 9:47:21 AM
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC KD-R792BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC KD-R792BT in the language / languages: English, Dutch, Portuguese, Spanish as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC KD-R792BT

JVC KD-R792BT User Manual - German, French, Italian - 152 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info